| // SPDX-License-Identifier: GPL-2.0+ | |
| /* | |
| * Copyright (C) 2020 Amarula Solutions(India) | |
| * Author: Jagan Teki <jagan@amarulasolutions.com> | |
| */ | |
| #include <drm/drm_atomic_helper.h> | |
| #include <drm/drm_of.h> | |
| #include <drm/drm_print.h> | |
| #include <drm/drm_mipi_dsi.h> | |
| #include <linux/bitfield.h> | |
| #include <linux/bits.h> | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/i2c.h> | |
| #include <linux/media-bus-format.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/regmap.h> | |
| #include <linux/regulator/consumer.h> | |
| #define VENDOR_ID 0x00 | |
| #define DEVICE_ID_H 0x01 | |
| #define DEVICE_ID_L 0x02 | |
| #define VERSION_ID 0x03 | |
| #define FIRMWARE_VERSION 0x08 | |
| #define CONFIG_FINISH 0x09 | |
| #define PD_CTRL(n) (0x0a + ((n) & 0x3)) /* 0..3 */ | |
| #define RST_CTRL(n) (0x0e + ((n) & 0x1)) /* 0..1 */ | |
| #define SYS_CTRL(n) (0x10 + ((n) & 0x7)) /* 0..4 */ | |
| #define SYS_CTRL_1_CLK_PHASE_MSK GENMASK(5, 4) | |
| #define CLK_PHASE_0 0 | |
| #define CLK_PHASE_1_4 1 | |
| #define CLK_PHASE_1_2 2 | |
| #define CLK_PHASE_3_4 3 | |
| #define RGB_DRV(n) (0x18 + ((n) & 0x3)) /* 0..3 */ | |
| #define RGB_DLY(n) (0x1c + ((n) & 0x1)) /* 0..1 */ | |
| #define RGB_TEST_CTRL 0x1e | |
| #define ATE_PLL_EN 0x1f | |
| #define HACTIVE_LI 0x20 | |
| #define VACTIVE_LI 0x21 | |
| #define VACTIVE_HACTIVE_HI 0x22 | |
| #define HFP_LI 0x23 | |
| #define HSYNC_LI 0x24 | |
| #define HBP_LI 0x25 | |
| #define HFP_HSW_HBP_HI 0x26 | |
| #define HFP_HSW_HBP_HI_HFP(n) (((n) & 0x300) >> 4) | |
| #define HFP_HSW_HBP_HI_HS(n) (((n) & 0x300) >> 6) | |
| #define HFP_HSW_HBP_HI_HBP(n) (((n) & 0x300) >> 8) | |
| #define VFP 0x27 | |
| #define VSYNC 0x28 | |
| #define VBP 0x29 | |
| #define BIST_POL 0x2a | |
| #define BIST_POL_BIST_MODE(n) (((n) & 0xf) << 4) | |
| #define BIST_POL_BIST_GEN BIT(3) | |
| #define BIST_POL_HSYNC_POL BIT(2) | |
| #define BIST_POL_VSYNC_POL BIT(1) | |
| #define BIST_POL_DE_POL BIT(0) | |
| #define BIST_RED 0x2b | |
| #define BIST_GREEN 0x2c | |
| #define BIST_BLUE 0x2d | |
| #define BIST_CHESS_X 0x2e | |
| #define BIST_CHESS_Y 0x2f | |
| #define BIST_CHESS_XY_H 0x30 | |
| #define BIST_FRAME_TIME_L 0x31 | |
| #define BIST_FRAME_TIME_H 0x32 | |
| #define FIFO_MAX_ADDR_LOW 0x33 | |
| #define SYNC_EVENT_DLY 0x34 | |
| #define HSW_MIN 0x35 | |
| #define HFP_MIN 0x36 | |
| #define LOGIC_RST_NUM 0x37 | |
| #define OSC_CTRL(n) (0x48 + ((n) & 0x7)) /* 0..5 */ | |
| #define BG_CTRL 0x4e | |
| #define LDO_PLL 0x4f | |
| #define PLL_CTRL(n) (0x50 + ((n) & 0xf)) /* 0..15 */ | |
| #define PLL_CTRL_6_EXTERNAL 0x90 | |
| #define PLL_CTRL_6_MIPI_CLK 0x92 | |
| #define PLL_CTRL_6_INTERNAL 0x93 | |
| #define PLL_REM(n) (0x60 + ((n) & 0x3)) /* 0..2 */ | |
| #define PLL_DIV(n) (0x63 + ((n) & 0x3)) /* 0..2 */ | |
| #define PLL_FRAC(n) (0x66 + ((n) & 0x3)) /* 0..2 */ | |
| #define PLL_INT(n) (0x69 + ((n) & 0x1)) /* 0..1 */ | |
| #define PLL_REF_DIV 0x6b | |
| #define PLL_REF_DIV_P(n) ((n) & 0xf) | |
| #define PLL_REF_DIV_Pe BIT(4) | |
| #define PLL_REF_DIV_S(n) (((n) & 0x7) << 5) | |
| #define PLL_SSC_P(n) (0x6c + ((n) & 0x3)) /* 0..2 */ | |
| #define PLL_SSC_STEP(n) (0x6f + ((n) & 0x3)) /* 0..2 */ | |
