| # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) | |
| %YAML 1.2 | |
| --- | |
| $id: http://devicetree.org/schemas/usb/dwc3-xilinx.yaml# | |
| $schema: http://devicetree.org/meta-schemas/core.yaml# | |
| title: Xilinx SuperSpeed DWC3 USB SoC controller | |
| maintainers: | |
| - Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> | |
| properties: | |
| compatible: | |
| items: | |
| - enum: | |
| - xlnx,zynqmp-dwc3 | |
| - xlnx,versal-dwc3 | |
| reg: | |
| maxItems: 1 | |
| "#address-cells": | |
| enum: [ 1, 2 ] | |
| "#size-cells": | |
| enum: [ 1, 2 ] | |
| ranges: true | |
| dma-coherent: true | |
| power-domains: | |
| description: specifies a phandle to PM domain provider node | |
| maxItems: 1 | |
| clocks: | |
| description: | |
| A list of phandle and clock-specifier pairs for the clocks | |
| listed in clock-names. | |
| items: | |
| - description: Master/Core clock, has to be >= 125 MHz | |
| for SS operation and >= 60MHz for HS operation. | |
| - description: Clock source to core during PHY power down. | |
| clock-names: | |
| items: | |
| - const: bus_clk | |
| - const: ref_clk | |
| resets: | |
| minItems: 1 | |
| description: | |
| A list of phandles for resets listed in reset-names. | |
| items: | |
| - description: USB core reset | |
| - description: USB hibernation reset | |
| - description: USB APB reset | |
| reset-names: | |
| minItems: 1 | |
| items: | |
| - const: usb_crst | |
| - const: usb_hibrst | |
| - const: usb_apbrst | |
| phys: | |
| minItems: 1 | |
| maxItems: 2 | |
| phy-names: | |
| minItems: 1 | |
| maxItems: 2 | |
| items: | |
| enum: | |
| - usb2-phy | |
| - usb3-phy | |
| reset-gpios: | |
| description: GPIO used for the reset ulpi-phy | |
| maxItems: 1 | |
| # Required child node: | |
| patternProperties: | |
| "^usb@[0-9a-f]+$": | |
| $ref: snps,dwc3.yaml# | |
| required: | |
| - compatible | |
| - reg | |
| - "#address-cells" | |
| - "#size-cells" | |
| - ranges | |
| - power-domains | |
| - clocks | |
| - clock-names | |
| - resets | |
| - reset-names | |
| allOf: | |
| - if: | |
| properties: | |
| compatible: | |
| contains: | |
| enum: | |
| - xlnx,versal-dwc3 | |
| then: | |
| properties: | |
| resets: | |
| maxItems: 1 | |
| reset-names: | |
| maxItems: 1 | |
| else: | |
| properties: | |
| resets: | |
| minItems: 3 | |
| reset-names: | |
| minItems: 3 | |
| additionalProperties: false | |
| examples: | |
| - | | |
| #include <dt-bindings/dma/xlnx-zynqmp-dpdma.h> | |
| #include <dt-bindings/power/xlnx-zynqmp-power.h> | |
| #include <dt-bindings/reset/xlnx-zynqmp-resets.h> | |
| #include <dt-bindings/reset/xlnx-zynqmp-resets.h> | |
| #include <dt-bindings/phy/phy.h> | |
| axi { | |
| #address-cells = <2>; | |
| #size-cells = <2>; | |
| usb@0 { | |
| #address-cells = <0x2>; | |
| #size-cells = <0x2>; | |
| compatible = "xlnx,zynqmp-dwc3"; | |
| reg = <0x0 0xff9d0000 0x0 0x100>; | |
| clocks = <&zynqmp_clk 32>, <&zynqmp_clk 34>; | |
| clock-names = "bus_clk", "ref_clk"; | |
| power-domains = <&zynqmp_firmware PD_USB_0>; | |
| resets = <&zynqmp_reset ZYNQMP_RESET_USB1_CORERESET>, | |
| <&zynqmp_reset ZYNQMP_RESET_USB1_HIBERRESET>, | |
| <&zynqmp_reset ZYNQMP_RESET_USB1_APB>; | |
| reset-names = "usb_crst", "usb_hibrst", "usb_apbrst"; | |
| phys = <&psgtr 2 PHY_TYPE_USB3 0 2>; | |
| phy-names = "usb3-phy"; | |
| ranges; | |
| usb@fe200000 { | |
| compatible = "snps,dwc3"; | |
| reg = <0x0 0xfe200000 0x0 0x40000>; | |
| interrupt-names = "host", "otg"; | |
| interrupts = <0 65 4>, <0 69 4>; | |
| dr_mode = "host"; | |
| dma-coherent; | |
| }; | |
| }; | |
| }; |