drivers/net/ethernet/amd/7990.h - third_party/linux - Git at Google

 /*
  * 7990.h -- LANCE ethernet IC generic routines.
  * This is an attempt to separate out the bits of various ethernet
  * drivers that are common because they all use the AMD 7990 LANCE
  * (Local Area Network Controller for Ethernet) chip.
  *
  * Copyright (C) 05/1998 Peter Maydell <pmaydell@chiark.greenend.org.uk>
  *
  * Most of this stuff was obtained by looking at other LANCE drivers,
  * in particular a2065.[ch]. The AMD C-LANCE datasheet was also helpful.
  */

 #ifndef _7990_H
 #define _7990_H

 /* The lance only has two register locations. We communicate mostly via memory. */
 #define LANCE_RDP	0	/* Register Data Port */
 #define LANCE_RAP	2	/* Register Address Port */

 /* Transmit/receive ring definitions.
  * We allow the specific drivers to override these defaults if they want to.
  * NB: according to lance.c, increasing the number of buffers is a waste
  * of space and reduces the chance that an upper layer will be able to
  * reorder queued Tx packets based on priority. [Clearly there is a minimum
  * limit too: too small and we drop rx packets and can't tx at full speed.]
  * 4+4 seems to be the usual setting; the atarilance driver uses 3 and 5.
  */

 /* Blast! This won't work. The problem is that we can't specify a default
  * setting because that would cause the lance_init_block struct to be
  * too long (and overflow the RAM on shared-memory cards like the HP LANCE.
  */
 #ifndef LANCE_LOG_TX_BUFFERS
 #define LANCE_LOG_TX_BUFFERS 1
 #define LANCE_LOG_RX_BUFFERS 3
 #endif

 #define TX_RING_SIZE		(1 << LANCE_LOG_TX_BUFFERS)
 #define RX_RING_SIZE		(1 << LANCE_LOG_RX_BUFFERS)
 #define TX_RING_MOD_MASK	(TX_RING_SIZE - 1)
 #define RX_RING_MOD_MASK	(RX_RING_SIZE - 1)
 #define TX_RING_LEN_BITS	((LANCE_LOG_TX_BUFFERS) << 29)
 #define RX_RING_LEN_BITS	((LANCE_LOG_RX_BUFFERS) << 29)
 #define PKT_BUFF_SIZE		(1544)
 #define RX_BUFF_SIZE		PKT_BUFF_SIZE
 #define TX_BUFF_SIZE		PKT_BUFF_SIZE

 /* Each receive buffer is described by a receive message descriptor (RMD) */
 struct lance_rx_desc {
 	volatile unsigned short rmd0;	    /* low address of packet */
 	volatile unsigned char  rmd1_bits;  /* descriptor bits */
 	volatile unsigned char  rmd1_hadr;  /* high address of packet */
 	volatile short    length;	    /* This length is 2s complement (negative)!
 					     * Buffer length */
 	volatile unsigned short mblength;   /* Actual number of bytes received */
 };

 /* Ditto for TMD: */
 struct lance_tx_desc {
 	volatile unsigned short tmd0;	    /* low address of packet */
 	volatile unsigned char  tmd1_bits;  /* descriptor bits */
 	volatile unsigned char  tmd1_hadr;  /* high address of packet */
 	volatile short    length;	    /* Length is 2s complement (negative)! */
 	volatile unsigned short misc;
 };

 /* There are three memory structures accessed by the LANCE:
  * the initialization block, the receive and transmit descriptor rings,
  * and the data buffers themselves. In fact we might as well put the
  * init block,the Tx and Rx rings and the buffers together in memory:
  */
 struct lance_init_block {
 	volatile unsigned short mode;		/* Pre-set mode (reg. 15) */
 	volatile unsigned char phys_addr[6];	/* Physical ethernet address */
 	volatile unsigned filter[2];		/* Multicast filter (64 bits) */

 	/* Receive and transmit ring base, along with extra bits. */
 	volatile unsigned short rx_ptr;		/* receive descriptor addr */
 	volatile unsigned short rx_len;		/* receive len and high addr */
 	volatile unsigned short tx_ptr;		/* transmit descriptor addr */
 	volatile unsigned short tx_len;		/* transmit len and high addr */

