|  | /* | 
|  | * Driver for the Solos PCI ADSL2+ card, designed to support Linux by | 
|  | *  Traverse Technologies -- http://www.traverse.com.au/ | 
|  | *  Xrio Limited          -- http://www.xrio.com/ | 
|  | * | 
|  | * | 
|  | * Copyright © 2008 Traverse Technologies | 
|  | * Copyright © 2008 Intel Corporation | 
|  | * | 
|  | * Authors: Nathan Williams <nathan@traverse.com.au> | 
|  | *          David Woodhouse <dwmw2@infradead.org> | 
|  | *          Treker Chen <treker@xrio.com> | 
|  | * | 
|  | * This program is free software; you can redistribute it and/or | 
|  | * modify it under the terms of the GNU General Public License | 
|  | * version 2, as published by the Free Software Foundation. | 
|  | * | 
|  | * This program is distributed in the hope that it will be useful, | 
|  | * but WITHOUT ANY WARRANTY; without even the implied warranty of | 
|  | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the | 
|  | * GNU General Public License for more details. | 
|  | */ | 
|  |  | 
|  | #define DEBUG | 
|  | #define VERBOSE_DEBUG | 
|  |  | 
|  | #include <linux/interrupt.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/kernel.h> | 
|  | #include <linux/errno.h> | 
|  | #include <linux/ioport.h> | 
|  | #include <linux/types.h> | 
|  | #include <linux/pci.h> | 
|  | #include <linux/atm.h> | 
|  | #include <linux/atmdev.h> | 
|  | #include <linux/skbuff.h> | 
|  | #include <linux/sysfs.h> | 
|  | #include <linux/device.h> | 
|  | #include <linux/kobject.h> | 
|  | #include <linux/firmware.h> | 
|  | #include <linux/ctype.h> | 
|  | #include <linux/swab.h> | 
|  | #include <linux/slab.h> | 
|  |  | 
|  | #define VERSION "1.04" | 
|  | #define DRIVER_VERSION 0x01 | 
|  | #define PTAG "solos-pci" | 
|  |  | 
|  | #define CONFIG_RAM_SIZE	128 | 
|  | #define FLAGS_ADDR	0x7C | 
|  | #define IRQ_EN_ADDR	0x78 | 
|  | #define FPGA_VER	0x74 | 
|  | #define IRQ_CLEAR	0x70 | 
|  | #define WRITE_FLASH	0x6C | 
|  | #define PORTS		0x68 | 
|  | #define FLASH_BLOCK	0x64 | 
|  | #define FLASH_BUSY	0x60 | 
|  | #define FPGA_MODE	0x5C | 
|  | #define FLASH_MODE	0x58 | 
|  | #define GPIO_STATUS	0x54 | 
|  | #define DRIVER_VER	0x50 | 
|  | #define TX_DMA_ADDR(port)	(0x40 + (4 * (port))) | 
|  | #define RX_DMA_ADDR(port)	(0x30 + (4 * (port))) | 
|  |  | 
|  | #define DATA_RAM_SIZE	32768 | 
|  | #define BUF_SIZE	2048 | 
|  | #define OLD_BUF_SIZE	4096 /* For FPGA versions <= 2*/ | 
|  | /* Old boards use ATMEL AD45DB161D flash */ | 
|  | #define ATMEL_FPGA_PAGE	528 /* FPGA flash page size*/ | 
|  | #define ATMEL_SOLOS_PAGE	512 /* Solos flash page size*/ | 
|  | #define ATMEL_FPGA_BLOCK	(ATMEL_FPGA_PAGE * 8) /* FPGA block size*/ | 
|  | #define ATMEL_SOLOS_BLOCK	(ATMEL_SOLOS_PAGE * 8) /* Solos block size*/ | 
|  | /* Current boards use M25P/M25PE SPI flash */ | 
|  | #define SPI_FLASH_BLOCK	(256 * 64) | 
|  |  | 
|  | #define RX_BUF(card, nr) ((card->buffers) + (nr)*(card->buffer_size)*2) | 
|  | #define TX_BUF(card, nr) ((card->buffers) + (nr)*(card->buffer_size)*2 + (card->buffer_size)) | 
|  | #define FLASH_BUF ((card->buffers) + 4*(card->buffer_size)*2) | 
|  |  | 
|  | #define RX_DMA_SIZE	2048 | 
|  |  | 
|  | #define FPGA_VERSION(a,b) (((a) << 8) + (b)) | 
|  | #define LEGACY_BUFFERS	2 | 
|  | #define DMA_SUPPORTED	4 | 
|  |  | 
|  | static int reset = 0; | 
|  | static int atmdebug = 0; | 
|  | static int firmware_upgrade = 0; | 
|  | static int fpga_upgrade = 0; | 
|  | static int db_firmware_upgrade = 0; | 
|  | static int db_fpga_upgrade = 0; | 
|  |  | 
|  | struct pkt_hdr { | 
|  | __le16 size; | 
|  | __le16 vpi; | 
|  | __le16 vci; | 
|  | __le16 type; | 
|  | }; | 
|  |  | 
|  | struct solos_skb_cb { | 
|  | struct atm_vcc *vcc; | 
|  | uint32_t dma_addr; | 
|  | }; | 
|  |  | 
|  |  | 
|  | #define SKB_CB(skb)		((struct solos_skb_cb *)skb->cb) | 
|  |  | 
|  | #define PKT_DATA	0 | 
|  | #define PKT_COMMAND	1 | 
|  | #define PKT_POPEN	3 | 
|  | #define PKT_PCLOSE	4 | 
|  | #define PKT_STATUS	5 | 
|  |  | 
|  | struct solos_card { | 
|  | void __iomem *config_regs; | 
|  | void __iomem *buffers; | 
|  | int nr_ports; | 
|  | int tx_mask; | 
|  | struct pci_dev *dev; | 
|  | struct atm_dev *atmdev[4]; | 
|  | struct tasklet_struct tlet; | 
|  | spinlock_t tx_lock; | 
|  | spinlock_t tx_queue_lock; | 
|  | spinlock_t cli_queue_lock; | 
|  | spinlock_t param_queue_lock; | 
|  | struct list_head param_queue; | 
|  | struct sk_buff_head tx_queue[4]; | 
|  | struct sk_buff_head cli_queue[4]; | 
|  | struct sk_buff *tx_skb[4]; | 
|  | struct sk_buff *rx_skb[4]; | 
|  | unsigned char *dma_bounce; | 
|  | wait_queue_head_t param_wq; | 
|  | wait_queue_head_t fw_wq; | 
|  | int using_dma; | 
|  | int dma_alignment; | 
|  | int fpga_version; | 
|  | int buffer_size; | 
|  | int atmel_flash; | 
|  | }; | 
|  |  | 
|  |  | 
|  | struct solos_param { | 
|  | struct list_head list; | 
|  | pid_t pid; | 
|  | int port; | 
|  | struct sk_buff *response; | 
|  | }; | 
|  |  | 
|  | #define SOLOS_CHAN(atmdev) ((int)(unsigned long)(atmdev)->phy_data) | 
|  |  | 
|  | MODULE_AUTHOR("Traverse Technologies <support@traverse.com.au>"); | 
|  | MODULE_DESCRIPTION("Solos PCI driver"); | 
|  | MODULE_VERSION(VERSION); | 
|  | MODULE_LICENSE("GPL"); | 
|  | MODULE_FIRMWARE("solos-FPGA.bin"); | 
|  | MODULE_FIRMWARE("solos-Firmware.bin"); | 
|  | MODULE_FIRMWARE("solos-db-FPGA.bin"); | 
|  | MODULE_PARM_DESC(reset, "Reset Solos chips on startup"); | 
|  | MODULE_PARM_DESC(atmdebug, "Print ATM data"); | 
|  | MODULE_PARM_DESC(firmware_upgrade, "Initiate Solos firmware upgrade"); | 
|  | MODULE_PARM_DESC(fpga_upgrade, "Initiate FPGA upgrade"); | 
|  | MODULE_PARM_DESC(db_firmware_upgrade, "Initiate daughter board Solos firmware upgrade"); | 
|  | MODULE_PARM_DESC(db_fpga_upgrade, "Initiate daughter board FPGA upgrade"); | 
|  | module_param(reset, int, 0444); | 
|  | module_param(atmdebug, int, 0644); | 
|  | module_param(firmware_upgrade, int, 0444); | 
|  | module_param(fpga_upgrade, int, 0444); | 
|  | module_param(db_firmware_upgrade, int, 0444); | 
|  | module_param(db_fpga_upgrade, int, 0444); | 
|  |  | 
|  | static void fpga_queue(struct solos_card *card, int port, struct sk_buff *skb, | 
|  | struct atm_vcc *vcc); | 