| #define PLL_SSC_OFFSET(n) (0x72 + ((n) & 0x3)) /* 0..3 */ | |
| #define GPIO_OEN 0x79 | |
| #define MIPI_CFG_PW 0x7a | |
| #define MIPI_CFG_PW_CONFIG_DSI 0xc1 | |
| #define MIPI_CFG_PW_CONFIG_I2C 0x3e | |
| #define GPIO_SEL(n) (0x7b + ((n) & 0x1)) /* 0..1 */ | |
| #define IRQ_SEL 0x7d | |
| #define DBG_SEL 0x7e | |
| #define DBG_SIGNAL 0x7f | |
| #define MIPI_ERR_VECTOR_L 0x80 | |
| #define MIPI_ERR_VECTOR_H 0x81 | |
| #define MIPI_ERR_VECTOR_EN_L 0x82 | |
| #define MIPI_ERR_VECTOR_EN_H 0x83 | |
| #define MIPI_MAX_SIZE_L 0x84 | |
| #define MIPI_MAX_SIZE_H 0x85 | |
| #define DSI_CTRL 0x86 | |
| #define DSI_CTRL_UNKNOWN 0x28 | |
| #define DSI_CTRL_DSI_LANES(n) ((n) & 0x3) | |
| #define MIPI_PN_SWAP 0x87 | |
| #define MIPI_PN_SWAP_CLK BIT(4) | |
| #define MIPI_PN_SWAP_D(n) BIT((n) & 0x3) | |
| #define MIPI_SOT_SYNC_BIT(n) (0x88 + ((n) & 0x1)) /* 0..1 */ | |
| #define MIPI_ULPS_CTRL 0x8a | |
| #define MIPI_CLK_CHK_VAR 0x8e | |
| #define MIPI_CLK_CHK_INI 0x8f | |
| #define MIPI_T_TERM_EN 0x90 | |
| #define MIPI_T_HS_SETTLE 0x91 | |
| #define MIPI_T_TA_SURE_PRE 0x92 | |
| #define MIPI_T_LPX_SET 0x94 | |
| #define MIPI_T_CLK_MISS 0x95 | |
| #define MIPI_INIT_TIME_L 0x96 | |
| #define MIPI_INIT_TIME_H 0x97 | |
| #define MIPI_T_CLK_TERM_EN 0x99 | |
| #define MIPI_T_CLK_SETTLE 0x9a | |
| #define MIPI_TO_HS_RX_L 0x9e | |
| #define MIPI_TO_HS_RX_H 0x9f | |
| #define MIPI_PHY(n) (0xa0 + ((n) & 0x7)) /* 0..5 */ | |
| #define MIPI_PD_RX 0xb0 | |
| #define MIPI_PD_TERM 0xb1 | |
| #define MIPI_PD_HSRX 0xb2 | |
| #define MIPI_PD_LPTX 0xb3 | |
| #define MIPI_PD_LPRX 0xb4 | |
| #define MIPI_PD_CK_LANE 0xb5 | |
| #define MIPI_FORCE_0 0xb6 | |
| #define MIPI_RST_CTRL 0xb7 | |
| #define MIPI_RST_NUM 0xb8 | |
| #define MIPI_DBG_SET(n) (0xc0 + ((n) & 0xf)) /* 0..9 */ | |
| #define MIPI_DBG_SEL 0xe0 | |
| #define MIPI_DBG_DATA 0xe1 | |
| #define MIPI_ATE_TEST_SEL 0xe2 | |
| #define MIPI_ATE_STATUS(n) (0xe3 + ((n) & 0x1)) /* 0..1 */ | |
| struct chipone { | |
| struct device *dev; | |
| struct regmap *regmap; | |
| struct i2c_client *client; | |
| struct drm_bridge bridge; | |
| struct drm_display_mode mode; | |
| struct drm_bridge *panel_bridge; | |
| struct mipi_dsi_device *dsi; | |
| struct gpio_desc *enable_gpio; | |
| struct regulator *vdd1; | |
| struct regulator *vdd2; | |
| struct regulator *vdd3; | |
| struct clk *refclk; | |
| unsigned long refclk_rate; | |
| bool interface_i2c; | |
| }; | |
| static const struct regmap_range chipone_dsi_readable_ranges[] = { | |
| regmap_reg_range(VENDOR_ID, VERSION_ID), | |
| regmap_reg_range(FIRMWARE_VERSION, PLL_SSC_OFFSET(3)), | |
| regmap_reg_range(GPIO_OEN, MIPI_ULPS_CTRL), | |
| regmap_reg_range(MIPI_CLK_CHK_VAR, MIPI_T_TA_SURE_PRE), | |
| regmap_reg_range(MIPI_T_LPX_SET, MIPI_INIT_TIME_H), | |
| regmap_reg_range(MIPI_T_CLK_TERM_EN, MIPI_T_CLK_SETTLE), | |
| regmap_reg_range(MIPI_TO_HS_RX_L, MIPI_PHY(5)), | |
| regmap_reg_range(MIPI_PD_RX, MIPI_RST_NUM), | |
| regmap_reg_range(MIPI_DBG_SET(0), MIPI_DBG_SET(9)), | |
| regmap_reg_range(MIPI_DBG_SEL, MIPI_ATE_STATUS(1)), | |
| }; | |
| static const struct regmap_access_table chipone_dsi_readable_table = { | |
| .yes_ranges = chipone_dsi_readable_ranges, | |
| .n_yes_ranges = ARRAY_SIZE(chipone_dsi_readable_ranges), | |
