|  | /* | 
|  | * sound/oss/pss.c | 
|  | * | 
|  | * The low level driver for the Personal Sound System (ECHO ESC614). | 
|  | * | 
|  | * | 
|  | * Copyright (C) by Hannu Savolainen 1993-1997 | 
|  | * | 
|  | * OSS/Free for Linux is distributed under the GNU GENERAL PUBLIC LICENSE (GPL) | 
|  | * Version 2 (June 1991). See the "COPYING" file distributed with this software | 
|  | * for more info. | 
|  | * | 
|  | * | 
|  | * Thomas Sailer	ioctl code reworked (vmalloc/vfree removed) | 
|  | * Alan Cox		modularisation, clean up. | 
|  | * | 
|  | * 98-02-21: Vladimir Michl <vladimir.michl@upol.cz> | 
|  | *          Added mixer device for Beethoven ADSP-16 (master volume, | 
|  | *	    bass, treble, synth), only for speakers. | 
|  | *          Fixed bug in pss_write (exchange parameters) | 
|  | *          Fixed config port of SB | 
|  | *          Requested two regions for PSS (PSS mixer, PSS config) | 
|  | *          Modified pss_download_boot | 
|  | *          To probe_pss_mss added test for initialize AD1848 | 
|  | * 98-05-28: Vladimir Michl <vladimir.michl@upol.cz> | 
|  | *          Fixed computation of mixer volumes | 
|  | * 04-05-1999: Anthony Barbachan <barbcode@xmen.cis.fordham.edu> | 
|  | *          Added code that allows the user to enable his cdrom and/or | 
|  | *          joystick through the module parameters pss_cdrom_port and | 
|  | *          pss_enable_joystick.  pss_cdrom_port takes a port address as its | 
|  | *          argument.  pss_enable_joystick takes either a 0 or a non-0 as its | 
|  | *          argument. | 
|  | * 04-06-1999: Anthony Barbachan <barbcode@xmen.cis.fordham.edu> | 
|  | *          Separated some code into new functions for easier reuse. | 
|  | *          Cleaned up and streamlined new code.  Added code to allow a user | 
|  | *          to only use this driver for enabling non-sound components | 
|  | *          through the new module parameter pss_no_sound (flag).  Added | 
|  | *          code that would allow a user to decide whether the driver should | 
|  | *          reset the configured hardware settings for the PSS board through | 
|  | *          the module parameter pss_keep_settings (flag).   This flag will | 
|  | *          allow a user to free up resources in use by this card if needbe, | 
|  | *          furthermore it allows him to use this driver to just enable the | 
|  | *          emulations and then be unloaded as it is no longer needed.  Both | 
|  | *          new settings are only available to this driver if compiled as a | 
|  | *          module.  The default settings of all new parameters are set to | 
|  | *          load the driver as it did in previous versions. | 
|  | * 04-07-1999: Anthony Barbachan <barbcode@xmen.cis.fordham.edu> | 
|  | *          Added module parameter pss_firmware to allow the user to tell | 
|  | *          the driver where the fireware file is located.  The default | 
|  | *          setting is the previous hardcoded setting "/etc/sound/pss_synth". | 
|  | * 00-03-03: Christoph Hellwig <chhellwig@infradead.org> | 
|  | *	    Adapted to module_init/module_exit | 
|  | * 11-10-2000: Bartlomiej Zolnierkiewicz <bkz@linux-ide.org> | 
|  | *	    Added __init to probe_pss(), attach_pss() and probe_pss_mpu() | 
|  | * 02-Jan-2001: Chris Rankin | 
|  | *          Specify that this module owns the coprocessor | 
|  | */ | 
|  |  | 
|  |  | 
|  | #include <linux/init.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/spinlock.h> | 
