| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * gpio-max3191x.c - GPIO driver for Maxim MAX3191x industrial serializer | |
| * | |
| * Copyright (C) 2017 KUNBUS GmbH | |
| * | |
| * The MAX3191x makes 8 digital 24V inputs available via SPI. | |
| * Multiple chips can be daisy-chained, the spec does not impose | |
| * a limit on the number of chips and neither does this driver. | |
| * | |
| * Either of two modes is selectable: In 8-bit mode, only the state | |
| * of the inputs is clocked out to achieve high readout speeds; | |
| * In 16-bit mode, an additional status byte is clocked out with | |
| * a CRC and indicator bits for undervoltage and overtemperature. | |
| * The driver returns an error instead of potentially bogus data | |
| * if any of these fault conditions occur. However it does allow | |
| * readout of non-faulting chips in the same daisy-chain. | |
| * | |
| * MAX3191x supports four debounce settings and the driver is | |
| * capable of configuring these differently for each chip in the | |
| * daisy-chain. | |
| * | |
| * If the chips are hardwired to 8-bit mode ("modesel" pulled high), | |
| * gpio-pisosr.c can be used alternatively to this driver. | |
| * | |
| * https://datasheets.maximintegrated.com/en/ds/MAX31910.pdf | |
| * https://datasheets.maximintegrated.com/en/ds/MAX31911.pdf | |
| * https://datasheets.maximintegrated.com/en/ds/MAX31912.pdf | |
| * https://datasheets.maximintegrated.com/en/ds/MAX31913.pdf | |
| * https://datasheets.maximintegrated.com/en/ds/MAX31953-MAX31963.pdf | |
| */ | |
| #include <linux/bitmap.h> | |
| #include <linux/bitops.h> | |
| #include <linux/crc8.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/gpio/driver.h> | |
| #include <linux/module.h> | |
| #include <linux/spi/spi.h> | |
| enum max3191x_mode { | |
| STATUS_BYTE_ENABLED, | |
| STATUS_BYTE_DISABLED, | |
| }; | |
| /** | |
| * struct max3191x_chip - max3191x daisy-chain | |
| * @gpio: GPIO controller struct | |
| * @lock: protects read sequences | |
| * @nchips: number of chips in the daisy-chain | |
| * @mode: current mode, 0 for 16-bit, 1 for 8-bit; | |
| * for simplicity, all chips in the daisy-chain are assumed | |
| * to use the same mode | |
| * @modesel_pins: GPIO pins to configure modesel of each chip | |
| * @fault_pins: GPIO pins to detect fault of each chip | |
| * @db0_pins: GPIO pins to configure debounce of each chip | |
| * @db1_pins: GPIO pins to configure debounce of each chip | |
| * @mesg: SPI message to perform a readout | |
| * @xfer: SPI transfer used by @mesg | |
| * @crc_error: bitmap signaling CRC error for each chip | |
| * @overtemp: bitmap signaling overtemperature alarm for each chip | |
| * @undervolt1: bitmap signaling undervoltage alarm for each chip | |
| * @undervolt2: bitmap signaling undervoltage warning for each chip | |
| * @fault: bitmap signaling assertion of @fault_pins for each chip | |
| * @ignore_uv: whether to ignore undervoltage alarms; | |
| * set by a device property if the chips are powered through | |
| * 5VOUT instead of VCC24V, in which case they will constantly | |