 	/* The Tx and Rx ring entries must be aligned on 8-byte boundaries.
 	 * This will be true if this whole struct is 8-byte aligned.
 	 */
 	volatile struct lance_tx_desc btx_ring[TX_RING_SIZE];
 	volatile struct lance_rx_desc brx_ring[RX_RING_SIZE];

 	volatile char tx_buf[TX_RING_SIZE][TX_BUFF_SIZE];
 	volatile char rx_buf[RX_RING_SIZE][RX_BUFF_SIZE];
 	/* we use this just to make the struct big enough that we can move its startaddr
 	 * in order to force alignment to an eight byte boundary.
 	 */
 };

 /* This is where we keep all the stuff the driver needs to know about.
  * I'm definitely unhappy about the mechanism for allowing specific
  * drivers to add things...
  */
 struct lance_private {
 	const char *name;
 	unsigned long base;
 	volatile struct lance_init_block *init_block; /* CPU address of RAM */
 	volatile struct lance_init_block *lance_init_block; /* LANCE address of RAM */

 	int rx_new, tx_new;
 	int rx_old, tx_old;

 	int lance_log_rx_bufs, lance_log_tx_bufs;
 	int rx_ring_mod_mask, tx_ring_mod_mask;

 	int tpe;			/* TPE is selected */
 	int auto_select;		/* cable-selection is by carrier */
 	unsigned short busmaster_regval;

 	unsigned int irq;		/* IRQ to register */

 	/* This is because the HP LANCE is disgusting and you have to check
 	 * a DIO-specific register every time you read/write the LANCE regs :-<
 	 * [could we get away with making these some sort of macro?]
 	 */
 	void (*writerap)(void *, unsigned short);
 	void (*writerdp)(void *, unsigned short);
 	unsigned short (*readrdp)(void *);
 	spinlock_t devlock;
 	char tx_full;
 };

 /*
  *		Am7990 Control and Status Registers
  */
 #define LE_CSR0		0x0000	/* LANCE Controller Status */
 #define LE_CSR1		0x0001	/* IADR[15:0] (bit0==0 ie word aligned) */
 #define LE_CSR2		0x0002	/* IADR[23:16] (high bits reserved) */
 #define LE_CSR3		0x0003	/* Misc */

 /*
  *		Bit definitions for CSR0 (LANCE Controller Status)
  */
 #define LE_C0_ERR	0x8000	/* Error = BABL | CERR | MISS | MERR */
 #define LE_C0_BABL	0x4000	/* Babble: Transmitted too many bits */
 #define LE_C0_CERR	0x2000	/* No Heartbeat (10BASE-T) */
 #define LE_C0_MISS	0x1000	/* Missed Frame (no rx buffer to put it in) */
 #define LE_C0_MERR	0x0800	/* Memory Error */
 #define LE_C0_RINT	0x0400	/* Receive Interrupt */
 #define LE_C0_TINT	0x0200	/* Transmit Interrupt */
 #define LE_C0_IDON	0x0100	/* Initialization Done */
 #define LE_C0_INTR	0x0080	/* Interrupt Flag
 				   = BABL | MISS | MERR | RINT | TINT | IDON */
 #define LE_C0_INEA	0x0040	/* Interrupt Enable */
 #define LE_C0_RXON	0x0020	/* Receive On */
 #define LE_C0_TXON	0x0010	/* Transmit On */
 #define LE_C0_TDMD	0x0008	/* Transmit Demand */
 #define LE_C0_STOP	0x0004	/* Stop */
 #define LE_C0_STRT	0x0002	/* Start */
 #define LE_C0_INIT	0x0001	/* Initialize */


 /*
  *		Bit definitions for CSR3
  */
 #define LE_C3_BSWP	0x0004	/* Byte Swap (on for big endian byte order) */
 #define LE_C3_ACON	0x0002	/* ALE Control (on for active low ALE) */
 #define LE_C3_BCON	0x0001	/* Byte Control */