|  |  | 
|  | #include "sound_config.h" | 
|  | #include "sound_firmware.h" | 
|  |  | 
|  | #include "ad1848.h" | 
|  | #include "mpu401.h" | 
|  |  | 
|  | /* | 
|  | * PSS registers. | 
|  | */ | 
|  | #define REG(x)	(devc->base+x) | 
|  | #define	PSS_DATA	0 | 
|  | #define	PSS_STATUS	2 | 
|  | #define PSS_CONTROL	2 | 
|  | #define	PSS_ID		4 | 
|  | #define	PSS_IRQACK	4 | 
|  | #define	PSS_PIO		0x1a | 
|  |  | 
|  | /* | 
|  | * Config registers | 
|  | */ | 
|  | #define CONF_PSS	0x10 | 
|  | #define CONF_WSS	0x12 | 
|  | #define CONF_SB		0x14 | 
|  | #define CONF_CDROM	0x16 | 
|  | #define CONF_MIDI	0x18 | 
|  |  | 
|  | /* | 
|  | * Status bits. | 
|  | */ | 
|  | #define PSS_FLAG3     0x0800 | 
|  | #define PSS_FLAG2     0x0400 | 
|  | #define PSS_FLAG1     0x1000 | 
|  | #define PSS_FLAG0     0x0800 | 
|  | #define PSS_WRITE_EMPTY  0x8000 | 
|  | #define PSS_READ_FULL    0x4000 | 
|  |  | 
|  | /* | 
|  | * WSS registers | 
|  | */ | 
|  | #define WSS_INDEX 4 | 
|  | #define WSS_DATA 5 | 
|  |  | 
|  | /* | 
|  | * WSS status bits | 
|  | */ | 
|  | #define WSS_INITIALIZING 0x80 | 
|  | #define WSS_AUTOCALIBRATION 0x20 | 
|  |  | 
|  | #define NO_WSS_MIXER	-1 | 
|  |  | 
|  | #include "coproc.h" | 
|  |  | 
|  | #include "pss_boot.h" | 
|  |  | 
|  | /* If compiled into kernel, it enable or disable pss mixer */ | 
|  | #ifdef CONFIG_PSS_MIXER | 
|  | static int pss_mixer = 1; | 
|  | #else | 
|  | static int pss_mixer; | 
|  | #endif | 
|  |  | 
|  |  | 
|  | typedef struct pss_mixerdata { | 
|  | unsigned int volume_l; | 
|  | unsigned int volume_r; | 
|  | unsigned int bass; | 
|  | unsigned int treble; | 
|  | unsigned int synth; | 
|  | } pss_mixerdata; | 
|  |  | 
|  | typedef struct pss_confdata { | 
|  | int             base; | 
|  | int             irq; | 
|  | int             dma; | 
|  | int            *osp; | 
|  | pss_mixerdata   mixer; | 
|  | int             ad_mixer_dev; | 
|  | } pss_confdata; | 
|  |  | 
|  | static pss_confdata pss_data; | 
|  | static pss_confdata *devc = &pss_data; | 
|  | static DEFINE_SPINLOCK(lock); | 
|  |  | 
|  | static int      pss_initialized; | 
|  | static int      nonstandard_microcode; | 
|  | static int	pss_cdrom_port = -1;	/* Parameter for the PSS cdrom port */ | 
|  | static int	pss_enable_joystick;    /* Parameter for enabling the joystick */ | 
|  | static coproc_operations pss_coproc_operations; | 
|  |  | 
|  | static void pss_write(pss_confdata *devc, int data) | 
|  | { | 
|  | unsigned long i, limit; | 
|  |  | 
|  | limit = jiffies + HZ/10;	/* The timeout is 0.1 seconds */ | 
|  | /* | 
|  | * Note! the i<5000000 is an emergency exit. The dsp_command() is sometimes | 
|  | * called while interrupts are disabled. This means that the timer is | 
|  | * disabled also. However the timeout situation is a abnormal condition. | 
|  | * Normally the DSP should be ready to accept commands after just couple of | 
|  | * loops. | 
|  | */ | 
|  |  | 
|  | for (i = 0; i < 5000000 && time_before(jiffies, limit); i++) | 
|  | { | 
|  | if (inw(REG(PSS_STATUS)) & PSS_WRITE_EMPTY) | 
|  | { | 
|  | outw(data, REG(PSS_DATA)); | 
|  | return; | 
|  | } | 
|  | } | 
|  | printk(KERN_WARNING "PSS: DSP Command (%04x) Timeout.\n", data); | 
|  | } | 
|  |  | 
|  | static int __init probe_pss(struct address_info *hw_config) | 
|  | { | 
|  | unsigned short id; | 
|  | int irq, dma; | 
|  |  | 