| * signal undervoltage; | |
| * for simplicity, all chips in the daisy-chain are assumed | |
| * to be powered the same way | |
| */ | |
| struct max3191x_chip { | |
| struct gpio_chip gpio; | |
| struct mutex lock; | |
| u32 nchips; | |
| enum max3191x_mode mode; | |
| struct gpio_descs *modesel_pins; | |
| struct gpio_descs *fault_pins; | |
| struct gpio_descs *db0_pins; | |
| struct gpio_descs *db1_pins; | |
| struct spi_message mesg; | |
| struct spi_transfer xfer; | |
| unsigned long *crc_error; | |
| unsigned long *overtemp; | |
| unsigned long *undervolt1; | |
| unsigned long *undervolt2; | |
| unsigned long *fault; | |
| bool ignore_uv; | |
| }; | |
| #define MAX3191X_NGPIO 8 | |
| #define MAX3191X_CRC8_POLYNOMIAL 0xa8 /* (x^5) + x^4 + x^2 + x^0 */ | |
| DECLARE_CRC8_TABLE(max3191x_crc8); | |
| static int max3191x_get_direction(struct gpio_chip *gpio, unsigned int offset) | |
| { | |
| return GPIO_LINE_DIRECTION_IN; /* always in */ | |
| } | |
| static int max3191x_direction_input(struct gpio_chip *gpio, unsigned int offset) | |
| { | |
| return 0; | |
| } | |
| static unsigned int max3191x_wordlen(struct max3191x_chip *max3191x) | |
| { | |
| return max3191x->mode == STATUS_BYTE_ENABLED ? 2 : 1; | |
| } | |
| static int max3191x_readout_locked(struct max3191x_chip *max3191x) | |
| { | |
| struct device *dev = max3191x->gpio.parent; | |
| struct spi_device *spi = to_spi_device(dev); | |
| int val, i, ot = 0, uv1 = 0; | |
| val = spi_sync(spi, &max3191x->mesg); | |
| if (val) { | |
| dev_err_ratelimited(dev, "SPI receive error %d\n", val); | |
| return val; | |
| } | |
| for (i = 0; i < max3191x->nchips; i++) { | |
| if (max3191x->mode == STATUS_BYTE_ENABLED) { | |
| u8 in = ((u8 *)max3191x->xfer.rx_buf)[i * 2]; | |
| u8 status = ((u8 *)max3191x->xfer.rx_buf)[i * 2 + 1]; | |
| val = (status & 0xf8) != crc8(max3191x_crc8, &in, 1, 0); | |
| __assign_bit(i, max3191x->crc_error, val); | |
| if (val) | |
| dev_err_ratelimited(dev, | |
| "chip %d: CRC error\n", i); | |
| ot = (status >> 1) & 1; | |
| __assign_bit(i, max3191x->overtemp, ot); | |
| if (ot) | |
| dev_err_ratelimited(dev, | |
| "chip %d: overtemperature\n", i); | |
| if (!max3191x->ignore_uv) { | |
| uv1 = !((status >> 2) & 1); | |
| __assign_bit(i, max3191x->undervolt1, uv1); | |
| if (uv1) | |
| dev_err_ratelimited(dev, | |
| "chip %d: undervoltage\n", i); | |
| val = !(status & 1); | |
| __assign_bit(i, max3191x->undervolt2, val); | |
| if (val && !uv1) | |
| dev_warn_ratelimited(dev, | |
| "chip %d: voltage warn\n", i); | |
| } | |
| } | |
| if (max3191x->fault_pins && !max3191x->ignore_uv) { | |
| /* fault pin shared by all chips or per chip */ | |
| struct gpio_desc *fault_pin = | |
| (max3191x->fault_pins->ndescs == 1) | |
| ? max3191x->fault_pins->desc[0] | |
| : max3191x->fault_pins->desc[i]; | |
| val = gpiod_get_value_cansleep(fault_pin); | |
| if (val < 0) { | |
| dev_err_ratelimited(dev, | |
| "GPIO read error %d\n", val); | |
| return val; | |
| } | |
| __assign_bit(i, max3191x->fault, val); | |
| if (val && !uv1 && !ot) | |
| dev_err_ratelimited(dev, | |
| "chip %d: fault\n", i); | |
