| # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) | |
| %YAML 1.2 | |
| --- | |
| $id: http://devicetree.org/schemas/memory-controllers/st,stm32mp25-omm.yaml# | |
| $schema: http://devicetree.org/meta-schemas/core.yaml# | |
| title: STM32 Octo Memory Manager (OMM) | |
| maintainers: | |
| - Patrice Chotard <patrice.chotard@foss.st.com> | |
| description: | | |
| The STM32 Octo Memory Manager is a low-level interface that enables an | |
| efficient OCTOSPI pin assignment with a full I/O matrix (before alternate | |
| function map) and multiplex of single/dual/quad/octal SPI interfaces over | |
| the same bus. It Supports up to: | |
| - Two single/dual/quad/octal SPI interfaces | |
| - Two ports for pin assignment | |
| properties: | |
| compatible: | |
| const: st,stm32mp25-omm | |
| "#address-cells": | |
| const: 2 | |
| "#size-cells": | |
| const: 1 | |
| ranges: | |
| description: | | |
| Reflects the memory layout per OSPI instance. | |
| Format: | |
| <chip-select> 0 <registers base address> <size> | |
| minItems: 2 | |
| maxItems: 2 | |
| reg: | |
| items: | |
| - description: OMM registers | |
| - description: OMM memory map area | |
| reg-names: | |
| items: | |
| - const: regs | |
| - const: memory_map | |
| memory-region: | |
| description: | |
| Memory region shared between the 2 OCTOSPI instance. | |
| One or two phandle to a node describing a memory mapped region | |
| depending of child number. | |
| minItems: 1 | |
| maxItems: 2 | |
| memory-region-names: | |
| description: | |
| Identify to which OSPI instance the memory region belongs to. | |
| items: | |
| enum: [ospi1, ospi2] | |
| minItems: 1 | |
| maxItems: 2 | |
| clocks: | |
| maxItems: 3 | |
| clock-names: | |
| items: | |
| - const: omm | |
| - const: ospi1 | |
| - const: ospi2 | |
| resets: | |
| maxItems: 3 | |
| reset-names: | |
| items: | |
| - const: omm | |
| - const: ospi1 | |
| - const: ospi2 | |
| access-controllers: | |
| maxItems: 1 | |
| power-domains: | |
| maxItems: 1 | |
| st,syscfg-amcr: | |
| $ref: /schemas/types.yaml#/definitions/phandle-array | |
| description: | | |
| The Address Mapping Control Register (AMCR) is used to split the 256MB | |
| memory map area shared between the 2 OSPI instance. The Octo Memory | |
| Manager sets the AMCR depending of the memory-region configuration. | |
| The memory split bitmask description is: | |
| - 000: OCTOSPI1 (256 Mbytes), OCTOSPI2 unmapped | |
| - 001: OCTOSPI1 (192 Mbytes), OCTOSPI2 (64 Mbytes) | |
| - 010: OCTOSPI1 (128 Mbytes), OCTOSPI2 (128 Mbytes) | |
| - 011: OCTOSPI1 (64 Mbytes), OCTOSPI2 (192 Mbytes) | |
| - 1xx: OCTOSPI1 unmapped, OCTOSPI2 (256 Mbytes) | |
| items: | |
| - items: | |
| - description: phandle to syscfg | |
| - description: register offset within syscfg | |
| - description: register bitmask for memory split | |
| st,omm-req2ack-ns: | |
| description: | |
| In multiplexed mode (MUXEN = 1), this field defines the time in | |
| nanoseconds between two transactions. | |
| default: 0 | |
| st,omm-cssel-ovr: | |
| $ref: /schemas/types.yaml#/definitions/uint32 | |
| description: | | |
| Configure the chip select selector override for the 2 OCTOSPIs. | |
| - 0: OCTOSPI1 chip select send to NCS1 OCTOSPI2 chip select send to NCS1 | |
| - 1: OCTOSPI1 chip select send to NCS2 OCTOSPI2 chip select send to NCS1 | |
| - 2: OCTOSPI1 chip select send to NCS1 OCTOSPI2 chip select send to NCS2 | |