|  | devc->base = hw_config->io_base; | 
|  | irq = devc->irq = hw_config->irq; | 
|  | dma = devc->dma = hw_config->dma; | 
|  | devc->osp = hw_config->osp; | 
|  |  | 
|  | if (devc->base != 0x220 && devc->base != 0x240) | 
|  | if (devc->base != 0x230 && devc->base != 0x250)		/* Some cards use these */ | 
|  | return 0; | 
|  |  | 
|  | if (!request_region(devc->base, 0x10, "PSS mixer, SB emulation")) { | 
|  | printk(KERN_ERR "PSS: I/O port conflict\n"); | 
|  | return 0; | 
|  | } | 
|  | id = inw(REG(PSS_ID)); | 
|  | if ((id >> 8) != 'E') { | 
|  | printk(KERN_ERR "No PSS signature detected at 0x%x (0x%x)\n",  devc->base,  id); | 
|  | release_region(devc->base, 0x10); | 
|  | return 0; | 
|  | } | 
|  | if (!request_region(devc->base + 0x10, 0x9, "PSS config")) { | 
|  | printk(KERN_ERR "PSS: I/O port conflict\n"); | 
|  | release_region(devc->base, 0x10); | 
|  | return 0; | 
|  | } | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static int set_irq(pss_confdata * devc, int dev, int irq) | 
|  | { | 
|  | static unsigned short irq_bits[16] = | 
|  | { | 
|  | 0x0000, 0x0000, 0x0000, 0x0008, | 
|  | 0x0000, 0x0010, 0x0000, 0x0018, | 
|  | 0x0000, 0x0020, 0x0028, 0x0030, | 
|  | 0x0038, 0x0000, 0x0000, 0x0000 | 
|  | }; | 
|  |  | 
|  | unsigned short  tmp, bits; | 
|  |  | 
|  | if (irq < 0 || irq > 15) | 
|  | return 0; | 
|  |  | 
|  | tmp = inw(REG(dev)) & ~0x38;	/* Load confreg, mask IRQ bits out */ | 
|  |  | 
|  | if ((bits = irq_bits[irq]) == 0 && irq != 0) | 
|  | { | 
|  | printk(KERN_ERR "PSS: Invalid IRQ %d\n", irq); | 
|  | return 0; | 
|  | } | 
|  | outw(tmp | bits, REG(dev)); | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static int set_io_base(pss_confdata * devc, int dev, int base) | 
|  | { | 
|  | unsigned short  tmp = inw(REG(dev)) & 0x003f; | 
|  | unsigned short  bits = (base & 0x0ffc) << 4; | 
|  |  | 
|  | outw(bits | tmp, REG(dev)); | 
|  |  | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static int set_dma(pss_confdata * devc, int dev, int dma) | 
|  | { | 
|  | static unsigned short dma_bits[8] = | 
|  | { | 
|  | 0x0001, 0x0002, 0x0000, 0x0003, | 
|  | 0x0000, 0x0005, 0x0006, 0x0007 | 
|  | }; | 
|  |  | 
|  | unsigned short  tmp, bits; | 
|  |  | 
|  | if (dma < 0 || dma > 7) | 
|  | return 0; | 
|  |  | 
|  | tmp = inw(REG(dev)) & ~0x07;	/* Load confreg, mask DMA bits out */ | 
|  |  | 
|  | if ((bits = dma_bits[dma]) == 0 && dma != 4) | 
|  | { | 
|  | printk(KERN_ERR "PSS: Invalid DMA %d\n", dma); | 
|  | return 0; | 
|  | } | 
|  | outw(tmp | bits, REG(dev)); | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static int pss_reset_dsp(pss_confdata * devc) | 
|  | { | 
|  | unsigned long   i, limit = jiffies + HZ/10; | 
|  |  | 
|  | outw(0x2000, REG(PSS_CONTROL)); | 
|  | for (i = 0; i < 32768 && (limit-jiffies >= 0); i++) | 
|  | inw(REG(PSS_CONTROL)); | 
|  | outw(0x0000, REG(PSS_CONTROL)); | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static int pss_put_dspword(pss_confdata * devc, unsigned short word) | 
|  | { | 
|  | int i, val; | 
|  |  | 
|  | for (i = 0; i < 327680; i++) | 
|  | { | 
|  | val = inw(REG(PSS_STATUS)); | 
|  | if (val & PSS_WRITE_EMPTY) | 
|  | { | 
|  | outw(word, REG(PSS_DATA)); | 
|  | return 1; | 
|  | } | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pss_get_dspword(pss_confdata * devc, unsigned short *word) | 
|  | { | 
|  | int i, val; | 
|  |  | 
|  | for (i = 0; i < 327680; i++) | 
|  | { | 
