| // SPDX-License-Identifier: GPL-2.0-only | |
| /* | |
| * Copyright (C) 2015 Xilinx, Inc. | |
| * CEVA AHCI SATA platform driver | |
| * | |
| * based on the AHCI SATA platform driver by Jeff Garzik and Anton Vorontsov | |
| */ | |
| #include <linux/ahci_platform.h> | |
| #include <linux/kernel.h> | |
| #include <linux/libata.h> | |
| #include <linux/module.h> | |
| #include <linux/of.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/reset.h> | |
| #include "ahci.h" | |
| /* Vendor Specific Register Offsets */ | |
| #define AHCI_VEND_PCFG 0xA4 | |
| #define AHCI_VEND_PPCFG 0xA8 | |
| #define AHCI_VEND_PP2C 0xAC | |
| #define AHCI_VEND_PP3C 0xB0 | |
| #define AHCI_VEND_PP4C 0xB4 | |
| #define AHCI_VEND_PP5C 0xB8 | |
| #define AHCI_VEND_AXICC 0xBC | |
| #define AHCI_VEND_PAXIC 0xC0 | |
| #define AHCI_VEND_PTC 0xC8 | |
| /* Vendor Specific Register bit definitions */ | |
| #define PAXIC_ADBW_BW64 0x1 | |
| #define PAXIC_MAWID(i) (((i) * 2) << 4) | |
| #define PAXIC_MARID(i) (((i) * 2) << 12) | |
| #define PAXIC_MARIDD(i) ((((i) * 2) + 1) << 16) | |
| #define PAXIC_MAWIDD(i) ((((i) * 2) + 1) << 8) | |
| #define PAXIC_OTL (0x4 << 20) | |
| /* Register bit definitions for cache control */ | |
| #define AXICC_ARCA_VAL (0xF << 0) | |
| #define AXICC_ARCF_VAL (0xF << 4) | |
| #define AXICC_ARCH_VAL (0xF << 8) | |
| #define AXICC_ARCP_VAL (0xF << 12) | |
| #define AXICC_AWCFD_VAL (0xF << 16) | |
| #define AXICC_AWCD_VAL (0xF << 20) | |
| #define AXICC_AWCF_VAL (0xF << 24) | |
| #define PCFG_TPSS_VAL (0x32 << 16) | |
| #define PCFG_TPRS_VAL (0x2 << 12) | |
| #define PCFG_PAD_VAL 0x2 | |
| #define PPCFG_TTA 0x1FFFE | |
| #define PPCFG_PSSO_EN (1 << 28) | |
| #define PPCFG_PSS_EN (1 << 29) | |
| #define PPCFG_ESDF_EN (1 << 31) | |
| #define PP5C_RIT 0x60216 | |
| #define PP5C_RCT (0x7f0 << 20) | |
| #define PTC_RX_WM_VAL 0x40 | |
| #define PTC_RSVD (1 << 27) | |
| #define PORT0_BASE 0x100 | |
| #define PORT1_BASE 0x180 | |
| /* Port Control Register Bit Definitions */ | |
| #define PORT_SCTL_SPD_GEN3 (0x3 << 4) | |
| #define PORT_SCTL_SPD_GEN2 (0x2 << 4) | |
| #define PORT_SCTL_SPD_GEN1 (0x1 << 4) | |
| #define PORT_SCTL_IPM (0x3 << 8) | |
| #define PORT_BASE 0x100 | |
| #define PORT_OFFSET 0x80 | |
| #define NR_PORTS 2 | |
| #define DRV_NAME "ahci-ceva" | |
| #define CEVA_FLAG_BROKEN_GEN2 1 | |
| static unsigned int rx_watermark = PTC_RX_WM_VAL; | |
| module_param(rx_watermark, uint, 0644); | |
| MODULE_PARM_DESC(rx_watermark, "RxWaterMark value (0 - 0x80)"); | |
| struct ceva_ahci_priv { | |
| struct platform_device *ahci_pdev; | |
| /* Port Phy2Cfg Register */ | |
| u32 pp2c[NR_PORTS]; | |
| u32 pp3c[NR_PORTS]; | |
| u32 pp4c[NR_PORTS]; | |
| u32 pp5c[NR_PORTS]; | |
| /* Axi Cache Control Register */ | |
| u32 axicc; | |
| bool is_cci_enabled; | |
| int flags; | |
| }; | |
| static unsigned int ceva_ahci_read_id(struct ata_device *dev, | |
| struct ata_taskfile *tf, __le16 *id) | |
| { | |
| u32 err_mask; | |
| err_mask = ata_do_dev_read_id(dev, tf, id); | |
| if (err_mask) | |
| return err_mask; | |
| /* | |
| * Since CEVA controller does not support device sleep feature, we | |