| - 3: OCTOSPI1 chip select send to NCS2 OCTOSPI2 chip select send to NCS2 | |
| minimum: 0 | |
| maximum: 3 | |
| default: 0 | |
| st,omm-mux: | |
| $ref: /schemas/types.yaml#/definitions/uint32 | |
| description: | | |
| Configure the muxing between the 2 OCTOSPIs busses and the 2 output ports. | |
| - 0: direct mode | |
| - 1: mux OCTOSPI1 and OCTOSPI2 to port 1 | |
| - 2: swapped mode | |
| - 3: mux OCTOSPI1 and OCTOSPI2 to port 2 | |
| minimum: 0 | |
| maximum: 3 | |
| default: 0 | |
| patternProperties: | |
| ^spi@[0-9]: | |
| type: object | |
| $ref: /schemas/spi/st,stm32mp25-ospi.yaml# | |
| description: Required spi child node | |
| required: | |
| - compatible | |
| - reg | |
| - "#address-cells" | |
| - "#size-cells" | |
| - clocks | |
| - clock-names | |
| - resets | |
| - reset-names | |
| - st,syscfg-amcr | |
| - ranges | |
| additionalProperties: false | |
| examples: | |
| - | | |
| #include <dt-bindings/clock/st,stm32mp25-rcc.h> | |
| #include <dt-bindings/interrupt-controller/arm-gic.h> | |
| #include <dt-bindings/reset/st,stm32mp25-rcc.h> | |
| ommanager@40500000 { | |
| compatible = "st,stm32mp25-omm"; | |
| reg = <0x40500000 0x400>, <0x60000000 0x10000000>; | |
| reg-names = "regs", "memory_map"; | |
| ranges = <0 0 0x40430000 0x400>, | |
| <1 0 0x40440000 0x400>; | |
| memory-region = <&mm_ospi1>, <&mm_ospi2>; | |
| memory-region-names = "ospi1", "ospi2"; | |
| pinctrl-0 = <&ospi_port1_clk_pins_a | |
| &ospi_port1_io03_pins_a | |
| &ospi_port1_cs0_pins_a>; | |
| pinctrl-1 = <&ospi_port1_clk_sleep_pins_a | |
| &ospi_port1_io03_sleep_pins_a | |
| &ospi_port1_cs0_sleep_pins_a>; | |
| pinctrl-names = "default", "sleep"; | |
| clocks = <&rcc CK_BUS_OSPIIOM>, | |
| <&scmi_clk CK_SCMI_OSPI1>, | |
| <&scmi_clk CK_SCMI_OSPI2>; | |
| clock-names = "omm", "ospi1", "ospi2"; | |
| resets = <&rcc OSPIIOM_R>, | |
| <&scmi_reset RST_SCMI_OSPI1>, | |
| <&scmi_reset RST_SCMI_OSPI2>; | |
| reset-names = "omm", "ospi1", "ospi2"; | |
| access-controllers = <&rifsc 111>; | |
| power-domains = <&CLUSTER_PD>; | |
| #address-cells = <2>; | |
| #size-cells = <1>; | |
| st,syscfg-amcr = <&syscfg 0x2c00 0x7>; | |
| st,omm-req2ack-ns = <0>; | |
| st,omm-mux = <0>; | |
| st,omm-cssel-ovr = <0>; | |
| spi@0 { | |
| compatible = "st,stm32mp25-ospi"; | |
| reg = <0 0 0x400>; | |
| memory-region = <&mm_ospi1>; | |
| interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>; | |
| dmas = <&hpdma 2 0x62 0x00003121 0x0>, | |
| <&hpdma 2 0x42 0x00003112 0x0>; | |
| dma-names = "tx", "rx"; | |
| clocks = <&scmi_clk CK_SCMI_OSPI1>; | |
| resets = <&scmi_reset RST_SCMI_OSPI1>, <&scmi_reset RST_SCMI_OSPI1DLL>; | |
| access-controllers = <&rifsc 74>; | |
| power-domains = <&CLUSTER_PD>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| st,syscfg-dlyb = <&syscfg 0x1000>; | |
| }; | |
| spi@1 { | |
| compatible = "st,stm32mp25-ospi"; | |
| reg = <1 0 0x400>; | |
| memory-region = <&mm_ospi1>; | |
| interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; | |
| dmas = <&hpdma 3 0x62 0x00003121 0x0>, | |
| <&hpdma 3 0x42 0x00003112 0x0>; | |
| dma-names = "tx", "rx"; | |
| clocks = <&scmi_clk CK_KER_OSPI2>; | |
| resets = <&scmi_reset RST_SCMI_OSPI2>, <&scmi_reset RST_SCMI_OSPI1DLL>; | |
| access-controllers = <&rifsc 75>; | |
| power-domains = <&CLUSTER_PD>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| st,syscfg-dlyb = <&syscfg 0x1000>; | |
| }; | |
| }; |