 /*
  *		Mode Flags
  */
 #define LE_MO_PROM	0x8000	/* Promiscuous Mode */
 /* these next ones 0x4000 -- 0x0080 are not available on the LANCE 7990,
  * but they are in NetBSD's am7990.h, presumably for backwards-compatible chips
  */
 #define LE_MO_DRCVBC	0x4000	/* disable receive broadcast */
 #define LE_MO_DRCVPA	0x2000	/* disable physical address detection */
 #define LE_MO_DLNKTST	0x1000	/* disable link status */
 #define LE_MO_DAPC	0x0800	/* disable automatic polarity correction */
 #define LE_MO_MENDECL	0x0400	/* MENDEC loopback mode */
 #define LE_MO_LRTTSEL	0x0200	/* lower RX threshold / TX mode selection */
 #define LE_MO_PSEL1	0x0100	/* port selection bit1 */
 #define LE_MO_PSEL0	0x0080	/* port selection bit0 */
 /* and this one is from the C-LANCE data sheet... */
 #define LE_MO_EMBA	0x0080	/* Enable Modified Backoff Algorithm
 				   (C-LANCE, not original LANCE) */
 #define LE_MO_INTL	0x0040	/* Internal Loopback */
 #define LE_MO_DRTY	0x0020	/* Disable Retry */
 #define LE_MO_FCOLL	0x0010	/* Force Collision */
 #define LE_MO_DXMTFCS	0x0008	/* Disable Transmit CRC */
 #define LE_MO_LOOP	0x0004	/* Loopback Enable */
 #define LE_MO_DTX	0x0002	/* Disable Transmitter */
 #define LE_MO_DRX	0x0001	/* Disable Receiver */


 /*
  *		Receive Flags
  */
 #define LE_R1_OWN	0x80	/* LANCE owns the descriptor */
 #define LE_R1_ERR	0x40	/* Error */
 #define LE_R1_FRA	0x20	/* Framing Error */
 #define LE_R1_OFL	0x10	/* Overflow Error */
 #define LE_R1_CRC	0x08	/* CRC Error */
 #define LE_R1_BUF	0x04	/* Buffer Error */
 #define LE_R1_SOP	0x02	/* Start of Packet */
 #define LE_R1_EOP	0x01	/* End of Packet */
 #define LE_R1_POK	0x03	/* Packet is complete: SOP + EOP */


 /*
  *		Transmit Flags
  */
 #define LE_T1_OWN	0x80	/* LANCE owns the descriptor */
 #define LE_T1_ERR	0x40	/* Error */
 #define LE_T1_RES	0x20	/* Reserved, LANCE writes this with a zero */
 #define LE_T1_EMORE	0x10	/* More than one retry needed */
 #define LE_T1_EONE	0x08	/* One retry needed */
 #define LE_T1_EDEF	0x04	/* Deferred */
 #define LE_T1_SOP	0x02	/* Start of Packet */
 #define LE_T1_EOP	0x01	/* End of Packet */
 #define LE_T1_POK	0x03	/* Packet is complete: SOP + EOP */

 /*
  *		Error Flags
  */
 #define LE_T3_BUF	0x8000	/* Buffer Error */
 #define LE_T3_UFL	0x4000	/* Underflow Error */
 #define LE_T3_LCOL	0x1000	/* Late Collision */
 #define LE_T3_CLOS	0x0800	/* Loss of Carrier */
 #define LE_T3_RTY	0x0400	/* Retry Error */
 #define LE_T3_TDR	0x03ff	/* Time Domain Reflectometry */

 /* Miscellaneous useful macros */

 #define TX_BUFFS_AVAIL ((lp->tx_old <= lp->tx_new) ? \
 			lp->tx_old + lp->tx_ring_mod_mask - lp->tx_new : \
 			lp->tx_old - lp->tx_new - 1)

 /* The LANCE only uses 24 bit addresses. This does the obvious thing. */
 #define LANCE_ADDR(x) ((int)(x) & ~0xff000000)

 /* Now the prototypes we export */
 int lance_open(struct net_device *dev);
 int lance_close(struct net_device *dev);
 int lance_start_xmit(struct sk_buff *skb, struct net_device *dev);
 void lance_set_multicast(struct net_device *dev);
 void lance_tx_timeout(struct net_device *dev);
 #ifdef CONFIG_NET_POLL_CONTROLLER
 void lance_poll(struct net_device *dev);
 #endif

