| Documentation for /proc/sys/net/* |
| (c) 1999 Terrehon Bowden <terrehon@pacbell.net> |
| Bodo Bauer <bb@ricochet.net> |
| (c) 2000 Jorge Nerin <comandante@zaralinux.com> |
| (c) 2009 Shen Feng <shen@cn.fujitsu.com> |
| |
| For general info and legal blurb, please look in README. |
| |
| ============================================================== |
| |
| This file contains the documentation for the sysctl files in |
| /proc/sys/net |
| |
| The interface to the networking parts of the kernel is located in |
| /proc/sys/net. The following table shows all possible subdirectories. You may |
| see only some of them, depending on your kernel's configuration. |
| |
| |
| Table : Subdirectories in /proc/sys/net |
| .............................................................................. |
| Directory Content Directory Content |
| core General parameter appletalk Appletalk protocol |
| unix Unix domain sockets netrom NET/ROM |
| 802 E802 protocol ax25 AX25 |
| ethernet Ethernet protocol rose X.25 PLP layer |
| ipv4 IP version 4 x25 X.25 protocol |
| ipx IPX token-ring IBM token ring |
| bridge Bridging decnet DEC net |
| ipv6 IP version 6 tipc TIPC |
| .............................................................................. |
| |
| 1. /proc/sys/net/core - Network core options |
| ------------------------------------------------------- |
| |
| bpf_jit_enable |
| -------------- |
| |
| This enables Berkeley Packet Filter Just in Time compiler. |
| Currently supported on x86_64 architecture, bpf_jit provides a framework |
| to speed packet filtering, the one used by tcpdump/libpcap for example. |
| Values : |
| 0 - disable the JIT (default value) |
| 1 - enable the JIT |
| 2 - enable the JIT and ask the compiler to emit traces on kernel log. |
| |
| dev_weight |
| -------------- |
| |
| The maximum number of packets that kernel can handle on a NAPI interrupt, |
| it's a Per-CPU variable. |
| Default: 64 |
| |
| default_qdisc |
| -------------- |
| |
| The default queuing discipline to use for network devices. This allows |
| overriding the default queue discipline of pfifo_fast with an |
| alternative. Since the default queuing discipline is created with the |
| no additional parameters so is best suited to queuing disciplines that |
| work well without configuration like stochastic fair queue (sfq), |
| CoDel (codel) or fair queue CoDel (fq_codel). Don't use queuing disciplines |
| like Hierarchical Token Bucket or Deficit Round Robin which require setting |
| up classes and bandwidths. |
| Default: pfifo_fast |
| |
| busy_read |
| ---------------- |
| Low latency busy poll timeout for socket reads. (needs CONFIG_NET_RX_BUSY_POLL) |
| Approximate time in us to busy loop waiting for packets on the device queue. |
| This sets the default value of the SO_BUSY_POLL socket option. |
| Can be set or overridden per socket by setting socket option SO_BUSY_POLL, |
| which is the preferred method of enabling. If you need to enable the feature |
| globally via sysctl, a value of 50 is recommended. |
| Will increase power usage. |
| Default: 0 (off) |
| |
| busy_poll |
| ---------------- |
| Low latency busy poll timeout for poll and select. (needs CONFIG_NET_RX_BUSY_POLL) |
| Approximate time in us to busy loop waiting for events. |
| Recommended value depends on the number of sockets you poll on. |
| For several sockets 50, for several hundreds 100. |
| For more than that you probably want to use epoll. |
| Note that only sockets with SO_BUSY_POLL set will be busy polled, |
| so you want to either selectively set SO_BUSY_POLL on those sockets or set |
| sysctl.net.busy_read globally. |
| Will increase power usage. |
| Default: 0 (off) |
| |
| rmem_default |
| ------------ |
| |
| The default setting of the socket receive buffer in bytes. |
| |
| rmem_max |
| -------- |
| |
| The maximum receive socket buffer size in bytes. |
| |
| wmem_default |
| ------------ |
| |
| The default setting (in bytes) of the socket send buffer. |
| |
| wmem_max |
| -------- |
| |
| The maximum send socket buffer size in bytes. |
| |
| message_burst and message_cost |
| ------------------------------ |
| |
| These parameters are used to limit the warning messages written to the kernel |
| log from the networking code. They enforce a rate limit to make a |
| denial-of-service attack impossible. A higher message_cost factor, results in |
| fewer messages that will be written. Message_burst controls when messages will |
| be dropped. The default settings limit warning messages to one every five |
| seconds. |
| |
| warnings |
| -------- |
| |
| This sysctl is now unused. |
| |
| This was used to control console messages from the networking stack that |
| occur because of problems on the network like duplicate address or bad |
| checksums. |
| |
| These messages are now emitted at KERN_DEBUG and can generally be enabled |
| and controlled by the dynamic_debug facility. |
| |
| netdev_budget |
| ------------- |
| |
| Maximum number of packets taken from all interfaces in one polling cycle (NAPI |
| poll). In one polling cycle interfaces which are registered to polling are |
| probed in a round-robin manner. |
| |
| netdev_max_backlog |
| ------------------ |
| |
| Maximum number of packets, queued on the INPUT side, when the interface |
| receives packets faster than kernel can process them. |
| |
| netdev_rss_key |
| -------------- |
| |
| RSS (Receive Side Scaling) enabled drivers use a 40 bytes host key that is |
| randomly generated. |
| Some user space might need to gather its content even if drivers do not |
| provide ethtool -x support yet. |
| |
| myhost:~# cat /proc/sys/net/core/netdev_rss_key |
| 84:50:f4:00:a8:15:d1:a7:e9:7f:1d:60:35:c7:47:25:42:97:74:ca:56:bb:b6:a1:d8: ... (52 bytes total) |
| |