| }; | |
| static const struct regmap_range chipone_dsi_writeable_ranges[] = { | |
| regmap_reg_range(CONFIG_FINISH, PLL_SSC_OFFSET(3)), | |
| regmap_reg_range(GPIO_OEN, MIPI_ULPS_CTRL), | |
| regmap_reg_range(MIPI_CLK_CHK_VAR, MIPI_T_TA_SURE_PRE), | |
| regmap_reg_range(MIPI_T_LPX_SET, MIPI_INIT_TIME_H), | |
| regmap_reg_range(MIPI_T_CLK_TERM_EN, MIPI_T_CLK_SETTLE), | |
| regmap_reg_range(MIPI_TO_HS_RX_L, MIPI_PHY(5)), | |
| regmap_reg_range(MIPI_PD_RX, MIPI_RST_NUM), | |
| regmap_reg_range(MIPI_DBG_SET(0), MIPI_DBG_SET(9)), | |
| regmap_reg_range(MIPI_DBG_SEL, MIPI_ATE_STATUS(1)), | |
| }; | |
| static const struct regmap_access_table chipone_dsi_writeable_table = { | |
| .yes_ranges = chipone_dsi_writeable_ranges, | |
| .n_yes_ranges = ARRAY_SIZE(chipone_dsi_writeable_ranges), | |
| }; | |
| static const struct regmap_config chipone_regmap_config = { | |
| .reg_bits = 8, | |
| .val_bits = 8, | |
| .rd_table = &chipone_dsi_readable_table, | |
| .wr_table = &chipone_dsi_writeable_table, | |
| .cache_type = REGCACHE_MAPLE, | |
| .max_register = MIPI_ATE_STATUS(1), | |
| }; | |
| static int chipone_dsi_read(void *context, | |
| const void *reg, size_t reg_size, | |
| void *val, size_t val_size) | |
| { | |
| struct mipi_dsi_device *dsi = context; | |
| const u16 reg16 = (val_size << 8) | *(u8 *)reg; | |
| int ret; | |
| ret = mipi_dsi_generic_read(dsi, ®16, 2, val, val_size); | |
| return ret == val_size ? 0 : -EINVAL; | |
| } | |
| static int chipone_dsi_write(void *context, const void *data, size_t count) | |
| { | |
| struct mipi_dsi_device *dsi = context; | |
| return mipi_dsi_generic_write(dsi, data, 2); | |
| } | |
| static const struct regmap_bus chipone_dsi_regmap_bus = { | |
| .read = chipone_dsi_read, | |
| .write = chipone_dsi_write, | |
| .reg_format_endian_default = REGMAP_ENDIAN_NATIVE, | |
| .val_format_endian_default = REGMAP_ENDIAN_NATIVE, | |
| }; | |
| static inline struct chipone *bridge_to_chipone(struct drm_bridge *bridge) | |
| { | |
| return container_of(bridge, struct chipone, bridge); | |
| } | |
| static void chipone_readb(struct chipone *icn, u8 reg, u8 *val) | |
| { | |
| int ret, pval; | |
| ret = regmap_read(icn->regmap, reg, &pval); | |
| *val = ret ? 0 : pval & 0xff; | |
| } | |
| static int chipone_writeb(struct chipone *icn, u8 reg, u8 val) | |
| { | |
| return regmap_write(icn->regmap, reg, val); | |
| } | |
| static void chipone_configure_pll(struct chipone *icn, | |
| const struct drm_display_mode *mode) | |
| { | |
| unsigned int best_p = 0, best_m = 0, best_s = 0; | |
| unsigned int mode_clock = mode->clock * 1000; | |
| unsigned int delta, min_delta = 0xffffffff; | |
| unsigned int freq_p, freq_s, freq_out; | |
| unsigned int p_min, p_max; | |
| unsigned int p, m, s; | |
| unsigned int fin; | |
| bool best_p_pot; | |
| u8 ref_div; | |
| /* | |
| * DSI byte clock frequency (input into PLL) is calculated as: | |
| * DSI_CLK = HS clock / 4 | |
| * | |
| * DPI pixel clock frequency (output from PLL) is mode clock. | |
| * | |
| * The chip contains fractional PLL which works as follows: | |
| * DPI_CLK = ((DSI_CLK / P) * M) / S | |
| * P is pre-divider, register PLL_REF_DIV[3:0] is 1:n divider | |