 #endif /* ndef _7990_H */
	/*
	* 7990.h -- LANCE ethernet IC generic routines.
	* This is an attempt to separate out the bits of various ethernet
	* drivers that are common because they all use the AMD 7990 LANCE
	* (Local Area Network Controller for Ethernet) chip.
	*
	* Copyright (C) 05/1998 Peter Maydell <pmaydell@chiark.greenend.org.uk>
	*
	* Most of this stuff was obtained by looking at other LANCE drivers,
	* in particular a2065.[ch]. The AMD C-LANCE datasheet was also helpful.
	*/

	#ifndef _7990_H
	#define _7990_H

	/* The lance only has two register locations. We communicate mostly via memory. */
	#define LANCE_RDP 0 /* Register Data Port */
	#define LANCE_RAP 2 /* Register Address Port */

	/* Transmit/receive ring definitions.
	* We allow the specific drivers to override these defaults if they want to.
	* NB: according to lance.c, increasing the number of buffers is a waste
	* of space and reduces the chance that an upper layer will be able to
	* reorder queued Tx packets based on priority. [Clearly there is a minimum
	* limit too: too small and we drop rx packets and can't tx at full speed.]
	* 4+4 seems to be the usual setting; the atarilance driver uses 3 and 5.
	*/

	/* Blast! This won't work. The problem is that we can't specify a default
	* setting because that would cause the lance_init_block struct to be
	* too long (and overflow the RAM on shared-memory cards like the HP LANCE.
	*/
	#ifndef LANCE_LOG_TX_BUFFERS
	#define LANCE_LOG_TX_BUFFERS 1
	#define LANCE_LOG_RX_BUFFERS 3
	#endif

	#define TX_RING_SIZE (1 << LANCE_LOG_TX_BUFFERS)
	#define RX_RING_SIZE (1 << LANCE_LOG_RX_BUFFERS)
	#define TX_RING_MOD_MASK (TX_RING_SIZE - 1)
	#define RX_RING_MOD_MASK (RX_RING_SIZE - 1)
	#define TX_RING_LEN_BITS ((LANCE_LOG_TX_BUFFERS) << 29)
	#define RX_RING_LEN_BITS ((LANCE_LOG_RX_BUFFERS) << 29)
	#define PKT_BUFF_SIZE (1544)
	#define RX_BUFF_SIZE PKT_BUFF_SIZE
	#define TX_BUFF_SIZE PKT_BUFF_SIZE

	/* Each receive buffer is described by a receive message descriptor (RMD) */
	struct lance_rx_desc {
	volatile unsigned short rmd0; /* low address of packet */
	volatile unsigned char rmd1_bits; /* descriptor bits */
	volatile unsigned char rmd1_hadr; /* high address of packet */
	volatile short length; /* This length is 2s complement (negative)!
	* Buffer length */
	volatile unsigned short mblength; /* Actual number of bytes received */
	};

	/* Ditto for TMD: */
	struct lance_tx_desc {
	volatile unsigned short tmd0; /* low address of packet */
	volatile unsigned char tmd1_bits; /* descriptor bits */
	volatile unsigned char tmd1_hadr; /* high address of packet */
	volatile short length; /* Length is 2s complement (negative)! */
	volatile unsigned short misc;
	};

	/* There are three memory structures accessed by the LANCE:
	* the initialization block, the receive and transmit descriptor rings,
	* and the data buffers themselves. In fact we might as well put the
	* init block,the Tx and Rx rings and the buffers together in memory:
	*/
	struct lance_init_block {
	volatile unsigned short mode; /* Pre-set mode (reg. 15) */
	volatile unsigned char phys_addr[6]; /* Physical ethernet address */
	volatile unsigned filter[2]; /* Multicast filter (64 bits) */

	/* Receive and transmit ring base, along with extra bits. */
	volatile unsigned short rx_ptr; /* receive descriptor addr */
	volatile unsigned short rx_len; /* receive len and high addr */
	volatile unsigned short tx_ptr; /* transmit descriptor addr */
	volatile unsigned short tx_len; /* transmit len and high addr */