| File contains nul bytes if no driver ever called netdev_rss_key_fill() function. |
| Note: |
| /proc/sys/net/core/netdev_rss_key contains 52 bytes of key, |
| but most drivers only use 40 bytes of it. |
| |
| myhost:~# ethtool -x eth0 |
| RX flow hash indirection table for eth0 with 8 RX ring(s): |
| 0: 0 1 2 3 4 5 6 7 |
| RSS hash key: |
| 84:50:f4:00:a8:15:d1:a7:e9:7f:1d:60:35:c7:47:25:42:97:74:ca:56:bb:b6:a1:d8:43:e3:c9:0c:fd:17:55:c2:3a:4d:69:ed:f1:42:89 |
| |
| netdev_tstamp_prequeue |
| ---------------------- |
| |
| If set to 0, RX packet timestamps can be sampled after RPS processing, when |
| the target CPU processes packets. It might give some delay on timestamps, but |
| permit to distribute the load on several cpus. |
| |
| If set to 1 (default), timestamps are sampled as soon as possible, before |
| queueing. |
| |
| optmem_max |
| ---------- |
| |
| Maximum ancillary buffer size allowed per socket. Ancillary data is a sequence |
| of struct cmsghdr structures with appended data. |
| |
| 2. /proc/sys/net/unix - Parameters for Unix domain sockets |
| ------------------------------------------------------- |
| |
| There is only one file in this directory. |
| unix_dgram_qlen limits the max number of datagrams queued in Unix domain |
| socket's buffer. It will not take effect unless PF_UNIX flag is specified. |
| |
| |
| 3. /proc/sys/net/ipv4 - IPV4 settings |
| ------------------------------------------------------- |
| Please see: Documentation/networking/ip-sysctl.txt and ipvs-sysctl.txt for |
| descriptions of these entries. |
| |
| |
| 4. Appletalk |
| ------------------------------------------------------- |
| |
| The /proc/sys/net/appletalk directory holds the Appletalk configuration data |
| when Appletalk is loaded. The configurable parameters are: |
| |
| aarp-expiry-time |
| ---------------- |
| |
| The amount of time we keep an ARP entry before expiring it. Used to age out |
| old hosts. |
| |
| aarp-resolve-time |
| ----------------- |
| |
| The amount of time we will spend trying to resolve an Appletalk address. |
| |
| aarp-retransmit-limit |
| --------------------- |
| |
| The number of times we will retransmit a query before giving up. |
| |
| aarp-tick-time |
| -------------- |
| |
| Controls the rate at which expires are checked. |
| |
| The directory /proc/net/appletalk holds the list of active Appletalk sockets |
| on a machine. |
| |
| The fields indicate the DDP type, the local address (in network:node format) |
| the remote address, the size of the transmit pending queue, the size of the |
| received queue (bytes waiting for applications to read) the state and the uid |
| owning the socket. |
| |
| /proc/net/atalk_iface lists all the interfaces configured for appletalk.It |
| shows the name of the interface, its Appletalk address, the network range on |
| that address (or network number for phase 1 networks), and the status of the |
| interface. |
| |
| /proc/net/atalk_route lists each known network route. It lists the target |
| (network) that the route leads to, the router (may be directly connected), the |
| route flags, and the device the route is using. |
| |
| |
| 5. IPX |
| ------------------------------------------------------- |
| |
| The IPX protocol has no tunable values in proc/sys/net. |
| |
| The IPX protocol does, however, provide proc/net/ipx. This lists each IPX |
| socket giving the local and remote addresses in Novell format (that is |
| network:node:port). In accordance with the strange Novell tradition, |
| everything but the port is in hex. Not_Connected is displayed for sockets that |
| are not tied to a specific remote address. The Tx and Rx queue sizes indicate |
| the number of bytes pending for transmission and reception. The state |
| indicates the state the socket is in and the uid is the owning uid of the |
| socket. |
| |
| The /proc/net/ipx_interface file lists all IPX interfaces. For each interface |
| it gives the network number, the node number, and indicates if the network is |
| the primary network. It also indicates which device it is bound to (or |
| Internal for internal networks) and the Frame Type if appropriate. Linux |
| supports 802.3, 802.2, 802.2 SNAP and DIX (Blue Book) ethernet framing for |
| IPX. |
| |
| The /proc/net/ipx_route table holds a list of IPX routes. For each route it |
| gives the destination network, the router node (or Directly) and the network |
| address of the router (or Connected) for internal networks. |
| |
| 6. TIPC |
| ------------------------------------------------------- |
| |
| tipc_rmem |
| ---------- |
| |
| The TIPC protocol now has a tunable for the receive memory, similar to the |
| tcp_rmem - i.e. a vector of 3 INTEGERs: (min, default, max) |
| |
| # cat /proc/sys/net/tipc/tipc_rmem |
| 4252725 34021800 68043600 |
| # |
| |
| The max value is set to CONN_OVERLOAD_LIMIT, and the default and min values |
| are scaled (shifted) versions of that same value. Note that the min value |
| is not at this point in time used in any meaningful way, but the triplet is |
| preserved in order to be consistent with things like tcp_rmem. |
| |
| named_timeout |
| -------------- |
| |
| TIPC name table updates are distributed asynchronously in a cluster, without |
| any form of transaction handling. This means that different race scenarios are |
| possible. One such is that a name withdrawal sent out by one node and received |
| by another node may arrive after a second, overlapping name publication already |
| has been accepted from a third node, although the conflicting updates |
| originally may have been issued in the correct sequential order. |
| If named_timeout is nonzero, failed topology updates will be placed on a defer |
| queue until another event arrives that clears the error, or until the timeout |
| expires. Value is in milliseconds. |