|  | static uint32_t fpga_tx(struct solos_card *); | 
|  | static irqreturn_t solos_irq(int irq, void *dev_id); | 
|  | static struct atm_vcc* find_vcc(struct atm_dev *dev, short vpi, int vci); | 
|  | static int atm_init(struct solos_card *, struct device *); | 
|  | static void atm_remove(struct solos_card *); | 
|  | static int send_command(struct solos_card *card, int dev, const char *buf, size_t size); | 
|  | static void solos_bh(unsigned long); | 
|  | static int print_buffer(struct sk_buff *buf); | 
|  |  | 
|  | static inline void solos_pop(struct atm_vcc *vcc, struct sk_buff *skb) | 
|  | { | 
|  | if (vcc->pop) | 
|  | vcc->pop(vcc, skb); | 
|  | else | 
|  | dev_kfree_skb_any(skb); | 
|  | } | 
|  |  | 
|  | static ssize_t solos_param_show(struct device *dev, struct device_attribute *attr, | 
|  | char *buf) | 
|  | { | 
|  | struct atm_dev *atmdev = container_of(dev, struct atm_dev, class_dev); | 
|  | struct solos_card *card = atmdev->dev_data; | 
|  | struct solos_param prm; | 
|  | struct sk_buff *skb; | 
|  | struct pkt_hdr *header; | 
|  | int buflen; | 
|  |  | 
|  | buflen = strlen(attr->attr.name) + 10; | 
|  |  | 
|  | skb = alloc_skb(sizeof(*header) + buflen, GFP_KERNEL); | 
|  | if (!skb) { | 
|  | dev_warn(&card->dev->dev, "Failed to allocate sk_buff in solos_param_show()\n"); | 
|  | return -ENOMEM; | 
|  | } | 
|  |  | 
|  | header = (void *)skb_put(skb, sizeof(*header)); | 
|  |  | 
|  | buflen = snprintf((void *)&header[1], buflen - 1, | 
|  | "L%05d\n%s\n", current->pid, attr->attr.name); | 
|  | skb_put(skb, buflen); | 
|  |  | 
|  | header->size = cpu_to_le16(buflen); | 
|  | header->vpi = cpu_to_le16(0); | 
|  | header->vci = cpu_to_le16(0); | 
|  | header->type = cpu_to_le16(PKT_COMMAND); | 
|  |  | 
|  | prm.pid = current->pid; | 
|  | prm.response = NULL; | 
|  | prm.port = SOLOS_CHAN(atmdev); | 
|  |  | 
|  | spin_lock_irq(&card->param_queue_lock); | 
|  | list_add(&prm.list, &card->param_queue); | 
|  | spin_unlock_irq(&card->param_queue_lock); | 
|  |  | 
|  | fpga_queue(card, prm.port, skb, NULL); | 
|  |  | 
|  | wait_event_timeout(card->param_wq, prm.response, 5 * HZ); | 
|  |  | 
|  | spin_lock_irq(&card->param_queue_lock); | 
|  | list_del(&prm.list); | 
|  | spin_unlock_irq(&card->param_queue_lock); | 
|  |  | 
|  | if (!prm.response) | 
|  | return -EIO; | 
|  |  | 
|  | buflen = prm.response->len; | 
|  | memcpy(buf, prm.response->data, buflen); | 
|  | kfree_skb(prm.response); | 
|  |  | 
|  | return buflen; | 
|  | } | 
|  |  | 
|  | static ssize_t solos_param_store(struct device *dev, struct device_attribute *attr, | 
|  | const char *buf, size_t count) | 
|  | { | 
|  | struct atm_dev *atmdev = container_of(dev, struct atm_dev, class_dev); | 
|  | struct solos_card *card = atmdev->dev_data; | 
|  | struct solos_param prm; | 
|  | struct sk_buff *skb; | 
|  | struct pkt_hdr *header; | 
|  | int buflen; | 
|  | ssize_t ret; | 
|  |  | 
|  | buflen = strlen(attr->attr.name) + 11 + count; | 
|  |  | 
|  | skb = alloc_skb(sizeof(*header) + buflen, GFP_KERNEL); | 
|  | if (!skb) { | 
|  | dev_warn(&card->dev->dev, "Failed to allocate sk_buff in solos_param_store()\n"); | 
|  | return -ENOMEM; | 
|  | } | 
|  |  | 
|  | header = (void *)skb_put(skb, sizeof(*header)); | 
|  |  | 
|  | buflen = snprintf((void *)&header[1], buflen - 1, | 
|  | "L%05d\n%s\n%s\n", current->pid, attr->attr.name, buf); | 
|  |  | 
|  | skb_put(skb, buflen); | 
|  | header->size = cpu_to_le16(buflen); | 
|  | header->vpi = cpu_to_le16(0); | 
|  | header->vci = cpu_to_le16(0); | 
|  | header->type = cpu_to_le16(PKT_COMMAND); | 
|  |  | 
|  | prm.pid = current->pid; | 
|  | prm.response = NULL; | 
|  | prm.port = SOLOS_CHAN(atmdev); | 
|  |  | 
|  | spin_lock_irq(&card->param_queue_lock); | 
|  | list_add(&prm.list, &card->param_queue); | 
|  | spin_unlock_irq(&card->param_queue_lock); | 
|  |  | 
|  | fpga_queue(card, prm.port, skb, NULL); | 
|  |  | 
|  | wait_event_timeout(card->param_wq, prm.response, 5 * HZ); | 
|  |  | 
|  | spin_lock_irq(&card->param_queue_lock); | 
|  | list_del(&prm.list); | 
|  | spin_unlock_irq(&card->param_queue_lock); | 
|  |  | 
|  | skb = prm.response; | 
|  |  | 
|  | if (!skb) | 
|  | return -EIO; | 
|  |  | 
|  | buflen = skb->len; | 
|  |  | 
|  | /* Sometimes it has a newline, sometimes it doesn't. */ | 
|  | if (skb->data[buflen - 1] == '\n') | 
|  | buflen--; | 
|  |  | 
|  | if (buflen == 2 && !strncmp(skb->data, "OK", 2)) | 
|  | ret = count; | 
|  | else if (buflen == 5 && !strncmp(skb->data, "ERROR", 5)) | 
|  | ret = -EIO; | 
|  | else { | 
|  | /* We know we have enough space allocated for this; we allocated | 
|  | it ourselves */ | 
|  | skb->data[buflen] = 0; | 
|  |  | 
|  | dev_warn(&card->dev->dev, "Unexpected parameter response: '%s'\n", | 
|  | skb->data); | 
|  | ret = -EIO; | 
|  | } | 
|  | kfree_skb(skb); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static char *next_string(struct sk_buff *skb) | 
|  | { | 
|  | int i = 0; | 
|  | char *this = skb->data; | 
|  |  | 
|  | for (i = 0; i < skb->len; i++) { | 
|  | if (this[i] == '\n') { | 
|  | this[i] = 0; | 
|  | skb_pull(skb, i + 1); | 
|  | return this; | 
|  | } | 
|  | if (!isprint(this[i])) | 
|  | return NULL; | 
|  | } | 
|  | return NULL; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Status packet has fields separated by \n, starting with a version number | 
|  | * for the information therein. Fields are.... | 
|  | * | 
|  | *     packet version | 
|  | *     RxBitRate	(version >= 1) | 
|  | *     TxBitRate	(version >= 1) | 
|  | *     State		(version >= 1) | 
|  | *     LocalSNRMargin	(version >= 1) | 
|  | *     LocalLineAttn	(version >= 1) | 
|  | */ | 
|  | static int process_status(struct solos_card *card, int port, struct sk_buff *skb) | 
|  | { | 
|  | char *str, *end, *state_str, *snr, *attn; | 
|  | int ver, rate_up, rate_down; | 
|  |  | 
|  | if (!card->atmdev[port]) | 
|  | return -ENODEV; | 
|  |  | 
|  | str = next_string(skb); | 
|  | if (!str) | 
|  | return -EIO; | 
|  |  | 
|  | ver = simple_strtol(str, NULL, 10); | 
|  | if (ver < 1) { | 
|  | dev_warn(&card->dev->dev, "Unexpected status interrupt version %d\n", | 