	/* The Tx and Rx ring entries must be aligned on 8-byte boundaries.
	* This will be true if this whole struct is 8-byte aligned.
	*/
	volatile struct lance_tx_desc btx_ring[TX_RING_SIZE];
	volatile struct lance_rx_desc brx_ring[RX_RING_SIZE];

	volatile char tx_buf[TX_RING_SIZE][TX_BUFF_SIZE];
	volatile char rx_buf[RX_RING_SIZE][RX_BUFF_SIZE];
	/* we use this just to make the struct big enough that we can move its startaddr
	* in order to force alignment to an eight byte boundary.
	*/
	};

	/* This is where we keep all the stuff the driver needs to know about.
	* I'm definitely unhappy about the mechanism for allowing specific
	* drivers to add things...
	*/
	struct lance_private {
	const char *name;
	unsigned long base;
	volatile struct lance_init_block init_block; / CPU address of RAM */
	volatile struct lance_init_block lance_init_block; / LANCE address of RAM */

	int rx_new, tx_new;
	int rx_old, tx_old;

	int lance_log_rx_bufs, lance_log_tx_bufs;
	int rx_ring_mod_mask, tx_ring_mod_mask;

	int tpe; /* TPE is selected */
	int auto_select; /* cable-selection is by carrier */
	unsigned short busmaster_regval;

	unsigned int irq; /* IRQ to register */

	/* This is because the HP LANCE is disgusting and you have to check
	* a DIO-specific register every time you read/write the LANCE regs :-<
	* [could we get away with making these some sort of macro?]
	*/
	void (writerap)(void , unsigned short);
	void (writerdp)(void , unsigned short);
	unsigned short (readrdp)(void );
	spinlock_t devlock;
	char tx_full;
	};

	/*
	* Am7990 Control and Status Registers
	*/
	#define LE_CSR0 0x0000 /* LANCE Controller Status */
	#define LE_CSR1 0x0001 /* IADR[15:0] (bit0==0 ie word aligned) */
	#define LE_CSR2 0x0002 /* IADR[23:16] (high bits reserved) */
	#define LE_CSR3 0x0003 /* Misc */

	/*
	* Bit definitions for CSR0 (LANCE Controller Status)
	*/
	#define LE_C0_ERR 0x8000 /* Error = BABL \| CERR \| MISS \| MERR */
	#define LE_C0_BABL 0x4000 /* Babble: Transmitted too many bits */
	#define LE_C0_CERR 0x2000 /* No Heartbeat (10BASE-T) */
	#define LE_C0_MISS 0x1000 /* Missed Frame (no rx buffer to put it in) */
	#define LE_C0_MERR 0x0800 /* Memory Error */
	#define LE_C0_RINT 0x0400 /* Receive Interrupt */
	#define LE_C0_TINT 0x0200 /* Transmit Interrupt */
	#define LE_C0_IDON 0x0100 /* Initialization Done */
	#define LE_C0_INTR 0x0080 /* Interrupt Flag
	= BABL \| MISS \| MERR \| RINT \| TINT \| IDON */
	#define LE_C0_INEA 0x0040 /* Interrupt Enable */
	#define LE_C0_RXON 0x0020 /* Receive On */
	#define LE_C0_TXON 0x0010 /* Transmit On */
	#define LE_C0_TDMD 0x0008 /* Transmit Demand */
	#define LE_C0_STOP 0x0004 /* Stop */
	#define LE_C0_STRT 0x0002 /* Start */
	#define LE_C0_INIT 0x0001 /* Initialize */


	/*
	* Bit definitions for CSR3
	*/
	#define LE_C3_BSWP 0x0004 /* Byte Swap (on for big endian byte order) */
	#define LE_C3_ACON 0x0002 /* ALE Control (on for active low ALE) */
	#define LE_C3_BCON 0x0001 /* Byte Control */