| * register PLL_REF_DIV[4] is extra 1:2 divider | |
| * M is integer multiplier, register PLL_INT(0) is multiplier | |
| * S is post-divider, register PLL_REF_DIV[7:5] is 2^(n+1) divider | |
| * | |
| * It seems the PLL input clock after applying P pre-divider have | |
| * to be lower than 20 MHz. | |
| */ | |
| if (icn->refclk) | |
| fin = icn->refclk_rate; | |
| else | |
| fin = icn->dsi->hs_rate / 4; /* in Hz */ | |
| /* Minimum value of P predivider for PLL input in 5..20 MHz */ | |
| p_min = clamp(DIV_ROUND_UP(fin, 20000000), 1U, 31U); | |
| p_max = clamp(fin / 5000000, 1U, 31U); | |
| for (p = p_min; p < p_max; p++) { /* PLL_REF_DIV[4,3:0] */ | |
| if (p > 16 && p & 1) /* P > 16 uses extra /2 */ | |
| continue; | |
| freq_p = fin / p; | |
| if (freq_p == 0) /* Divider too high */ | |
| break; | |
| for (s = 0; s < 0x7; s++) { /* PLL_REF_DIV[7:5] */ | |
| freq_s = freq_p / BIT(s + 1); | |
| if (freq_s == 0) /* Divider too high */ | |
| break; | |
| m = mode_clock / freq_s; | |
| /* Multiplier is 8 bit */ | |
| if (m > 0xff) | |
| continue; | |
| /* Limit PLL VCO frequency to 1 GHz */ | |
| freq_out = (fin * m) / p; | |
| if (freq_out > 1000000000) | |
| continue; | |
| /* Apply post-divider */ | |
| freq_out /= BIT(s + 1); | |
| delta = abs(mode_clock - freq_out); | |
| if (delta < min_delta) { | |
| best_p = p; | |
| best_m = m; | |
| best_s = s; | |
| min_delta = delta; | |
| } | |
| } | |
| } | |
| best_p_pot = !(best_p & 1); | |
| dev_dbg(icn->dev, | |
| "PLL: P[3:0]=%d P[4]=2*%d M=%d S[7:5]=2^%d delta=%d => DSI f_in(%s)=%d Hz ; DPI f_out=%d Hz\n", | |
| best_p >> best_p_pot, best_p_pot, best_m, best_s + 1, | |
| min_delta, icn->refclk ? "EXT" : "DSI", fin, | |
| (fin * best_m) / (best_p << (best_s + 1))); | |
| ref_div = PLL_REF_DIV_P(best_p >> best_p_pot) | PLL_REF_DIV_S(best_s); | |
| if (best_p_pot) /* Prefer /2 pre-divider */ | |
| ref_div |= PLL_REF_DIV_Pe; | |
| /* Clock source selection either external clock or MIPI DSI clock lane */ | |
| chipone_writeb(icn, PLL_CTRL(6), | |
| icn->refclk ? PLL_CTRL_6_EXTERNAL : PLL_CTRL_6_MIPI_CLK); | |
| chipone_writeb(icn, PLL_REF_DIV, ref_div); | |
| chipone_writeb(icn, PLL_INT(0), best_m); | |
| } | |
| static void chipone_atomic_enable(struct drm_bridge *bridge, | |
| struct drm_atomic_commit *state) | |
| { | |
| struct chipone *icn = bridge_to_chipone(bridge); | |
| struct drm_display_mode *mode = &icn->mode; | |
| const struct drm_bridge_state *bridge_state; | |
| u16 hfp, hbp, hsync; | |
| u32 bus_flags; | |
| u8 pol, sys_ctrl_1, id[4]; | |
| chipone_readb(icn, VENDOR_ID, id); | |
| chipone_readb(icn, DEVICE_ID_H, id + 1); | |
| chipone_readb(icn, DEVICE_ID_L, id + 2); | |
| chipone_readb(icn, VERSION_ID, id + 3); | |
| dev_dbg(icn->dev, | |
| "Chip IDs: Vendor=0x%02x Device=0x%02x:0x%02x Version=0x%02x\n", | |
| id[0], id[1], id[2], id[3]); | |
| if (id[0] != 0xc1 || id[1] != 0x62 || id[2] != 0x11) { | |
| dev_dbg(icn->dev, "Invalid Chip IDs, aborting configuration\n"); | |
| return; | |
| } | |
| /* Get the DPI flags from the bridge state. */ | |
| bridge_state = drm_atomic_get_new_bridge_state(state, bridge); | |
| bus_flags = bridge_state->output_bus_cfg.flags; | |
| if (icn->interface_i2c) | |