|  | ver); | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | str = next_string(skb); | 
|  | if (!str) | 
|  | return -EIO; | 
|  | if (!strcmp(str, "ERROR")) { | 
|  | dev_dbg(&card->dev->dev, "Status packet indicated Solos error on port %d (starting up?)\n", | 
|  | port); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | rate_down = simple_strtol(str, &end, 10); | 
|  | if (*end) | 
|  | return -EIO; | 
|  |  | 
|  | str = next_string(skb); | 
|  | if (!str) | 
|  | return -EIO; | 
|  | rate_up = simple_strtol(str, &end, 10); | 
|  | if (*end) | 
|  | return -EIO; | 
|  |  | 
|  | state_str = next_string(skb); | 
|  | if (!state_str) | 
|  | return -EIO; | 
|  |  | 
|  | /* Anything but 'Showtime' is down */ | 
|  | if (strcmp(state_str, "Showtime")) { | 
|  | atm_dev_signal_change(card->atmdev[port], ATM_PHY_SIG_LOST); | 
|  | dev_info(&card->dev->dev, "Port %d: %s\n", port, state_str); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | snr = next_string(skb); | 
|  | if (!snr) | 
|  | return -EIO; | 
|  | attn = next_string(skb); | 
|  | if (!attn) | 
|  | return -EIO; | 
|  |  | 
|  | dev_info(&card->dev->dev, "Port %d: %s @%d/%d kb/s%s%s%s%s\n", | 
|  | port, state_str, rate_down/1000, rate_up/1000, | 
|  | snr[0]?", SNR ":"", snr, attn[0]?", Attn ":"", attn); | 
|  |  | 
|  | card->atmdev[port]->link_rate = rate_down / 424; | 
|  | atm_dev_signal_change(card->atmdev[port], ATM_PHY_SIG_FOUND); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int process_command(struct solos_card *card, int port, struct sk_buff *skb) | 
|  | { | 
|  | struct solos_param *prm; | 
|  | unsigned long flags; | 
|  | int cmdpid; | 
|  | int found = 0; | 
|  |  | 
|  | if (skb->len < 7) | 
|  | return 0; | 
|  |  | 
|  | if (skb->data[0] != 'L'    || !isdigit(skb->data[1]) || | 
|  | !isdigit(skb->data[2]) || !isdigit(skb->data[3]) || | 
|  | !isdigit(skb->data[4]) || !isdigit(skb->data[5]) || | 
|  | skb->data[6] != '\n') | 
|  | return 0; | 
|  |  | 
|  | cmdpid = simple_strtol(&skb->data[1], NULL, 10); | 
|  |  | 
|  | spin_lock_irqsave(&card->param_queue_lock, flags); | 
|  | list_for_each_entry(prm, &card->param_queue, list) { | 
|  | if (prm->port == port && prm->pid == cmdpid) { | 
|  | prm->response = skb; | 
|  | skb_pull(skb, 7); | 
|  | wake_up(&card->param_wq); | 
|  | found = 1; | 
|  | break; | 
|  | } | 
|  | } | 
|  | spin_unlock_irqrestore(&card->param_queue_lock, flags); | 
|  | return found; | 
|  | } | 
|  |  | 
|  | static ssize_t console_show(struct device *dev, struct device_attribute *attr, | 
|  | char *buf) | 
|  | { | 
|  | struct atm_dev *atmdev = container_of(dev, struct atm_dev, class_dev); | 
|  | struct solos_card *card = atmdev->dev_data; | 
|  | struct sk_buff *skb; | 
|  | unsigned int len; | 
|  |  | 
|  | spin_lock(&card->cli_queue_lock); | 
|  | skb = skb_dequeue(&card->cli_queue[SOLOS_CHAN(atmdev)]); | 
|  | spin_unlock(&card->cli_queue_lock); | 
|  | if(skb == NULL) | 
|  | return sprintf(buf, "No data.\n"); | 
|  |  | 
|  | len = skb->len; | 
|  | memcpy(buf, skb->data, len); | 
|  |  | 
|  | kfree_skb(skb); | 
|  | return len; | 
|  | } | 
|  |  | 
|  | static int send_command(struct solos_card *card, int dev, const char *buf, size_t size) | 
|  | { | 
|  | struct sk_buff *skb; | 
|  | struct pkt_hdr *header; | 
|  |  | 
|  | if (size > (BUF_SIZE - sizeof(*header))) { | 
|  | dev_dbg(&card->dev->dev, "Command is too big.  Dropping request\n"); | 
|  | return 0; | 
|  | } | 
|  | skb = alloc_skb(size + sizeof(*header), GFP_ATOMIC); | 
|  | if (!skb) { | 
|  | dev_warn(&card->dev->dev, "Failed to allocate sk_buff in send_command()\n"); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | header = (void *)skb_put(skb, sizeof(*header)); | 
|  |  | 
|  | header->size = cpu_to_le16(size); | 
|  | header->vpi = cpu_to_le16(0); | 
|  | header->vci = cpu_to_le16(0); | 
|  | header->type = cpu_to_le16(PKT_COMMAND); | 
|  |  | 
|  | memcpy(skb_put(skb, size), buf, size); | 
|  |  | 
|  | fpga_queue(card, dev, skb, NULL); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static ssize_t console_store(struct device *dev, struct device_attribute *attr, | 
|  | const char *buf, size_t count) | 
|  | { | 
|  | struct atm_dev *atmdev = container_of(dev, struct atm_dev, class_dev); | 
|  | struct solos_card *card = atmdev->dev_data; | 
|  | int err; | 
|  |  | 
|  | err = send_command(card, SOLOS_CHAN(atmdev), buf, count); | 
|  |  | 
|  | return err?:count; | 
|  | } | 
|  |  | 
|  | struct geos_gpio_attr { | 
|  | struct device_attribute attr; | 
|  | int offset; | 
|  | }; | 
|  |  | 
|  | #define SOLOS_GPIO_ATTR(_name, _mode, _show, _store, _offset)	\ | 
|  | struct geos_gpio_attr gpio_attr_##_name = {		\ | 
|  | .attr = __ATTR(_name, _mode, _show, _store),	\ | 
|  | .offset = _offset } | 
|  |  | 
|  | static ssize_t geos_gpio_store(struct device *dev, struct device_attribute *attr, | 
|  | const char *buf, size_t count) | 
|  | { | 
|  | struct pci_dev *pdev = container_of(dev, struct pci_dev, dev); | 
|  | struct geos_gpio_attr *gattr = container_of(attr, struct geos_gpio_attr, attr); | 
|  | struct solos_card *card = pci_get_drvdata(pdev); | 
|  | uint32_t data32; | 
|  |  | 
|  | if (count != 1 && (count != 2 || buf[1] != '\n')) | 
|  | return -EINVAL; | 
|  |  | 
|  | spin_lock_irq(&card->param_queue_lock); | 
|  | data32 = ioread32(card->config_regs + GPIO_STATUS); | 
|  | if (buf[0] == '1') { | 
|  | data32 |= 1 << gattr->offset; | 
|  | iowrite32(data32, card->config_regs + GPIO_STATUS); | 
|  | } else if (buf[0] == '0') { | 
|  | data32 &= ~(1 << gattr->offset); | 
|  | iowrite32(data32, card->config_regs + GPIO_STATUS); | 
|  | } else { | 
|  | count = -EINVAL; | 
|  | } | 
|  | spin_unlock_irq(&card->param_queue_lock); | 
|  | return count; | 
|  | } | 
|  |  | 
|  | static ssize_t geos_gpio_show(struct device *dev, struct device_attribute *attr, | 
|  | char *buf) | 
|  | { | 
|  | struct pci_dev *pdev = container_of(dev, struct pci_dev, dev); | 
|  | struct geos_gpio_attr *gattr = container_of(attr, struct geos_gpio_attr, attr); | 
|  | struct solos_card *card = pci_get_drvdata(pdev); | 
|  | uint32_t data32; | 
|  |  | 
|  | data32 = ioread32(card->config_regs + GPIO_STATUS); | 