| * need to clear DEVSLP (bit 8) in word78 of the IDENTIFY DEVICE data. | |
| */ | |
| id[ATA_ID_FEATURE_SUPP] &= cpu_to_le16(~(1 << 8)); | |
| return 0; | |
| } | |
| static struct ata_port_operations ahci_ceva_ops = { | |
| .inherits = &ahci_platform_ops, | |
| .read_id = ceva_ahci_read_id, | |
| }; | |
| static const struct ata_port_info ahci_ceva_port_info = { | |
| .flags = AHCI_FLAG_COMMON, | |
| .pio_mask = ATA_PIO4, | |
| .udma_mask = ATA_UDMA6, | |
| .port_ops = &ahci_ceva_ops, | |
| }; | |
| static void ahci_ceva_setup(struct ahci_host_priv *hpriv) | |
| { | |
| void __iomem *mmio = hpriv->mmio; | |
| struct ceva_ahci_priv *cevapriv = hpriv->plat_data; | |
| u32 tmp; | |
| int i; | |
| /* Set AHCI Enable */ | |
| tmp = readl(mmio + HOST_CTL); | |
| tmp |= HOST_AHCI_EN; | |
| writel(tmp, mmio + HOST_CTL); | |
| for (i = 0; i < NR_PORTS; i++) { | |
| /* TPSS TPRS scalars, CISE and Port Addr */ | |
| tmp = PCFG_TPSS_VAL | PCFG_TPRS_VAL | (PCFG_PAD_VAL + i); | |
| writel(tmp, mmio + AHCI_VEND_PCFG); | |
| /* | |
| * AXI Data bus width to 64 | |
| * Set Mem Addr Read, Write ID for data transfers | |
| * Set Mem Addr Read ID, Write ID for non-data transfers | |
| * Transfer limit to 72 DWord | |
| */ | |
| tmp = PAXIC_ADBW_BW64 | PAXIC_MAWIDD(i) | PAXIC_MARIDD(i) | | |
| PAXIC_MAWID(i) | PAXIC_MARID(i) | PAXIC_OTL; | |
| writel(tmp, mmio + AHCI_VEND_PAXIC); | |
| /* Set AXI cache control register if CCi is enabled */ | |
| if (cevapriv->is_cci_enabled) { | |
| tmp = readl(mmio + AHCI_VEND_AXICC); | |
| tmp |= AXICC_ARCA_VAL | AXICC_ARCF_VAL | | |
| AXICC_ARCH_VAL | AXICC_ARCP_VAL | | |
| AXICC_AWCFD_VAL | AXICC_AWCD_VAL | | |
| AXICC_AWCF_VAL; | |
| writel(tmp, mmio + AHCI_VEND_AXICC); | |
| } | |
| /* Port Phy Cfg register enables */ | |
| tmp = PPCFG_TTA | PPCFG_PSS_EN | PPCFG_ESDF_EN; | |
| writel(tmp, mmio + AHCI_VEND_PPCFG); | |
| /* Phy Control OOB timing parameters COMINIT */ | |
| writel(cevapriv->pp2c[i], mmio + AHCI_VEND_PP2C); | |
| /* Phy Control OOB timing parameters COMWAKE */ | |
| writel(cevapriv->pp3c[i], mmio + AHCI_VEND_PP3C); | |
| /* Phy Control Burst timing setting */ | |
| writel(cevapriv->pp4c[i], mmio + AHCI_VEND_PP4C); | |
| /* Rate Change Timer and Retry Interval Timer setting */ | |
| writel(cevapriv->pp5c[i], mmio + AHCI_VEND_PP5C); | |
| /* Rx Watermark setting */ | |
| tmp = rx_watermark | PTC_RSVD; | |
| writel(tmp, mmio + AHCI_VEND_PTC); | |
| /* Default to Gen 3 Speed and Gen 1 if Gen2 is broken */ | |
| tmp = PORT_SCTL_SPD_GEN3 | PORT_SCTL_IPM; | |
| if (cevapriv->flags & CEVA_FLAG_BROKEN_GEN2) | |
| tmp = PORT_SCTL_SPD_GEN1 | PORT_SCTL_IPM; | |
| writel(tmp, mmio + PORT_SCR_CTL + PORT_BASE + PORT_OFFSET * i); | |
| } | |
| } | |
| static const struct scsi_host_template ahci_platform_sht = { | |
| AHCI_SHT(DRV_NAME), | |
| }; | |
| static int ceva_ahci_platform_enable_resources(struct ahci_host_priv *hpriv) | |
| { | |
| int rc, i; | |
| rc = ahci_platform_enable_regulators(hpriv); | |
| if (rc) | |
| return rc; | |
| rc = ahci_platform_enable_clks(hpriv); | |
| if (rc) | |
| goto disable_regulator; | |
| /* Assert the controller reset */ | |
| rc = ahci_platform_assert_rsts(hpriv); | |