| chipone_writeb(icn, MIPI_CFG_PW, MIPI_CFG_PW_CONFIG_I2C); | |
| else | |
| chipone_writeb(icn, MIPI_CFG_PW, MIPI_CFG_PW_CONFIG_DSI); | |
| chipone_writeb(icn, HACTIVE_LI, mode->hdisplay & 0xff); | |
| chipone_writeb(icn, VACTIVE_LI, mode->vdisplay & 0xff); | |
| /* | |
| * lsb nibble: 2nd nibble of hdisplay | |
| * msb nibble: 2nd nibble of vdisplay | |
| */ | |
| chipone_writeb(icn, VACTIVE_HACTIVE_HI, | |
| ((mode->hdisplay >> 8) & 0xf) | | |
| (((mode->vdisplay >> 8) & 0xf) << 4)); | |
| hfp = mode->hsync_start - mode->hdisplay; | |
| hsync = mode->hsync_end - mode->hsync_start; | |
| hbp = mode->htotal - mode->hsync_end; | |
| chipone_writeb(icn, HFP_LI, hfp & 0xff); | |
| chipone_writeb(icn, HSYNC_LI, hsync & 0xff); | |
| chipone_writeb(icn, HBP_LI, hbp & 0xff); | |
| /* Top two bits of Horizontal Front porch/Sync/Back porch */ | |
| chipone_writeb(icn, HFP_HSW_HBP_HI, | |
| HFP_HSW_HBP_HI_HFP(hfp) | | |
| HFP_HSW_HBP_HI_HS(hsync) | | |
| HFP_HSW_HBP_HI_HBP(hbp)); | |
| chipone_writeb(icn, VFP, mode->vsync_start - mode->vdisplay); | |
| chipone_writeb(icn, VSYNC, mode->vsync_end - mode->vsync_start); | |
| chipone_writeb(icn, VBP, mode->vtotal - mode->vsync_end); | |
| /* dsi specific sequence */ | |
| chipone_writeb(icn, SYNC_EVENT_DLY, 0x80); | |
| chipone_writeb(icn, HFP_MIN, hfp & 0xff); | |
| /* DSI data lane count */ | |
| chipone_writeb(icn, DSI_CTRL, | |
| DSI_CTRL_UNKNOWN | DSI_CTRL_DSI_LANES(icn->dsi->lanes - 1)); | |
| chipone_writeb(icn, MIPI_PD_CK_LANE, 0xa0); | |
| chipone_writeb(icn, PLL_CTRL(12), 0xff); | |
| chipone_writeb(icn, MIPI_PN_SWAP, 0x00); | |
| /* DPI HS/VS/DE polarity */ | |
| pol = ((mode->flags & DRM_MODE_FLAG_PHSYNC) ? BIST_POL_HSYNC_POL : 0) | | |
| ((mode->flags & DRM_MODE_FLAG_PVSYNC) ? BIST_POL_VSYNC_POL : 0) | | |
| ((bus_flags & DRM_BUS_FLAG_DE_HIGH) ? BIST_POL_DE_POL : 0); | |
| chipone_writeb(icn, BIST_POL, pol); | |
| /* Configure PLL settings */ | |
| chipone_configure_pll(icn, mode); | |
| chipone_writeb(icn, SYS_CTRL(0), 0x40); | |
| sys_ctrl_1 = 0x88; | |
| if (bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE) | |
| sys_ctrl_1 |= FIELD_PREP(SYS_CTRL_1_CLK_PHASE_MSK, CLK_PHASE_0); | |
| else | |
| sys_ctrl_1 |= FIELD_PREP(SYS_CTRL_1_CLK_PHASE_MSK, CLK_PHASE_1_2); | |
| chipone_writeb(icn, SYS_CTRL(1), sys_ctrl_1); | |
| /* icn6211 specific sequence */ | |
| chipone_writeb(icn, MIPI_FORCE_0, 0x20); | |
| chipone_writeb(icn, PLL_CTRL(1), 0x20); | |
| chipone_writeb(icn, CONFIG_FINISH, 0x10); | |
| usleep_range(10000, 11000); | |
| } | |
| static void chipone_atomic_pre_enable(struct drm_bridge *bridge, | |
| struct drm_atomic_commit *state) | |
| { | |
| struct chipone *icn = bridge_to_chipone(bridge); | |
| int ret; | |
| if (icn->vdd1) { | |
| ret = regulator_enable(icn->vdd1); | |
| if (ret) | |
| DRM_DEV_ERROR(icn->dev, | |
| "failed to enable VDD1 regulator: %d\n", ret); | |
| } | |
| if (icn->vdd2) { | |
| ret = regulator_enable(icn->vdd2); | |
| if (ret) | |
| DRM_DEV_ERROR(icn->dev, | |
| "failed to enable VDD2 regulator: %d\n", ret); | |
| } | |
| if (icn->vdd3) { | |
| ret = regulator_enable(icn->vdd3); | |
| if (ret) | |
| DRM_DEV_ERROR(icn->dev, | |
| "failed to enable VDD3 regulator: %d\n", ret); | |