|  | data32 = (data32 >> gattr->offset) & 1; | 
|  |  | 
|  | return sprintf(buf, "%d\n", data32); | 
|  | } | 
|  |  | 
|  | static ssize_t hardware_show(struct device *dev, struct device_attribute *attr, | 
|  | char *buf) | 
|  | { | 
|  | struct pci_dev *pdev = container_of(dev, struct pci_dev, dev); | 
|  | struct geos_gpio_attr *gattr = container_of(attr, struct geos_gpio_attr, attr); | 
|  | struct solos_card *card = pci_get_drvdata(pdev); | 
|  | uint32_t data32; | 
|  |  | 
|  | data32 = ioread32(card->config_regs + GPIO_STATUS); | 
|  | switch (gattr->offset) { | 
|  | case 0: | 
|  | /* HardwareVersion */ | 
|  | data32 = data32 & 0x1F; | 
|  | break; | 
|  | case 1: | 
|  | /* HardwareVariant */ | 
|  | data32 = (data32 >> 5) & 0x0F; | 
|  | break; | 
|  | } | 
|  | return sprintf(buf, "%d\n", data32); | 
|  | } | 
|  |  | 
|  | static DEVICE_ATTR(console, 0644, console_show, console_store); | 
|  |  | 
|  |  | 
|  | #define SOLOS_ATTR_RO(x) static DEVICE_ATTR(x, 0444, solos_param_show, NULL); | 
|  | #define SOLOS_ATTR_RW(x) static DEVICE_ATTR(x, 0644, solos_param_show, solos_param_store); | 
|  |  | 
|  | #include "solos-attrlist.c" | 
|  |  | 
|  | static SOLOS_GPIO_ATTR(GPIO1, 0644, geos_gpio_show, geos_gpio_store, 9); | 
|  | static SOLOS_GPIO_ATTR(GPIO2, 0644, geos_gpio_show, geos_gpio_store, 10); | 
|  | static SOLOS_GPIO_ATTR(GPIO3, 0644, geos_gpio_show, geos_gpio_store, 11); | 
|  | static SOLOS_GPIO_ATTR(GPIO4, 0644, geos_gpio_show, geos_gpio_store, 12); | 
|  | static SOLOS_GPIO_ATTR(GPIO5, 0644, geos_gpio_show, geos_gpio_store, 13); | 
|  | static SOLOS_GPIO_ATTR(PushButton, 0444, geos_gpio_show, NULL, 14); | 
|  | static SOLOS_GPIO_ATTR(HardwareVersion, 0444, hardware_show, NULL, 0); | 
|  | static SOLOS_GPIO_ATTR(HardwareVariant, 0444, hardware_show, NULL, 1); | 
|  | #undef SOLOS_ATTR_RO | 
|  | #undef SOLOS_ATTR_RW | 
|  |  | 
|  | #define SOLOS_ATTR_RO(x) &dev_attr_##x.attr, | 
|  | #define SOLOS_ATTR_RW(x) &dev_attr_##x.attr, | 
|  |  | 
|  | static struct attribute *solos_attrs[] = { | 
|  | #include "solos-attrlist.c" | 
|  | NULL | 
|  | }; | 
|  |  | 
|  | static struct attribute_group solos_attr_group = { | 
|  | .attrs = solos_attrs, | 
|  | .name = "parameters", | 
|  | }; | 
|  |  | 
|  | static struct attribute *gpio_attrs[] = { | 
|  | &gpio_attr_GPIO1.attr.attr, | 
|  | &gpio_attr_GPIO2.attr.attr, | 
|  | &gpio_attr_GPIO3.attr.attr, | 
|  | &gpio_attr_GPIO4.attr.attr, | 
|  | &gpio_attr_GPIO5.attr.attr, | 
|  | &gpio_attr_PushButton.attr.attr, | 
|  | &gpio_attr_HardwareVersion.attr.attr, | 
|  | &gpio_attr_HardwareVariant.attr.attr, | 
|  | NULL | 
|  | }; | 
|  |  | 
|  | static struct attribute_group gpio_attr_group = { | 
|  | .attrs = gpio_attrs, | 
|  | .name = "gpio", | 
|  | }; | 
|  |  | 
|  | static int flash_upgrade(struct solos_card *card, int chip) | 
|  | { | 
|  | const struct firmware *fw; | 
|  | const char *fw_name; | 
|  | int blocksize = 0; | 
|  | int numblocks = 0; | 
|  | int offset; | 
|  |  | 
|  | switch (chip) { | 
|  | case 0: | 
|  | fw_name = "solos-FPGA.bin"; | 
|  | if (card->atmel_flash) | 
|  | blocksize = ATMEL_FPGA_BLOCK; | 
|  | else | 
|  | blocksize = SPI_FLASH_BLOCK; | 
|  | break; | 
|  | case 1: | 
|  | fw_name = "solos-Firmware.bin"; | 
|  | if (card->atmel_flash) | 
|  | blocksize = ATMEL_SOLOS_BLOCK; | 
|  | else | 
|  | blocksize = SPI_FLASH_BLOCK; | 
|  | break; | 
|  | case 2: | 
|  | if (card->fpga_version > LEGACY_BUFFERS){ | 
|  | fw_name = "solos-db-FPGA.bin"; | 
|  | if (card->atmel_flash) | 
|  | blocksize = ATMEL_FPGA_BLOCK; | 
|  | else | 
|  | blocksize = SPI_FLASH_BLOCK; | 
|  | } else { | 
|  | dev_info(&card->dev->dev, "FPGA version doesn't support" | 
|  | " daughter board upgrades\n"); | 
|  | return -EPERM; | 
|  | } | 
|  | break; | 
|  | case 3: | 
|  | if (card->fpga_version > LEGACY_BUFFERS){ | 
|  | fw_name = "solos-Firmware.bin"; | 
|  | if (card->atmel_flash) | 
|  | blocksize = ATMEL_SOLOS_BLOCK; | 
|  | else | 
|  | blocksize = SPI_FLASH_BLOCK; | 
|  | } else { | 
|  | dev_info(&card->dev->dev, "FPGA version doesn't support" | 
|  | " daughter board upgrades\n"); | 
|  | return -EPERM; | 
|  | } | 
|  | break; | 
|  | default: | 
|  | return -ENODEV; | 
|  | } | 
|  |  | 
|  | if (request_firmware(&fw, fw_name, &card->dev->dev)) | 
|  | return -ENOENT; | 
|  |  | 
|  | dev_info(&card->dev->dev, "Flash upgrade starting\n"); | 
|  |  | 
|  | /* New FPGAs require driver version before permitting flash upgrades */ | 
|  | iowrite32(DRIVER_VERSION, card->config_regs + DRIVER_VER); | 
|  |  | 
|  | numblocks = fw->size / blocksize; | 
|  | dev_info(&card->dev->dev, "Firmware size: %zd\n", fw->size); | 
|  | dev_info(&card->dev->dev, "Number of blocks: %d\n", numblocks); | 
|  |  | 
|  | dev_info(&card->dev->dev, "Changing FPGA to Update mode\n"); | 
|  | iowrite32(1, card->config_regs + FPGA_MODE); | 
|  | (void) ioread32(card->config_regs + FPGA_MODE); | 
|  |  | 
|  | /* Set mode to Chip Erase */ | 
|  | if(chip == 0 || chip == 2) | 
|  | dev_info(&card->dev->dev, "Set FPGA Flash mode to FPGA Chip Erase\n"); | 
|  | if(chip == 1 || chip == 3) | 
|  | dev_info(&card->dev->dev, "Set FPGA Flash mode to Solos Chip Erase\n"); | 
|  | iowrite32((chip * 2), card->config_regs + FLASH_MODE); | 
|  |  | 
|  |  | 
|  | iowrite32(1, card->config_regs + WRITE_FLASH); | 
|  | wait_event(card->fw_wq, !ioread32(card->config_regs + FLASH_BUSY)); | 
|  |  | 
|  | for (offset = 0; offset < fw->size; offset += blocksize) { | 
|  | int i; | 
|  |  | 
|  | /* Clear write flag */ | 
|  | iowrite32(0, card->config_regs + WRITE_FLASH); | 
|  |  | 
|  | /* Set mode to Block Write */ | 
|  | /* dev_info(&card->dev->dev, "Set FPGA Flash mode to Block Write\n"); */ | 
|  | iowrite32(((chip * 2) + 1), card->config_regs + FLASH_MODE); | 
|  |  | 
|  | /* Copy block to buffer, swapping each 16 bits for Atmel flash */ | 
|  | for(i = 0; i < blocksize; i += 4) { | 
|  | uint32_t word; | 
|  | if (card->atmel_flash) | 
|  | word = swahb32p((uint32_t *)(fw->data + offset + i)); | 
|  | else | 
|  | word = *(uint32_t *)(fw->data + offset + i); | 
|  | if(card->fpga_version > LEGACY_BUFFERS) | 
|  | iowrite32(word, FLASH_BUF + i); | 