| } | |
| } | |
| return 0; | |
| } | |
| static bool max3191x_chip_is_faulting(struct max3191x_chip *max3191x, | |
| unsigned int chipnum) | |
| { | |
| /* without status byte the only diagnostic is the fault pin */ | |
| if (!max3191x->ignore_uv && test_bit(chipnum, max3191x->fault)) | |
| return true; | |
| if (max3191x->mode == STATUS_BYTE_DISABLED) | |
| return false; | |
| return test_bit(chipnum, max3191x->crc_error) || | |
| test_bit(chipnum, max3191x->overtemp) || | |
| (!max3191x->ignore_uv && | |
| test_bit(chipnum, max3191x->undervolt1)); | |
| } | |
| static int max3191x_get(struct gpio_chip *gpio, unsigned int offset) | |
| { | |
| struct max3191x_chip *max3191x = gpiochip_get_data(gpio); | |
| int ret, chipnum, wordlen = max3191x_wordlen(max3191x); | |
| u8 in; | |
| mutex_lock(&max3191x->lock); | |
| ret = max3191x_readout_locked(max3191x); | |
| if (ret) | |
| goto out_unlock; | |
| chipnum = offset / MAX3191X_NGPIO; | |
| if (max3191x_chip_is_faulting(max3191x, chipnum)) { | |
| ret = -EIO; | |
| goto out_unlock; | |
| } | |
| in = ((u8 *)max3191x->xfer.rx_buf)[chipnum * wordlen]; | |
| ret = (in >> (offset % MAX3191X_NGPIO)) & 1; | |
| out_unlock: | |
| mutex_unlock(&max3191x->lock); | |
| return ret; | |
| } | |
| static int max3191x_get_multiple(struct gpio_chip *gpio, unsigned long *mask, | |
| unsigned long *bits) | |
| { | |
| struct max3191x_chip *max3191x = gpiochip_get_data(gpio); | |
| const unsigned int wordlen = max3191x_wordlen(max3191x); | |
| int ret; | |
| unsigned long bit; | |
| unsigned long gpio_mask; | |
| unsigned long in; | |
| mutex_lock(&max3191x->lock); | |
| ret = max3191x_readout_locked(max3191x); | |
| if (ret) | |
| goto out_unlock; | |
| bitmap_zero(bits, gpio->ngpio); | |
| for_each_set_clump8(bit, gpio_mask, mask, gpio->ngpio) { | |
| unsigned int chipnum = bit / MAX3191X_NGPIO; | |
| if (max3191x_chip_is_faulting(max3191x, chipnum)) { | |
| ret = -EIO; | |
| goto out_unlock; | |
| } | |
| in = ((u8 *)max3191x->xfer.rx_buf)[chipnum * wordlen]; | |
| in &= gpio_mask; | |
| bitmap_set_value8(bits, in, bit); | |
| } | |
| out_unlock: | |
| mutex_unlock(&max3191x->lock); | |
| return ret; | |
| } | |
| static int max3191x_set_config(struct gpio_chip *gpio, unsigned int offset, | |
| unsigned long config) | |
| { | |
| struct max3191x_chip *max3191x = gpiochip_get_data(gpio); | |
| u32 debounce, chipnum, db0_val, db1_val; | |
| if (pinconf_to_config_param(config) != PIN_CONFIG_INPUT_DEBOUNCE) | |
| return -ENOTSUPP; | |
| if (!max3191x->db0_pins || !max3191x->db1_pins) | |
| return -EINVAL; | |
| debounce = pinconf_to_config_argument(config); | |
| switch (debounce) { | |
| case 0: | |
| db0_val = 0; | |
| db1_val = 0; | |
| break; | |
| case 1 ... 25: | |
| db0_val = 0; | |
| db1_val = 1; | |
| break; | |
| case 26 ... 750: | |
| db0_val = 1; | |
| db1_val = 0; | |
| break; | |
| case 751 ... 3000: | |
| db0_val = 1; | |
| db1_val = 1; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| if (max3191x->db0_pins->ndescs == 1) | |
| chipnum = 0; /* all chips use the same pair of debounce pins */ | |
| else | |