| } | |
| ret = clk_prepare_enable(icn->refclk); | |
| if (ret) | |
| DRM_DEV_ERROR(icn->dev, | |
| "failed to enable RECLK clock: %d\n", ret); | |
| gpiod_set_value(icn->enable_gpio, 1); | |
| usleep_range(10000, 11000); | |
| } | |
| static void chipone_atomic_post_disable(struct drm_bridge *bridge, | |
| struct drm_atomic_commit *state) | |
| { | |
| struct chipone *icn = bridge_to_chipone(bridge); | |
| clk_disable_unprepare(icn->refclk); | |
| if (icn->vdd1) | |
| regulator_disable(icn->vdd1); | |
| if (icn->vdd2) | |
| regulator_disable(icn->vdd2); | |
| if (icn->vdd3) | |
| regulator_disable(icn->vdd3); | |
| gpiod_set_value(icn->enable_gpio, 0); | |
| } | |
| static void chipone_mode_set(struct drm_bridge *bridge, | |
| const struct drm_display_mode *mode, | |
| const struct drm_display_mode *adjusted_mode) | |
| { | |
| struct chipone *icn = bridge_to_chipone(bridge); | |
| drm_mode_copy(&icn->mode, adjusted_mode); | |
| }; | |
| static int chipone_dsi_attach(struct chipone *icn) | |
| { | |
| struct mipi_dsi_device *dsi = icn->dsi; | |
| struct device *dev = icn->dev; | |
| int dsi_lanes, ret; | |
| dsi_lanes = drm_of_get_data_lanes_count_ep(dev->of_node, 0, 0, 1, 4); | |
| /* | |
| * If the 'data-lanes' property does not exist in DT or is invalid, | |
| * default to previously hard-coded behavior, which was 4 data lanes. | |
| */ | |
| if (dsi_lanes < 0) | |
| icn->dsi->lanes = 4; | |
| else | |
| icn->dsi->lanes = dsi_lanes; | |
| dsi->format = MIPI_DSI_FMT_RGB888; | |
| dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | | |
| MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET; | |
| dsi->hs_rate = 500000000; | |
| dsi->lp_rate = 16000000; | |
| ret = mipi_dsi_attach(dsi); | |
| if (ret < 0) | |
| dev_err(icn->dev, "failed to attach dsi\n"); | |
| return ret; | |
| } | |
| static int chipone_dsi_host_attach(struct chipone *icn) | |
| { | |
| struct device *dev = icn->dev; | |
| struct device_node *host_node; | |
| struct device_node *endpoint; | |
| struct mipi_dsi_device *dsi; | |
| struct mipi_dsi_host *host; | |
| int ret = 0; | |
| const struct mipi_dsi_device_info info = { | |
| .type = "chipone", | |
| .channel = 0, | |
| .node = NULL, | |
| }; | |
| endpoint = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0); | |
| host_node = of_graph_get_remote_port_parent(endpoint); | |
| of_node_put(endpoint); | |
| if (!host_node) | |
| return -EINVAL; | |
| host = of_find_mipi_dsi_host_by_node(host_node); | |
| of_node_put(host_node); | |
| if (!host) | |
| return dev_err_probe(dev, -EPROBE_DEFER, "failed to find dsi host\n"); | |
| dsi = mipi_dsi_device_register_full(host, &info); | |
| if (IS_ERR(dsi)) { | |
| return dev_err_probe(dev, PTR_ERR(dsi), | |
| "failed to create dsi device\n"); | |
| } | |
| icn->dsi = dsi; | |
| ret = chipone_dsi_attach(icn); | |
| if (ret < 0) | |
| mipi_dsi_device_unregister(dsi); | |
| return ret; | |
| } | |
| static int chipone_attach(struct drm_bridge *bridge, | |
| struct drm_encoder *encoder, | |
| enum drm_bridge_attach_flags flags) | |
| { | |
| struct chipone *icn = bridge_to_chipone(bridge); | |
| return drm_bridge_attach(encoder, icn->panel_bridge, bridge, flags); | |