|  | else | 
|  | iowrite32(word, RX_BUF(card, 3) + i); | 
|  | } | 
|  |  | 
|  | /* Specify block number and then trigger flash write */ | 
|  | iowrite32(offset / blocksize, card->config_regs + FLASH_BLOCK); | 
|  | iowrite32(1, card->config_regs + WRITE_FLASH); | 
|  | wait_event(card->fw_wq, !ioread32(card->config_regs + FLASH_BUSY)); | 
|  | } | 
|  |  | 
|  | release_firmware(fw); | 
|  | iowrite32(0, card->config_regs + WRITE_FLASH); | 
|  | iowrite32(0, card->config_regs + FPGA_MODE); | 
|  | iowrite32(0, card->config_regs + FLASH_MODE); | 
|  | dev_info(&card->dev->dev, "Returning FPGA to Data mode\n"); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static irqreturn_t solos_irq(int irq, void *dev_id) | 
|  | { | 
|  | struct solos_card *card = dev_id; | 
|  | int handled = 1; | 
|  |  | 
|  | iowrite32(0, card->config_regs + IRQ_CLEAR); | 
|  |  | 
|  | /* If we're up and running, just kick the tasklet to process TX/RX */ | 
|  | if (card->atmdev[0]) | 
|  | tasklet_schedule(&card->tlet); | 
|  | else | 
|  | wake_up(&card->fw_wq); | 
|  |  | 
|  | return IRQ_RETVAL(handled); | 
|  | } | 
|  |  | 
|  | void solos_bh(unsigned long card_arg) | 
|  | { | 
|  | struct solos_card *card = (void *)card_arg; | 
|  | uint32_t card_flags; | 
|  | uint32_t rx_done = 0; | 
|  | int port; | 
|  |  | 
|  | /* | 
|  | * Since fpga_tx() is going to need to read the flags under its lock, | 
|  | * it can return them to us so that we don't have to hit PCI MMIO | 
|  | * again for the same information | 
|  | */ | 
|  | card_flags = fpga_tx(card); | 
|  |  | 
|  | for (port = 0; port < card->nr_ports; port++) { | 
|  | if (card_flags & (0x10 << port)) { | 
|  | struct pkt_hdr _hdr, *header; | 
|  | struct sk_buff *skb; | 
|  | struct atm_vcc *vcc; | 
|  | int size; | 
|  |  | 
|  | if (card->using_dma) { | 
|  | skb = card->rx_skb[port]; | 
|  | card->rx_skb[port] = NULL; | 
|  |  | 
|  | pci_unmap_single(card->dev, SKB_CB(skb)->dma_addr, | 
|  | RX_DMA_SIZE, PCI_DMA_FROMDEVICE); | 
|  |  | 
|  | header = (void *)skb->data; | 
|  | size = le16_to_cpu(header->size); | 
|  | skb_put(skb, size + sizeof(*header)); | 
|  | skb_pull(skb, sizeof(*header)); | 
|  | } else { | 
|  | header = &_hdr; | 
|  |  | 
|  | rx_done |= 0x10 << port; | 
|  |  | 
|  | memcpy_fromio(header, RX_BUF(card, port), sizeof(*header)); | 
|  |  | 
|  | size = le16_to_cpu(header->size); | 
|  | if (size > (card->buffer_size - sizeof(*header))){ | 
|  | dev_warn(&card->dev->dev, "Invalid buffer size\n"); | 
|  | continue; | 
|  | } | 
|  |  | 
|  | skb = alloc_skb(size + 1, GFP_ATOMIC); | 
|  | if (!skb) { | 
|  | if (net_ratelimit()) | 
|  | dev_warn(&card->dev->dev, "Failed to allocate sk_buff for RX\n"); | 
|  | continue; | 
|  | } | 
|  |  | 
|  | memcpy_fromio(skb_put(skb, size), | 
|  | RX_BUF(card, port) + sizeof(*header), | 
|  | size); | 
|  | } | 
|  | if (atmdebug) { | 
|  | dev_info(&card->dev->dev, "Received: port %d\n", port); | 
|  | dev_info(&card->dev->dev, "size: %d VPI: %d VCI: %d\n", | 
|  | size, le16_to_cpu(header->vpi), | 
|  | le16_to_cpu(header->vci)); | 
|  | print_buffer(skb); | 
|  | } | 
|  |  | 
|  | switch (le16_to_cpu(header->type)) { | 
|  | case PKT_DATA: | 
|  | vcc = find_vcc(card->atmdev[port], le16_to_cpu(header->vpi), | 
|  | le16_to_cpu(header->vci)); | 
|  | if (!vcc) { | 
|  | if (net_ratelimit()) | 
|  | dev_warn(&card->dev->dev, "Received packet for unknown VPI.VCI %d.%d on port %d\n", | 
|  | le16_to_cpu(header->vpi), le16_to_cpu(header->vci), | 
|  | port); | 
|  | dev_kfree_skb_any(skb); | 
|  | break; | 
|  | } | 
|  | atm_charge(vcc, skb->truesize); | 
|  | vcc->push(vcc, skb); | 
|  | atomic_inc(&vcc->stats->rx); | 
|  | break; | 
|  |  | 
|  | case PKT_STATUS: | 
|  | if (process_status(card, port, skb) && | 
|  | net_ratelimit()) { | 
|  | dev_warn(&card->dev->dev, "Bad status packet of %d bytes on port %d:\n", skb->len, port); | 
|  | print_buffer(skb); | 
|  | } | 
|  | dev_kfree_skb_any(skb); | 
|  | break; | 
|  |  | 
|  | case PKT_COMMAND: | 
|  | default: /* FIXME: Not really, surely? */ | 
|  | if (process_command(card, port, skb)) | 
|  | break; | 
|  | spin_lock(&card->cli_queue_lock); | 
|  | if (skb_queue_len(&card->cli_queue[port]) > 10) { | 
|  | if (net_ratelimit()) | 
|  | dev_warn(&card->dev->dev, "Dropping console response on port %d\n", | 
|  | port); | 
|  | dev_kfree_skb_any(skb); | 
|  | } else | 
|  | skb_queue_tail(&card->cli_queue[port], skb); | 
|  | spin_unlock(&card->cli_queue_lock); | 
|  | break; | 
|  | } | 
|  | } | 
|  | /* Allocate RX skbs for any ports which need them */ | 
|  | if (card->using_dma && card->atmdev[port] && | 
|  | !card->rx_skb[port]) { | 
|  | struct sk_buff *skb = alloc_skb(RX_DMA_SIZE, GFP_ATOMIC); | 
|  | if (skb) { | 
|  | SKB_CB(skb)->dma_addr = | 
|  | pci_map_single(card->dev, skb->data, | 
|  | RX_DMA_SIZE, PCI_DMA_FROMDEVICE); | 
|  | iowrite32(SKB_CB(skb)->dma_addr, | 
|  | card->config_regs + RX_DMA_ADDR(port)); | 
|  | card->rx_skb[port] = skb; | 
|  | } else { | 
|  | if (net_ratelimit()) | 
|  | dev_warn(&card->dev->dev, "Failed to allocate RX skb"); | 
|  |  | 
|  | /* We'll have to try again later */ | 
|  | tasklet_schedule(&card->tlet); | 
|  | } | 
|  | } | 
|  | } | 
|  | if (rx_done) | 
|  | iowrite32(rx_done, card->config_regs + FLAGS_ADDR); | 
|  |  | 
|  | return; | 
|  | } | 
|  |  | 
|  | static struct atm_vcc *find_vcc(struct atm_dev *dev, short vpi, int vci) | 
|  | { | 
|  | struct hlist_head *head; | 
|  | struct atm_vcc *vcc = NULL; | 
|  | struct sock *s; | 
|  |  | 
|  | read_lock(&vcc_sklist_lock); | 
|  | head = &vcc_hash[vci & (VCC_HTABLE_SIZE -1)]; | 
|  | sk_for_each(s, head) { | 
|  | vcc = atm_sk(s); | 
|  | if (vcc->dev == dev && vcc->vci == vci && | 
|  | vcc->vpi == vpi && vcc->qos.rxtp.traffic_class != ATM_NONE && | 
|  | test_bit(ATM_VF_READY, &vcc->flags)) | 
|  | goto out; | 
|  | } | 
|  | vcc = NULL; | 
|  | out: | 
|  | read_unlock(&vcc_sklist_lock); | 
|  | return vcc; | 
|  | } | 
|  |  | 
|  | static int popen(struct atm_vcc *vcc) | 
|  | { | 
|  | struct solos_card *card = vcc->dev->dev_data; | 
|  | struct sk_buff *skb; | 
|  | struct pkt_hdr *header; | 
|  |  | 