| chipnum = offset / MAX3191X_NGPIO; /* per chip debounce pins */ | |
| mutex_lock(&max3191x->lock); | |
| gpiod_set_value_cansleep(max3191x->db0_pins->desc[chipnum], db0_val); | |
| gpiod_set_value_cansleep(max3191x->db1_pins->desc[chipnum], db1_val); | |
| mutex_unlock(&max3191x->lock); | |
| return 0; | |
| } | |
| static void max3191x_gpiod_multi_set_single_value(struct gpio_descs *descs, | |
| int value) | |
| { | |
| unsigned long *values; | |
| values = bitmap_alloc(descs->ndescs, GFP_KERNEL); | |
| if (!values) | |
| return; | |
| if (value) | |
| bitmap_fill(values, descs->ndescs); | |
| else | |
| bitmap_zero(values, descs->ndescs); | |
| gpiod_multi_set_value_cansleep(descs, values); | |
| bitmap_free(values); | |
| } | |
| static struct gpio_descs *devm_gpiod_get_array_optional_count( | |
| struct device *dev, const char *con_id, | |
| enum gpiod_flags flags, unsigned int expected) | |
| { | |
| struct gpio_descs *descs; | |
| int found = gpiod_count(dev, con_id); | |
| if (found == -ENOENT) | |
| return NULL; | |
| if (found != expected && found != 1) { | |
| dev_err(dev, "ignoring %s-gpios: found %d, expected %u or 1\n", | |
| con_id, found, expected); | |
| return NULL; | |
| } | |
| descs = devm_gpiod_get_array_optional(dev, con_id, flags); | |
| if (IS_ERR(descs)) { | |
| dev_err(dev, "failed to get %s-gpios: %ld\n", | |
| con_id, PTR_ERR(descs)); | |
| return NULL; | |
| } | |
| return descs; | |
| } | |
| static int max3191x_probe(struct spi_device *spi) | |
| { | |
| struct device *dev = &spi->dev; | |
| struct max3191x_chip *max3191x; | |
| int n, ret; | |
| max3191x = devm_kzalloc(dev, sizeof(*max3191x), GFP_KERNEL); | |
| if (!max3191x) | |
| return -ENOMEM; | |
| spi_set_drvdata(spi, max3191x); | |
| max3191x->nchips = 1; | |
| device_property_read_u32(dev, "#daisy-chained-devices", | |
| &max3191x->nchips); | |
| n = BITS_TO_LONGS(max3191x->nchips); | |
| max3191x->crc_error = devm_kcalloc(dev, n, sizeof(long), GFP_KERNEL); | |
| max3191x->undervolt1 = devm_kcalloc(dev, n, sizeof(long), GFP_KERNEL); | |
| max3191x->undervolt2 = devm_kcalloc(dev, n, sizeof(long), GFP_KERNEL); | |
| max3191x->overtemp = devm_kcalloc(dev, n, sizeof(long), GFP_KERNEL); | |
| max3191x->fault = devm_kcalloc(dev, n, sizeof(long), GFP_KERNEL); | |
| max3191x->xfer.rx_buf = devm_kcalloc(dev, max3191x->nchips, | |
| 2, GFP_KERNEL); | |
| if (!max3191x->crc_error || !max3191x->undervolt1 || | |
| !max3191x->overtemp || !max3191x->undervolt2 || | |
| !max3191x->fault || !max3191x->xfer.rx_buf) | |
| return -ENOMEM; | |
| max3191x->modesel_pins = devm_gpiod_get_array_optional_count(dev, | |
| "maxim,modesel", GPIOD_ASIS, max3191x->nchips); | |
| max3191x->fault_pins = devm_gpiod_get_array_optional_count(dev, | |
| "maxim,fault", GPIOD_IN, max3191x->nchips); | |
| max3191x->db0_pins = devm_gpiod_get_array_optional_count(dev, | |
| "maxim,db0", GPIOD_OUT_LOW, max3191x->nchips); | |
| max3191x->db1_pins = devm_gpiod_get_array_optional_count(dev, | |
| "maxim,db1", GPIOD_OUT_LOW, max3191x->nchips); | |
| max3191x->mode = device_property_read_bool(dev, "maxim,modesel-8bit") | |