| if (rc) | |
| goto disable_clks; | |
| for (i = 0; i < hpriv->nports; i++) { | |
| if (ahci_ignore_port(hpriv, i)) | |
| continue; | |
| rc = phy_init(hpriv->phys[i]); | |
| if (rc) | |
| goto exit_phys; | |
| } | |
| /* De-assert the controller reset */ | |
| ahci_platform_deassert_rsts(hpriv); | |
| for (i = 0; i < hpriv->nports; i++) { | |
| if (ahci_ignore_port(hpriv, i)) | |
| continue; | |
| rc = phy_power_on(hpriv->phys[i]); | |
| if (rc) { | |
| phy_exit(hpriv->phys[i]); | |
| goto disable_phys; | |
| } | |
| } | |
| return 0; | |
| disable_phys: | |
| while (--i >= 0) { | |
| if (ahci_ignore_port(hpriv, i)) | |
| continue; | |
| phy_power_off(hpriv->phys[i]); | |
| phy_exit(hpriv->phys[i]); | |
| } | |
| ahci_platform_assert_rsts(hpriv); | |
| goto disable_clks; | |
| exit_phys: | |
| while (--i >= 0) { | |
| if (ahci_ignore_port(hpriv, i)) | |
| continue; | |
| phy_exit(hpriv->phys[i]); | |
| } | |
| disable_clks: | |
| ahci_platform_disable_clks(hpriv); | |
| disable_regulator: | |
| ahci_platform_disable_regulators(hpriv); | |
| return rc; | |
| } | |
| static int ceva_ahci_probe(struct platform_device *pdev) | |
| { | |
| struct device_node *np = pdev->dev.of_node; | |
| struct device *dev = &pdev->dev; | |
| struct ahci_host_priv *hpriv; | |
| struct ceva_ahci_priv *cevapriv; | |
| enum dev_dma_attr attr; | |
| int rc; | |
| cevapriv = devm_kzalloc(dev, sizeof(*cevapriv), GFP_KERNEL); | |
| if (!cevapriv) | |
| return -ENOMEM; | |
| cevapriv->ahci_pdev = pdev; | |
| hpriv = ahci_platform_get_resources(pdev, 0); | |
| if (IS_ERR(hpriv)) | |
| return PTR_ERR(hpriv); | |
| hpriv->rsts = devm_reset_control_get_optional_exclusive(&pdev->dev, | |
| NULL); | |
| if (IS_ERR(hpriv->rsts)) | |
| return dev_err_probe(&pdev->dev, PTR_ERR(hpriv->rsts), | |
| "failed to get reset\n"); | |
| rc = ceva_ahci_platform_enable_resources(hpriv); | |
| if (rc) | |
| return rc; | |
| if (of_property_read_bool(np, "ceva,broken-gen2")) | |
| cevapriv->flags = CEVA_FLAG_BROKEN_GEN2; | |
| /* Read OOB timing value for COMINIT from device-tree */ | |
| if (of_property_read_u8_array(np, "ceva,p0-cominit-params", | |
| (u8 *)&cevapriv->pp2c[0], 4) < 0) { | |
| dev_warn(dev, "ceva,p0-cominit-params property not defined\n"); | |
| rc = -EINVAL; | |
| goto disable_resources; | |
| } | |
| if (of_property_read_u8_array(np, "ceva,p1-cominit-params", | |
| (u8 *)&cevapriv->pp2c[1], 4) < 0) { | |
| dev_warn(dev, "ceva,p1-cominit-params property not defined\n"); | |
| rc = -EINVAL; | |
| goto disable_resources; | |
| } | |
| /* Read OOB timing value for COMWAKE from device-tree*/ | |
| if (of_property_read_u8_array(np, "ceva,p0-comwake-params", | |
| (u8 *)&cevapriv->pp3c[0], 4) < 0) { | |
| dev_warn(dev, "ceva,p0-comwake-params property not defined\n"); | |
| rc = -EINVAL; | |
| goto disable_resources; | |
| } | |
| if (of_property_read_u8_array(np, "ceva,p1-comwake-params", | |
| (u8 *)&cevapriv->pp3c[1], 4) < 0) { | |
| dev_warn(dev, "ceva,p1-comwake-params property not defined\n"); | |
| rc = -EINVAL; | |
| goto disable_resources; | |
| } | |
| /* Read phy BURST timing value from device-tree */ | |