|  | if (vcc->qos.aal != ATM_AAL5) { | 
|  | dev_warn(&card->dev->dev, "Unsupported ATM type %d\n", | 
|  | vcc->qos.aal); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | skb = alloc_skb(sizeof(*header), GFP_KERNEL); | 
|  | if (!skb) { | 
|  | if (net_ratelimit()) | 
|  | dev_warn(&card->dev->dev, "Failed to allocate sk_buff in popen()\n"); | 
|  | return -ENOMEM; | 
|  | } | 
|  | header = (void *)skb_put(skb, sizeof(*header)); | 
|  |  | 
|  | header->size = cpu_to_le16(0); | 
|  | header->vpi = cpu_to_le16(vcc->vpi); | 
|  | header->vci = cpu_to_le16(vcc->vci); | 
|  | header->type = cpu_to_le16(PKT_POPEN); | 
|  |  | 
|  | fpga_queue(card, SOLOS_CHAN(vcc->dev), skb, NULL); | 
|  |  | 
|  | set_bit(ATM_VF_ADDR, &vcc->flags); | 
|  | set_bit(ATM_VF_READY, &vcc->flags); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void pclose(struct atm_vcc *vcc) | 
|  | { | 
|  | struct solos_card *card = vcc->dev->dev_data; | 
|  | unsigned char port = SOLOS_CHAN(vcc->dev); | 
|  | struct sk_buff *skb, *tmpskb; | 
|  | struct pkt_hdr *header; | 
|  |  | 
|  | /* Remove any yet-to-be-transmitted packets from the pending queue */ | 
|  | spin_lock(&card->tx_queue_lock); | 
|  | skb_queue_walk_safe(&card->tx_queue[port], skb, tmpskb) { | 
|  | if (SKB_CB(skb)->vcc == vcc) { | 
|  | skb_unlink(skb, &card->tx_queue[port]); | 
|  | solos_pop(vcc, skb); | 
|  | } | 
|  | } | 
|  | spin_unlock(&card->tx_queue_lock); | 
|  |  | 
|  | skb = alloc_skb(sizeof(*header), GFP_KERNEL); | 
|  | if (!skb) { | 
|  | dev_warn(&card->dev->dev, "Failed to allocate sk_buff in pclose()\n"); | 
|  | return; | 
|  | } | 
|  | header = (void *)skb_put(skb, sizeof(*header)); | 
|  |  | 
|  | header->size = cpu_to_le16(0); | 
|  | header->vpi = cpu_to_le16(vcc->vpi); | 
|  | header->vci = cpu_to_le16(vcc->vci); | 
|  | header->type = cpu_to_le16(PKT_PCLOSE); | 
|  |  | 
|  | skb_get(skb); | 
|  | fpga_queue(card, port, skb, NULL); | 
|  |  | 
|  | if (!wait_event_timeout(card->param_wq, !skb_shared(skb), 5 * HZ)) | 
|  | dev_warn(&card->dev->dev, | 
|  | "Timeout waiting for VCC close on port %d\n", port); | 
|  |  | 
|  | dev_kfree_skb(skb); | 
|  |  | 
|  | /* Hold up vcc_destroy_socket() (our caller) until solos_bh() in the | 
|  | tasklet has finished processing any incoming packets (and, more to | 
|  | the point, using the vcc pointer). */ | 
|  | tasklet_unlock_wait(&card->tlet); | 
|  |  | 
|  | clear_bit(ATM_VF_ADDR, &vcc->flags); | 
|  |  | 
|  | return; | 
|  | } | 
|  |  | 
|  | static int print_buffer(struct sk_buff *buf) | 
|  | { | 
|  | int len,i; | 
|  | char msg[500]; | 
|  | char item[10]; | 
|  |  | 
|  | len = buf->len; | 
|  | for (i = 0; i < len; i++){ | 
|  | if(i % 8 == 0) | 
|  | sprintf(msg, "%02X: ", i); | 
|  |  | 
|  | sprintf(item,"%02X ",*(buf->data + i)); | 
|  | strcat(msg, item); | 
|  | if(i % 8 == 7) { | 
|  | sprintf(item, "\n"); | 
|  | strcat(msg, item); | 
|  | printk(KERN_DEBUG "%s", msg); | 
|  | } | 
|  | } | 
|  | if (i % 8 != 0) { | 
|  | sprintf(item, "\n"); | 
|  | strcat(msg, item); | 
|  | printk(KERN_DEBUG "%s", msg); | 
|  | } | 
|  | printk(KERN_DEBUG "\n"); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void fpga_queue(struct solos_card *card, int port, struct sk_buff *skb, | 
|  | struct atm_vcc *vcc) | 
|  | { | 
|  | int old_len; | 
|  | unsigned long flags; | 
|  |  | 
|  | SKB_CB(skb)->vcc = vcc; | 
|  |  | 
|  | spin_lock_irqsave(&card->tx_queue_lock, flags); | 
|  | old_len = skb_queue_len(&card->tx_queue[port]); | 
|  | skb_queue_tail(&card->tx_queue[port], skb); | 
|  | if (!old_len) | 
|  | card->tx_mask |= (1 << port); | 
|  | spin_unlock_irqrestore(&card->tx_queue_lock, flags); | 
|  |  | 
|  | /* Theoretically we could just schedule the tasklet here, but | 
|  | that introduces latency we don't want -- it's noticeable */ | 
|  | if (!old_len) | 
|  | fpga_tx(card); | 
|  | } | 
|  |  | 
|  | static uint32_t fpga_tx(struct solos_card *card) | 
|  | { | 
|  | uint32_t tx_pending, card_flags; | 
|  | uint32_t tx_started = 0; | 
|  | struct sk_buff *skb; | 
|  | struct atm_vcc *vcc; | 
|  | unsigned char port; | 
|  | unsigned long flags; | 
|  |  | 
|  | spin_lock_irqsave(&card->tx_lock, flags); | 
|  |  | 
|  | card_flags = ioread32(card->config_regs + FLAGS_ADDR); | 
|  | /* | 
|  | * The queue lock is required for _writing_ to tx_mask, but we're | 
|  | * OK to read it here without locking. The only potential update | 
|  | * that we could race with is in fpga_queue() where it sets a bit | 
|  | * for a new port... but it's going to call this function again if | 
|  | * it's doing that, anyway. | 
|  | */ | 
|  | tx_pending = card->tx_mask & ~card_flags; | 
|  |  | 
|  | for (port = 0; tx_pending; tx_pending >>= 1, port++) { | 
|  | if (tx_pending & 1) { | 
|  | struct sk_buff *oldskb = card->tx_skb[port]; | 
|  | if (oldskb) { | 
|  | pci_unmap_single(card->dev, SKB_CB(oldskb)->dma_addr, | 
|  | oldskb->len, PCI_DMA_TODEVICE); | 
|  | card->tx_skb[port] = NULL; | 
|  | } | 
|  | spin_lock(&card->tx_queue_lock); | 
|  | skb = skb_dequeue(&card->tx_queue[port]); | 
|  | if (!skb) | 
|  | card->tx_mask &= ~(1 << port); | 
|  | spin_unlock(&card->tx_queue_lock); | 
|  |  | 
|  | if (skb && !card->using_dma) { | 
|  | memcpy_toio(TX_BUF(card, port), skb->data, skb->len); | 
|  | tx_started |= 1 << port; | 
|  | oldskb = skb; /* We're done with this skb already */ | 
|  | } else if (skb && card->using_dma) { | 
|  | unsigned char *data = skb->data; | 
|  | if ((unsigned long)data & card->dma_alignment) { | 
|  | data = card->dma_bounce + (BUF_SIZE * port); | 
|  | memcpy(data, skb->data, skb->len); | 
|  | } | 
|  | SKB_CB(skb)->dma_addr = pci_map_single(card->dev, data, | 
|  | skb->len, PCI_DMA_TODEVICE); | 
|  | card->tx_skb[port] = skb; | 
|  | iowrite32(SKB_CB(skb)->dma_addr, | 
|  | card->config_regs + TX_DMA_ADDR(port)); | 
|  | } | 
|  |  | 
|  | if (!oldskb) | 
|  | continue; | 
|  |  | 
|  | /* Clean up and free oldskb now it's gone */ | 
|  | if (atmdebug) { | 
|  | struct pkt_hdr *header = (void *)oldskb->data; | 
|  | int size = le16_to_cpu(header->size); | 
|  |  | 
|  | skb_pull(oldskb, sizeof(*header)); | 
|  | dev_info(&card->dev->dev, "Transmitted: port %d\n", | 