| } | |
| #define MAX_INPUT_SEL_FORMATS 1 | |
| static u32 * | |
| chipone_atomic_get_input_bus_fmts(struct drm_bridge *bridge, | |
| struct drm_bridge_state *bridge_state, | |
| struct drm_crtc_state *crtc_state, | |
| struct drm_connector_state *conn_state, | |
| u32 output_fmt, | |
| unsigned int *num_input_fmts) | |
| { | |
| u32 *input_fmts; | |
| *num_input_fmts = 0; | |
| input_fmts = kcalloc(MAX_INPUT_SEL_FORMATS, sizeof(*input_fmts), | |
| GFP_KERNEL); | |
| if (!input_fmts) | |
| return NULL; | |
| /* This is the DSI-end bus format */ | |
| input_fmts[0] = MEDIA_BUS_FMT_RGB888_1X24; | |
| *num_input_fmts = 1; | |
| return input_fmts; | |
| } | |
| static const struct drm_bridge_funcs chipone_bridge_funcs = { | |
| .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state, | |
| .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state, | |
| .atomic_create_state = drm_atomic_helper_bridge_create_state, | |
| .atomic_pre_enable = chipone_atomic_pre_enable, | |
| .atomic_enable = chipone_atomic_enable, | |
| .atomic_post_disable = chipone_atomic_post_disable, | |
| .mode_set = chipone_mode_set, | |
| .attach = chipone_attach, | |
| .atomic_get_input_bus_fmts = chipone_atomic_get_input_bus_fmts, | |
| }; | |
| static int chipone_parse_dt(struct chipone *icn) | |
| { | |
| struct device *dev = icn->dev; | |
| int ret; | |
| icn->refclk = devm_clk_get_optional(dev, "refclk"); | |
| if (IS_ERR(icn->refclk)) { | |
| ret = PTR_ERR(icn->refclk); | |
| DRM_DEV_ERROR(dev, "failed to get REFCLK clock: %d\n", ret); | |
| return ret; | |
| } else if (icn->refclk) { | |
| icn->refclk_rate = clk_get_rate(icn->refclk); | |
| if (icn->refclk_rate < 10000000 || icn->refclk_rate > 154000000) { | |
| DRM_DEV_ERROR(dev, "REFCLK out of range: %ld Hz\n", | |
| icn->refclk_rate); | |
| return -EINVAL; | |
| } | |
| } | |
| icn->vdd1 = devm_regulator_get_optional(dev, "vdd1"); | |
| if (IS_ERR(icn->vdd1)) { | |
| ret = PTR_ERR(icn->vdd1); | |
| if (ret == -EPROBE_DEFER) | |
| return -EPROBE_DEFER; | |
| icn->vdd1 = NULL; | |
| DRM_DEV_DEBUG(dev, "failed to get VDD1 regulator: %d\n", ret); | |
| } | |
| icn->vdd2 = devm_regulator_get_optional(dev, "vdd2"); | |
| if (IS_ERR(icn->vdd2)) { | |
| ret = PTR_ERR(icn->vdd2); | |
| if (ret == -EPROBE_DEFER) | |
| return -EPROBE_DEFER; | |
| icn->vdd2 = NULL; | |
| DRM_DEV_DEBUG(dev, "failed to get VDD2 regulator: %d\n", ret); | |
| } | |
| icn->vdd3 = devm_regulator_get_optional(dev, "vdd3"); | |
| if (IS_ERR(icn->vdd3)) { | |
| ret = PTR_ERR(icn->vdd3); | |
| if (ret == -EPROBE_DEFER) | |
| return -EPROBE_DEFER; | |
| icn->vdd3 = NULL; | |
| DRM_DEV_DEBUG(dev, "failed to get VDD3 regulator: %d\n", ret); | |
| } | |
| icn->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW); | |
| if (IS_ERR(icn->enable_gpio)) { | |
| DRM_DEV_ERROR(dev, "failed to get enable GPIO\n"); | |
| return PTR_ERR(icn->enable_gpio); | |
| } | |
| icn->panel_bridge = devm_drm_of_get_bridge(dev, dev->of_node, 1, 0); | |
| if (IS_ERR(icn->panel_bridge)) | |
| return PTR_ERR(icn->panel_bridge); | |
| return 0; | |
| } | |
| static int chipone_common_probe(struct device *dev, struct chipone **icnr) | |
| { | |
| struct chipone *icn; | |
| int ret; | |