| ? STATUS_BYTE_DISABLED : STATUS_BYTE_ENABLED; | |
| if (max3191x->modesel_pins) | |
| max3191x_gpiod_multi_set_single_value(max3191x->modesel_pins, | |
| max3191x->mode); | |
| max3191x->ignore_uv = device_property_read_bool(dev, | |
| "maxim,ignore-undervoltage"); | |
| if (max3191x->db0_pins && max3191x->db1_pins && | |
| max3191x->db0_pins->ndescs != max3191x->db1_pins->ndescs) { | |
| dev_err(dev, "ignoring maxim,db*-gpios: array len mismatch\n"); | |
| devm_gpiod_put_array(dev, max3191x->db0_pins); | |
| devm_gpiod_put_array(dev, max3191x->db1_pins); | |
| max3191x->db0_pins = NULL; | |
| max3191x->db1_pins = NULL; | |
| } | |
| max3191x->xfer.len = max3191x->nchips * max3191x_wordlen(max3191x); | |
| spi_message_init_with_transfers(&max3191x->mesg, &max3191x->xfer, 1); | |
| max3191x->gpio.label = spi->modalias; | |
| max3191x->gpio.owner = THIS_MODULE; | |
| max3191x->gpio.parent = dev; | |
| max3191x->gpio.base = -1; | |
| max3191x->gpio.ngpio = max3191x->nchips * MAX3191X_NGPIO; | |
| max3191x->gpio.can_sleep = true; | |
| max3191x->gpio.get_direction = max3191x_get_direction; | |
| max3191x->gpio.direction_input = max3191x_direction_input; | |
| max3191x->gpio.get = max3191x_get; | |
| max3191x->gpio.get_multiple = max3191x_get_multiple; | |
| max3191x->gpio.set_config = max3191x_set_config; | |
| mutex_init(&max3191x->lock); | |
| ret = gpiochip_add_data(&max3191x->gpio, max3191x); | |
| if (ret) { | |
| mutex_destroy(&max3191x->lock); | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static void max3191x_remove(struct spi_device *spi) | |
| { | |
| struct max3191x_chip *max3191x = spi_get_drvdata(spi); | |
| gpiochip_remove(&max3191x->gpio); | |
| mutex_destroy(&max3191x->lock); | |
| } | |
| static int __init max3191x_register_driver(struct spi_driver *sdrv) | |
| { | |
| crc8_populate_msb(max3191x_crc8, MAX3191X_CRC8_POLYNOMIAL); | |
| return spi_register_driver(sdrv); | |
| } | |
| static const struct of_device_id max3191x_of_id[] = { | |
| { .compatible = "maxim,max31910" }, | |
| { .compatible = "maxim,max31911" }, | |
| { .compatible = "maxim,max31912" }, | |
| { .compatible = "maxim,max31913" }, | |
| { .compatible = "maxim,max31953" }, | |
| { .compatible = "maxim,max31963" }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(of, max3191x_of_id); | |
| static const struct spi_device_id max3191x_spi_id[] = { | |
| { "max31910" }, | |
| { "max31911" }, | |
| { "max31912" }, | |
| { "max31913" }, | |
| { "max31953" }, | |
| { "max31963" }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(spi, max3191x_spi_id); | |
| static struct spi_driver max3191x_driver = { | |
| .driver = { | |
| .name = "max3191x", | |
| .of_match_table = max3191x_of_id, | |
| }, | |
| .probe = max3191x_probe, | |
| .remove = max3191x_remove, | |
| .id_table = max3191x_spi_id, | |
| }; | |
| module_driver(max3191x_driver, max3191x_register_driver, spi_unregister_driver); | |
| MODULE_AUTHOR("Lukas Wunner <lukas@wunner.de>"); | |
| MODULE_DESCRIPTION("GPIO driver for Maxim MAX3191x industrial serializer"); | |
| MODULE_LICENSE("GPL v2"); |