|  | port); | 
|  | dev_info(&card->dev->dev, "size: %d VPI: %d VCI: %d\n", | 
|  | size, le16_to_cpu(header->vpi), | 
|  | le16_to_cpu(header->vci)); | 
|  | print_buffer(oldskb); | 
|  | } | 
|  |  | 
|  | vcc = SKB_CB(oldskb)->vcc; | 
|  |  | 
|  | if (vcc) { | 
|  | atomic_inc(&vcc->stats->tx); | 
|  | solos_pop(vcc, oldskb); | 
|  | } else { | 
|  | dev_kfree_skb_irq(oldskb); | 
|  | wake_up(&card->param_wq); | 
|  | } | 
|  | } | 
|  | } | 
|  | /* For non-DMA TX, write the 'TX start' bit for all four ports simultaneously */ | 
|  | if (tx_started) | 
|  | iowrite32(tx_started, card->config_regs + FLAGS_ADDR); | 
|  |  | 
|  | spin_unlock_irqrestore(&card->tx_lock, flags); | 
|  | return card_flags; | 
|  | } | 
|  |  | 
|  | static int psend(struct atm_vcc *vcc, struct sk_buff *skb) | 
|  | { | 
|  | struct solos_card *card = vcc->dev->dev_data; | 
|  | struct pkt_hdr *header; | 
|  | int pktlen; | 
|  |  | 
|  | pktlen = skb->len; | 
|  | if (pktlen > (BUF_SIZE - sizeof(*header))) { | 
|  | dev_warn(&card->dev->dev, "Length of PDU is too large. Dropping PDU.\n"); | 
|  | solos_pop(vcc, skb); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | if (!skb_clone_writable(skb, sizeof(*header))) { | 
|  | int expand_by = 0; | 
|  | int ret; | 
|  |  | 
|  | if (skb_headroom(skb) < sizeof(*header)) | 
|  | expand_by = sizeof(*header) - skb_headroom(skb); | 
|  |  | 
|  | ret = pskb_expand_head(skb, expand_by, 0, GFP_ATOMIC); | 
|  | if (ret) { | 
|  | dev_warn(&card->dev->dev, "pskb_expand_head failed.\n"); | 
|  | solos_pop(vcc, skb); | 
|  | return ret; | 
|  | } | 
|  | } | 
|  |  | 
|  | header = (void *)skb_push(skb, sizeof(*header)); | 
|  |  | 
|  | /* This does _not_ include the size of the header */ | 
|  | header->size = cpu_to_le16(pktlen); | 
|  | header->vpi = cpu_to_le16(vcc->vpi); | 
|  | header->vci = cpu_to_le16(vcc->vci); | 
|  | header->type = cpu_to_le16(PKT_DATA); | 
|  |  | 
|  | fpga_queue(card, SOLOS_CHAN(vcc->dev), skb, vcc); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static struct atmdev_ops fpga_ops = { | 
|  | .open =		popen, | 
|  | .close =	pclose, | 
|  | .ioctl =	NULL, | 
|  | .getsockopt =	NULL, | 
|  | .setsockopt =	NULL, | 
|  | .send =		psend, | 
|  | .send_oam =	NULL, | 
|  | .phy_put =	NULL, | 
|  | .phy_get =	NULL, | 
|  | .change_qos =	NULL, | 
|  | .proc_read =	NULL, | 
|  | .owner =	THIS_MODULE | 
|  | }; | 
|  |  | 
|  | static int fpga_probe(struct pci_dev *dev, const struct pci_device_id *id) | 
|  | { | 
|  | int err; | 
|  | uint16_t fpga_ver; | 
|  | uint8_t major_ver, minor_ver; | 
|  | uint32_t data32; | 
|  | struct solos_card *card; | 
|  |  | 
|  | card = kzalloc(sizeof(*card), GFP_KERNEL); | 
|  | if (!card) | 
|  | return -ENOMEM; | 
|  |  | 
|  | card->dev = dev; | 
|  | init_waitqueue_head(&card->fw_wq); | 
|  | init_waitqueue_head(&card->param_wq); | 
|  |  | 
|  | err = pci_enable_device(dev); | 
|  | if (err) { | 
|  | dev_warn(&dev->dev,  "Failed to enable PCI device\n"); | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | err = pci_set_dma_mask(dev, DMA_BIT_MASK(32)); | 
|  | if (err) { | 
|  | dev_warn(&dev->dev, "Failed to set 32-bit DMA mask\n"); | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | err = pci_request_regions(dev, "solos"); | 
|  | if (err) { | 
|  | dev_warn(&dev->dev, "Failed to request regions\n"); | 
|  | goto out; | 
|  | } | 
|  |  | 
|  | card->config_regs = pci_iomap(dev, 0, CONFIG_RAM_SIZE); | 
|  | if (!card->config_regs) { | 
|  | dev_warn(&dev->dev, "Failed to ioremap config registers\n"); | 
|  | goto out_release_regions; | 
|  | } | 
|  | card->buffers = pci_iomap(dev, 1, DATA_RAM_SIZE); | 
|  | if (!card->buffers) { | 
|  | dev_warn(&dev->dev, "Failed to ioremap data buffers\n"); | 
|  | goto out_unmap_config; | 
|  | } | 
|  |  | 
|  | if (reset) { | 
|  | iowrite32(1, card->config_regs + FPGA_MODE); | 
|  | data32 = ioread32(card->config_regs + FPGA_MODE); | 
|  |  | 
|  | iowrite32(0, card->config_regs + FPGA_MODE); | 
|  | data32 = ioread32(card->config_regs + FPGA_MODE); | 
|  | } | 
|  |  | 
|  | data32 = ioread32(card->config_regs + FPGA_VER); | 
|  | fpga_ver = (data32 & 0x0000FFFF); | 
|  | major_ver = ((data32 & 0xFF000000) >> 24); | 
|  | minor_ver = ((data32 & 0x00FF0000) >> 16); | 
|  | card->fpga_version = FPGA_VERSION(major_ver,minor_ver); | 
|  | if (card->fpga_version > LEGACY_BUFFERS) | 
|  | card->buffer_size = BUF_SIZE; | 
|  | else | 
|  | card->buffer_size = OLD_BUF_SIZE; | 
|  | dev_info(&dev->dev, "Solos FPGA Version %d.%02d svn-%d\n", | 
|  | major_ver, minor_ver, fpga_ver); | 
|  |  | 
|  | if (fpga_ver < 37 && (fpga_upgrade || firmware_upgrade || | 
|  | db_fpga_upgrade || db_firmware_upgrade)) { | 
|  | dev_warn(&dev->dev, | 
|  | "FPGA too old; cannot upgrade flash. Use JTAG.\n"); | 
|  | fpga_upgrade = firmware_upgrade = 0; | 
|  | db_fpga_upgrade = db_firmware_upgrade = 0; | 
|  | } | 
|  |  | 
|  | /* Stopped using Atmel flash after 0.03-38 */ | 
|  | if (fpga_ver < 39) | 
|  | card->atmel_flash = 1; | 
|  | else | 
|  | card->atmel_flash = 0; | 
|  |  | 
|  | data32 = ioread32(card->config_regs + PORTS); | 
|  | card->nr_ports = (data32 & 0x000000FF); | 
|  |  | 
|  | if (card->fpga_version >= DMA_SUPPORTED) { | 
|  | pci_set_master(dev); | 
|  | card->using_dma = 1; | 
|  | if (1) { /* All known FPGA versions so far */ | 
|  | card->dma_alignment = 3; | 
|  | card->dma_bounce = kmalloc(card->nr_ports * BUF_SIZE, GFP_KERNEL); | 
|  | if (!card->dma_bounce) { | 
|  | dev_warn(&card->dev->dev, "Failed to allocate DMA bounce buffers\n"); | 
|  | /* Fallback to MMIO doesn't work */ | 
|  | goto out_unmap_both; | 
|  | } | 
|  | } | 
|  | } else { | 
|  | card->using_dma = 0; | 
|  | /* Set RX empty flag for all ports */ | 
|  | iowrite32(0xF0, card->config_regs + FLAGS_ADDR); | 
|  | } | 
|  |  | 
|  | pci_set_drvdata(dev, card); | 
|  |  | 
|  | tasklet_init(&card->tlet, solos_bh, (unsigned long)card); | 
|  | spin_lock_init(&card->tx_lock); | 
|  | spin_lock_init(&card->tx_queue_lock); | 
|  | spin_lock_init(&card->cli_queue_lock); | 
|  | spin_lock_init(&card->param_queue_lock); | 
|  | INIT_LIST_HEAD(&card->param_queue); | 
|  |  | 