| icn = devm_drm_bridge_alloc(dev, struct chipone, bridge, | |
| &chipone_bridge_funcs); | |
| if (IS_ERR(icn)) | |
| return PTR_ERR(icn); | |
| icn->dev = dev; | |
| ret = chipone_parse_dt(icn); | |
| if (ret) | |
| return ret; | |
| icn->bridge.type = DRM_MODE_CONNECTOR_DPI; | |
| icn->bridge.of_node = dev->of_node; | |
| *icnr = icn; | |
| return ret; | |
| } | |
| static int chipone_dsi_probe(struct mipi_dsi_device *dsi) | |
| { | |
| struct device *dev = &dsi->dev; | |
| struct chipone *icn; | |
| int ret; | |
| ret = chipone_common_probe(dev, &icn); | |
| if (ret) | |
| return ret; | |
| icn->regmap = devm_regmap_init(dev, &chipone_dsi_regmap_bus, | |
| dsi, &chipone_regmap_config); | |
| if (IS_ERR(icn->regmap)) | |
| return PTR_ERR(icn->regmap); | |
| icn->interface_i2c = false; | |
| icn->dsi = dsi; | |
| mipi_dsi_set_drvdata(dsi, icn); | |
| ret = devm_drm_bridge_add(dev, &icn->bridge); | |
| if (ret) | |
| return ret; | |
| return chipone_dsi_attach(icn); | |
| } | |
| static int chipone_i2c_probe(struct i2c_client *client) | |
| { | |
| struct device *dev = &client->dev; | |
| struct chipone *icn; | |
| int ret; | |
| ret = chipone_common_probe(dev, &icn); | |
| if (ret) | |
| return ret; | |
| icn->regmap = devm_regmap_init_i2c(client, &chipone_regmap_config); | |
| if (IS_ERR(icn->regmap)) | |
| return PTR_ERR(icn->regmap); | |
| icn->interface_i2c = true; | |
| icn->client = client; | |
| dev_set_drvdata(dev, icn); | |
| i2c_set_clientdata(client, icn); | |
| ret = devm_drm_bridge_add(dev, &icn->bridge); | |
| if (ret) | |
| return ret; | |
| return chipone_dsi_host_attach(icn); | |
| } | |
| static void chipone_dsi_remove(struct mipi_dsi_device *dsi) | |
| { | |
| mipi_dsi_detach(dsi); | |
| } | |
| static const struct of_device_id chipone_of_match[] = { | |
| { .compatible = "chipone,icn6211", }, | |
| { /* sentinel */ } | |
| }; | |
| MODULE_DEVICE_TABLE(of, chipone_of_match); | |
| static struct mipi_dsi_driver chipone_dsi_driver = { | |
| .probe = chipone_dsi_probe, | |
| .remove = chipone_dsi_remove, | |
| .driver = { | |
| .name = "chipone-icn6211", | |
| .of_match_table = chipone_of_match, | |
| }, | |
| }; | |
| static const struct i2c_device_id chipone_i2c_id[] = { | |
| { .name = "chipone,icn6211" }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, chipone_i2c_id); | |
| static struct i2c_driver chipone_i2c_driver = { | |
| .probe = chipone_i2c_probe, | |
| .id_table = chipone_i2c_id, | |
| .driver = { | |
| .name = "chipone-icn6211-i2c", | |
| .of_match_table = chipone_of_match, | |
| }, | |
| }; | |
| static int __init chipone_init(void) | |
| { | |
| if (IS_ENABLED(CONFIG_DRM_MIPI_DSI)) | |
| mipi_dsi_driver_register(&chipone_dsi_driver); | |
| return i2c_add_driver(&chipone_i2c_driver); | |
| } | |
| module_init(chipone_init); | |
| static void __exit chipone_exit(void) | |
| { | |
| i2c_del_driver(&chipone_i2c_driver); | |
| if (IS_ENABLED(CONFIG_DRM_MIPI_DSI)) | |
| mipi_dsi_driver_unregister(&chipone_dsi_driver); | |
| } | |
| module_exit(chipone_exit); | |
| MODULE_AUTHOR("Jagan Teki <jagan@amarulasolutions.com>"); | |
| MODULE_DESCRIPTION("Chipone ICN6211 MIPI-DSI to RGB Converter Bridge"); | |
| MODULE_LICENSE("GPL"); |