| if (of_property_read_u8_array(np, "ceva,p0-burst-params", | |
| (u8 *)&cevapriv->pp4c[0], 4) < 0) { | |
| dev_warn(dev, "ceva,p0-burst-params property not defined\n"); | |
| rc = -EINVAL; | |
| goto disable_resources; | |
| } | |
| if (of_property_read_u8_array(np, "ceva,p1-burst-params", | |
| (u8 *)&cevapriv->pp4c[1], 4) < 0) { | |
| dev_warn(dev, "ceva,p1-burst-params property not defined\n"); | |
| rc = -EINVAL; | |
| goto disable_resources; | |
| } | |
| /* Read phy RETRY interval timing value from device-tree */ | |
| if (of_property_read_u16_array(np, "ceva,p0-retry-params", | |
| (u16 *)&cevapriv->pp5c[0], 2) < 0) { | |
| dev_warn(dev, "ceva,p0-retry-params property not defined\n"); | |
| rc = -EINVAL; | |
| goto disable_resources; | |
| } | |
| if (of_property_read_u16_array(np, "ceva,p1-retry-params", | |
| (u16 *)&cevapriv->pp5c[1], 2) < 0) { | |
| dev_warn(dev, "ceva,p1-retry-params property not defined\n"); | |
| rc = -EINVAL; | |
| goto disable_resources; | |
| } | |
| /* | |
| * Check if CCI is enabled for SATA. The DEV_DMA_COHERENT is returned | |
| * if CCI is enabled, so check for DEV_DMA_COHERENT. | |
| */ | |
| attr = device_get_dma_attr(dev); | |
| cevapriv->is_cci_enabled = (attr == DEV_DMA_COHERENT); | |
| hpriv->plat_data = cevapriv; | |
| /* CEVA specific initialization */ | |
| ahci_ceva_setup(hpriv); | |
| rc = ahci_platform_init_host(pdev, hpriv, &ahci_ceva_port_info, | |
| &ahci_platform_sht); | |
| if (rc) | |
| goto disable_resources; | |
| return 0; | |
| disable_resources: | |
| ahci_platform_disable_resources(hpriv); | |
| return rc; | |
| } | |
| static int __maybe_unused ceva_ahci_suspend(struct device *dev) | |
| { | |
| return ahci_platform_suspend(dev); | |
| } | |
| static int __maybe_unused ceva_ahci_resume(struct device *dev) | |
| { | |
| struct ata_host *host = dev_get_drvdata(dev); | |
| struct ahci_host_priv *hpriv = host->private_data; | |
| int rc; | |
| rc = ceva_ahci_platform_enable_resources(hpriv); | |
| if (rc) | |
| return rc; | |
| /* Configure CEVA specific config before resuming HBA */ | |
| ahci_ceva_setup(hpriv); | |
| rc = ahci_platform_resume_host(dev); | |
| if (rc) | |
| goto disable_resources; | |
| /* We resumed so update PM runtime state */ | |
| pm_runtime_disable(dev); | |
| pm_runtime_set_active(dev); | |
| pm_runtime_enable(dev); | |
| return 0; | |
| disable_resources: | |
| ahci_platform_disable_resources(hpriv); | |
| return rc; | |
| } | |
| static SIMPLE_DEV_PM_OPS(ahci_ceva_pm_ops, ceva_ahci_suspend, ceva_ahci_resume); | |
| static const struct of_device_id ceva_ahci_of_match[] = { | |
| { .compatible = "ceva,ahci-1v84" }, | |
| { /* sentinel */ } | |
| }; | |
| MODULE_DEVICE_TABLE(of, ceva_ahci_of_match); | |
| static struct platform_driver ceva_ahci_driver = { | |
| .probe = ceva_ahci_probe, | |
| .remove = ata_platform_remove_one, | |
| .driver = { | |
| .name = DRV_NAME, | |
| .of_match_table = ceva_ahci_of_match, | |
| .pm = &ahci_ceva_pm_ops, | |
| }, | |
| }; | |
| module_platform_driver(ceva_ahci_driver); | |
| MODULE_DESCRIPTION("CEVA AHCI SATA platform driver"); | |
| MODULE_AUTHOR("Xilinx Inc."); | |
| MODULE_LICENSE("GPL v2"); |