|  | err = request_irq(dev->irq, solos_irq, IRQF_SHARED, | 
|  | "solos-pci", card); | 
|  | if (err) { | 
|  | dev_dbg(&card->dev->dev, "Failed to request interrupt IRQ: %d\n", dev->irq); | 
|  | goto out_unmap_both; | 
|  | } | 
|  |  | 
|  | iowrite32(1, card->config_regs + IRQ_EN_ADDR); | 
|  |  | 
|  | if (fpga_upgrade) | 
|  | flash_upgrade(card, 0); | 
|  |  | 
|  | if (firmware_upgrade) | 
|  | flash_upgrade(card, 1); | 
|  |  | 
|  | if (db_fpga_upgrade) | 
|  | flash_upgrade(card, 2); | 
|  |  | 
|  | if (db_firmware_upgrade) | 
|  | flash_upgrade(card, 3); | 
|  |  | 
|  | err = atm_init(card, &dev->dev); | 
|  | if (err) | 
|  | goto out_free_irq; | 
|  |  | 
|  | if (card->fpga_version >= DMA_SUPPORTED && | 
|  | sysfs_create_group(&card->dev->dev.kobj, &gpio_attr_group)) | 
|  | dev_err(&card->dev->dev, "Could not register parameter group for GPIOs\n"); | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | out_free_irq: | 
|  | iowrite32(0, card->config_regs + IRQ_EN_ADDR); | 
|  | free_irq(dev->irq, card); | 
|  | tasklet_kill(&card->tlet); | 
|  |  | 
|  | out_unmap_both: | 
|  | kfree(card->dma_bounce); | 
|  | pci_set_drvdata(dev, NULL); | 
|  | pci_iounmap(dev, card->buffers); | 
|  | out_unmap_config: | 
|  | pci_iounmap(dev, card->config_regs); | 
|  | out_release_regions: | 
|  | pci_release_regions(dev); | 
|  | out: | 
|  | kfree(card); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int atm_init(struct solos_card *card, struct device *parent) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i < card->nr_ports; i++) { | 
|  | struct sk_buff *skb; | 
|  | struct pkt_hdr *header; | 
|  |  | 
|  | skb_queue_head_init(&card->tx_queue[i]); | 
|  | skb_queue_head_init(&card->cli_queue[i]); | 
|  |  | 
|  | card->atmdev[i] = atm_dev_register("solos-pci", parent, &fpga_ops, -1, NULL); | 
|  | if (!card->atmdev[i]) { | 
|  | dev_err(&card->dev->dev, "Could not register ATM device %d\n", i); | 
|  | atm_remove(card); | 
|  | return -ENODEV; | 
|  | } | 
|  | if (device_create_file(&card->atmdev[i]->class_dev, &dev_attr_console)) | 
|  | dev_err(&card->dev->dev, "Could not register console for ATM device %d\n", i); | 
|  | if (sysfs_create_group(&card->atmdev[i]->class_dev.kobj, &solos_attr_group)) | 
|  | dev_err(&card->dev->dev, "Could not register parameter group for ATM device %d\n", i); | 
|  |  | 
|  | dev_info(&card->dev->dev, "Registered ATM device %d\n", card->atmdev[i]->number); | 
|  |  | 
|  | card->atmdev[i]->ci_range.vpi_bits = 8; | 
|  | card->atmdev[i]->ci_range.vci_bits = 16; | 
|  | card->atmdev[i]->dev_data = card; | 
|  | card->atmdev[i]->phy_data = (void *)(unsigned long)i; | 
|  | atm_dev_signal_change(card->atmdev[i], ATM_PHY_SIG_FOUND); | 
|  |  | 
|  | skb = alloc_skb(sizeof(*header), GFP_KERNEL); | 
|  | if (!skb) { | 
|  | dev_warn(&card->dev->dev, "Failed to allocate sk_buff in atm_init()\n"); | 
|  | continue; | 
|  | } | 
|  |  | 
|  | header = (void *)skb_put(skb, sizeof(*header)); | 
|  |  | 
|  | header->size = cpu_to_le16(0); | 
|  | header->vpi = cpu_to_le16(0); | 
|  | header->vci = cpu_to_le16(0); | 
|  | header->type = cpu_to_le16(PKT_STATUS); | 
|  |  | 
|  | fpga_queue(card, i, skb, NULL); | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void atm_remove(struct solos_card *card) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i < card->nr_ports; i++) { | 
|  | if (card->atmdev[i]) { | 
|  | struct sk_buff *skb; | 
|  |  | 
|  | dev_info(&card->dev->dev, "Unregistering ATM device %d\n", card->atmdev[i]->number); | 
|  |  | 
|  | sysfs_remove_group(&card->atmdev[i]->class_dev.kobj, &solos_attr_group); | 
|  | atm_dev_deregister(card->atmdev[i]); | 
|  |  | 
|  | skb = card->rx_skb[i]; | 
|  | if (skb) { | 
|  | pci_unmap_single(card->dev, SKB_CB(skb)->dma_addr, | 
|  | RX_DMA_SIZE, PCI_DMA_FROMDEVICE); | 
|  | dev_kfree_skb(skb); | 
|  | } | 
|  | skb = card->tx_skb[i]; | 
|  | if (skb) { | 
|  | pci_unmap_single(card->dev, SKB_CB(skb)->dma_addr, | 
|  | skb->len, PCI_DMA_TODEVICE); | 
|  | dev_kfree_skb(skb); | 
|  | } | 
|  | while ((skb = skb_dequeue(&card->tx_queue[i]))) | 
|  | dev_kfree_skb(skb); | 
|  |  | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static void fpga_remove(struct pci_dev *dev) | 
|  | { | 
|  | struct solos_card *card = pci_get_drvdata(dev); | 
|  |  | 
|  | /* Disable IRQs */ | 
|  | iowrite32(0, card->config_regs + IRQ_EN_ADDR); | 
|  |  | 
|  | /* Reset FPGA */ | 
|  | iowrite32(1, card->config_regs + FPGA_MODE); | 
|  | (void)ioread32(card->config_regs + FPGA_MODE); | 
|  |  | 
|  | if (card->fpga_version >= DMA_SUPPORTED) | 
|  | sysfs_remove_group(&card->dev->dev.kobj, &gpio_attr_group); | 
|  |  | 
|  | atm_remove(card); | 
|  |  | 
|  | free_irq(dev->irq, card); | 
|  | tasklet_kill(&card->tlet); | 
|  |  | 
|  | kfree(card->dma_bounce); | 
|  |  | 
|  | /* Release device from reset */ | 
|  | iowrite32(0, card->config_regs + FPGA_MODE); | 
|  | (void)ioread32(card->config_regs + FPGA_MODE); | 
|  |  | 
|  | pci_iounmap(dev, card->buffers); | 
|  | pci_iounmap(dev, card->config_regs); | 
|  |  | 
|  | pci_release_regions(dev); | 
|  | pci_disable_device(dev); | 
|  |  | 
|  | pci_set_drvdata(dev, NULL); | 
|  | kfree(card); | 
|  | } | 
|  |  | 
|  | static struct pci_device_id fpga_pci_tbl[] = { | 
|  | { 0x10ee, 0x0300, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 }, | 
|  | { 0, } | 
|  | }; | 
|  |  | 
|  | MODULE_DEVICE_TABLE(pci,fpga_pci_tbl); | 
|  |  | 
|  | static struct pci_driver fpga_driver = { | 
|  | .name =		"solos", | 
|  | .id_table =	fpga_pci_tbl, | 
|  | .probe =	fpga_probe, | 
|  | .remove =	fpga_remove, | 
|  | }; | 
|  |  | 
|  |  | 
|  | static int __init solos_pci_init(void) | 
|  | { | 
|  | BUILD_BUG_ON(sizeof(struct solos_skb_cb) > sizeof(((struct sk_buff *)0)->cb)); | 
|  |  | 
|  | printk(KERN_INFO "Solos PCI Driver Version %s\n", VERSION); | 
|  | return pci_register_driver(&fpga_driver); | 
|  | } | 
|  |  | 
|  | static void __exit solos_pci_exit(void) | 
|  | { | 
|  | pci_unregister_driver(&fpga_driver); | 
|  | printk(KERN_INFO "Solos PCI Driver %s Unloaded\n", VERSION); | 
|  | } | 
|  |  | 
|  | module_init(solos_pci_init); | 
|  | module_exit(solos_pci_exit); |