blob: 955e335e7e5698d14f4631441d4d1de3a8e3a047 [file] [log] [blame]
OMAP SSI controller bindings
OMAP3's Synchronous Serial Interface (SSI) controller implements a
legacy variant of MIPI's High Speed Synchronous Serial Interface (HSI),
while the controller found inside OMAP4 is supposed to be fully compliant
with the HSI standard.
Required properties:
- compatible: Should include "ti,omap3-ssi" or "ti,omap4-hsi"
- reg-names: Contains the values "sys" and "gdd" (in this order).
- reg: Contains a matching register specifier for each entry
in reg-names.
- interrupt-names: Contains the value "gdd_mpu".
- interrupts: Contains matching interrupt information for each entry
in interrupt-names.
- ranges: Represents the bus address mapping between the main
controller node and the child nodes below.
- clock-names: Must include the following entries:
"ssi_ssr_fck": The OMAP clock of that name
"ssi_sst_fck": The OMAP clock of that name
"ssi_ick": The OMAP clock of that name
- clocks: Contains a matching clock specifier for each entry in
clock-names.
- #address-cells: Should be set to <1>
- #size-cells: Should be set to <1>
Each port is represented as a sub-node of the ti,omap3-ssi device.
Required Port sub-node properties:
- compatible: Should be set to the following value
ti,omap3-ssi-port (applicable to OMAP34xx devices)
ti,omap4-hsi-port (applicable to OMAP44xx devices)
- reg-names: Contains the values "tx" and "rx" (in this order).
- reg: Contains a matching register specifier for each entry
in reg-names.
- interrupt-parent Should be a phandle for the interrupt controller
- interrupts: Should contain interrupt specifiers for mpu interrupts
0 and 1 (in this order).
- ti,ssi-cawake-gpio: Defines which GPIO pin is used to signify CAWAKE
events for the port. This is an optional board-specific
property. If it's missing the port will not be
enabled.
Optional properties:
- ti,hwmods: Shall contain TI interconnect module name if needed
by the SoC
Example for Nokia N900:
ssi-controller@48058000 {
compatible = "ti,omap3-ssi";
/* needed until hwmod is updated to use the compatible string */
ti,hwmods = "ssi";
reg = <0x48058000 0x1000>,
<0x48059000 0x1000>;
reg-names = "sys",
"gdd";
interrupts = <55>;
interrupt-names = "gdd_mpu";
clocks = <&ssi_ssr_fck>,
<&ssi_sst_fck>,
<&ssi_ick>;
clock-names = "ssi_ssr_fck",
"ssi_sst_fck",
"ssi_ick";
#address-cells = <1>;
#size-cells = <1>;
ranges;
ssi-port@4805a000 {
compatible = "ti,omap3-ssi-port";
reg = <0x4805a000 0x800>,
<0x4805a800 0x800>;
reg-names = "tx",
"rx";
interrupt-parent = <&intc>;
interrupts = <67>,
<68>;
ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */
}
ssi-port@4805a000 {
compatible = "ti,omap3-ssi-port";
reg = <0x4805b000 0x800>,
<0x4805b800 0x800>;
reg-names = "tx",
"rx";
interrupt-parent = <&intc>;
interrupts = <69>,
<70>;
}
}