	/*
	* Mode Flags
	*/
	#define LE_MO_PROM 0x8000 /* Promiscuous Mode */
	/* these next ones 0x4000 -- 0x0080 are not available on the LANCE 7990,
	* but they are in NetBSD's am7990.h, presumably for backwards-compatible chips
	*/
	#define LE_MO_DRCVBC 0x4000 /* disable receive broadcast */
	#define LE_MO_DRCVPA 0x2000 /* disable physical address detection */
	#define LE_MO_DLNKTST 0x1000 /* disable link status */
	#define LE_MO_DAPC 0x0800 /* disable automatic polarity correction */
	#define LE_MO_MENDECL 0x0400 /* MENDEC loopback mode */
	#define LE_MO_LRTTSEL 0x0200 /* lower RX threshold / TX mode selection */
	#define LE_MO_PSEL1 0x0100 /* port selection bit1 */
	#define LE_MO_PSEL0 0x0080 /* port selection bit0 */
	/* and this one is from the C-LANCE data sheet... */
	#define LE_MO_EMBA 0x0080 /* Enable Modified Backoff Algorithm
	(C-LANCE, not original LANCE) */
	#define LE_MO_INTL 0x0040 /* Internal Loopback */
	#define LE_MO_DRTY 0x0020 /* Disable Retry */
	#define LE_MO_FCOLL 0x0010 /* Force Collision */
	#define LE_MO_DXMTFCS 0x0008 /* Disable Transmit CRC */
	#define LE_MO_LOOP 0x0004 /* Loopback Enable */
	#define LE_MO_DTX 0x0002 /* Disable Transmitter */
	#define LE_MO_DRX 0x0001 /* Disable Receiver */


	/*
	* Receive Flags
	*/
	#define LE_R1_OWN 0x80 /* LANCE owns the descriptor */
	#define LE_R1_ERR 0x40 /* Error */
	#define LE_R1_FRA 0x20 /* Framing Error */
	#define LE_R1_OFL 0x10 /* Overflow Error */
	#define LE_R1_CRC 0x08 /* CRC Error */
	#define LE_R1_BUF 0x04 /* Buffer Error */
	#define LE_R1_SOP 0x02 /* Start of Packet */
	#define LE_R1_EOP 0x01 /* End of Packet */
	#define LE_R1_POK 0x03 /* Packet is complete: SOP + EOP */


	/*
	* Transmit Flags
	*/
	#define LE_T1_OWN 0x80 /* LANCE owns the descriptor */
	#define LE_T1_ERR 0x40 /* Error */
	#define LE_T1_RES 0x20 /* Reserved, LANCE writes this with a zero */
	#define LE_T1_EMORE 0x10 /* More than one retry needed */
	#define LE_T1_EONE 0x08 /* One retry needed */
	#define LE_T1_EDEF 0x04 /* Deferred */
	#define LE_T1_SOP 0x02 /* Start of Packet */
	#define LE_T1_EOP 0x01 /* End of Packet */
	#define LE_T1_POK 0x03 /* Packet is complete: SOP + EOP */

	/*
	* Error Flags
	*/
	#define LE_T3_BUF 0x8000 /* Buffer Error */
	#define LE_T3_UFL 0x4000 /* Underflow Error */
	#define LE_T3_LCOL 0x1000 /* Late Collision */
	#define LE_T3_CLOS 0x0800 /* Loss of Carrier */
	#define LE_T3_RTY 0x0400 /* Retry Error */
	#define LE_T3_TDR 0x03ff /* Time Domain Reflectometry */

	/* Miscellaneous useful macros */

	#define TX_BUFFS_AVAIL ((lp->tx_old <= lp->tx_new) ? \
	lp->tx_old + lp->tx_ring_mod_mask - lp->tx_new : \
	lp->tx_old - lp->tx_new - 1)

	/* The LANCE only uses 24 bit addresses. This does the obvious thing. */
	#define LANCE_ADDR(x) ((int)(x) & ~0xff000000)

	/* Now the prototypes we export */
	int lance_open(struct net_device *dev);
	int lance_close(struct net_device *dev);
	int lance_start_xmit(struct sk_buff skb, struct net_device dev);
	void lance_set_multicast(struct net_device *dev);
	void lance_tx_timeout(struct net_device *dev);
	#ifdef CONFIG_NET_POLL_CONTROLLER
	void lance_poll(struct net_device *dev);
	#endif

	#endif /* ndef _7990_H */