|  | val = inw(REG(PSS_STATUS)); | 
|  | if (val & PSS_READ_FULL) | 
|  | { | 
|  | *word = inw(REG(PSS_DATA)); | 
|  | return 1; | 
|  | } | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pss_download_boot(pss_confdata * devc, unsigned char *block, int size, int flags) | 
|  | { | 
|  | int i, val, count; | 
|  | unsigned long limit; | 
|  |  | 
|  | if (flags & CPF_FIRST) | 
|  | { | 
|  | /*_____ Warn DSP software that a boot is coming */ | 
|  | outw(0x00fe, REG(PSS_DATA)); | 
|  |  | 
|  | limit = jiffies + HZ/10; | 
|  | for (i = 0; i < 32768 && time_before(jiffies, limit); i++) | 
|  | if (inw(REG(PSS_DATA)) == 0x5500) | 
|  | break; | 
|  |  | 
|  | outw(*block++, REG(PSS_DATA)); | 
|  | pss_reset_dsp(devc); | 
|  | } | 
|  | count = 1; | 
|  | while ((flags&CPF_LAST) || count<size ) | 
|  | { | 
|  | int j; | 
|  |  | 
|  | for (j = 0; j < 327670; j++) | 
|  | { | 
|  | /*_____ Wait for BG to appear */ | 
|  | if (inw(REG(PSS_STATUS)) & PSS_FLAG3) | 
|  | break; | 
|  | } | 
|  |  | 
|  | if (j == 327670) | 
|  | { | 
|  | /* It's ok we timed out when the file was empty */ | 
|  | if (count >= size && flags & CPF_LAST) | 
|  | break; | 
|  | else | 
|  | { | 
|  | printk("\n"); | 
|  | printk(KERN_ERR "PSS: Download timeout problems, byte %d=%d\n", count, size); | 
|  | return 0; | 
|  | } | 
|  | } | 
|  | /*_____ Send the next byte */ | 
|  | if (count >= size) | 
|  | { | 
|  | /* If not data in block send 0xffff */ | 
|  | outw (0xffff, REG (PSS_DATA)); | 
|  | } | 
|  | else | 
|  | { | 
|  | /*_____ Send the next byte */ | 
|  | outw (*block++, REG (PSS_DATA)); | 
|  | }; | 
|  | count++; | 
|  | } | 
|  |  | 
|  | if (flags & CPF_LAST) | 
|  | { | 
|  | /*_____ Why */ | 
|  | outw(0, REG(PSS_DATA)); | 
|  |  | 
|  | limit = jiffies + HZ/10; | 
|  | for (i = 0; i < 32768 && (limit - jiffies >= 0); i++) | 
|  | val = inw(REG(PSS_STATUS)); | 
|  |  | 
|  | limit = jiffies + HZ/10; | 
|  | for (i = 0; i < 32768 && (limit-jiffies >= 0); i++) | 
|  | { | 
|  | val = inw(REG(PSS_STATUS)); | 
|  | if (val & 0x4000) | 
|  | break; | 
|  | } | 
|  |  | 
|  | /* now read the version */ | 
|  | for (i = 0; i < 32000; i++) | 
|  | { | 
|  | val = inw(REG(PSS_STATUS)); | 
|  | if (val & PSS_READ_FULL) | 
|  | break; | 
|  | } | 
|  | if (i == 32000) | 
|  | return 0; | 
|  |  | 
|  | val = inw(REG(PSS_DATA)); | 
|  | /* printk( "<PSS: microcode version %d.%d loaded>",  val/16,  val % 16); */ | 
|  | } | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | /* Mixer */ | 
|  | static void set_master_volume(pss_confdata *devc, int left, int right) | 
|  | { | 
|  | static unsigned char log_scale[101] =  { | 
|  | 0xdb, 0xe0, 0xe3, 0xe5, 0xe7, 0xe9, 0xea, 0xeb, 0xec, 0xed, 0xed, 0xee, | 
|  | 0xef, 0xef, 0xf0, 0xf0, 0xf1, 0xf1, 0xf2, 0xf2, 0xf2, 0xf3, 0xf3, 0xf3, | 
|  | 0xf4, 0xf4, 0xf4, 0xf5, 0xf5, 0xf5, 0xf5, 0xf6, 0xf6, 0xf6, 0xf6, 0xf7, | 
|  | 0xf7, 0xf7, 0xf7, 0xf7, 0xf8, 0xf8, 0xf8, 0xf8, 0xf8, 0xf9, 0xf9, 0xf9, | 
|  | 0xf9, 0xf9, 0xf9, 0xfa, 0xfa, 0xfa, 0xfa, 0xfa, 0xfa, 0xfa, 0xfb, 0xfb, | 
|  | 0xfb, 0xfb, 0xfb, 0xfb, 0xfb, 0xfb, 0xfc, 0xfc, 0xfc, 0xfc, 0xfc, 0xfc, | 
|  | 0xfc, 0xfc, 0xfc, 0xfc, 0xfd, 0xfd, 0xfd, 0xfd, 0xfd, 0xfd, 0xfd, 0xfd, | 
|  | 0xfd, 0xfd, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, | 
|  | 0xfe, 0xfe, 0xff, 0xff, 0xff | 
|  | }; | 
|  | pss_write(devc, 0x0010); | 
|  | pss_write(devc, log_scale[left] | 0x0000); | 
|  | pss_write(devc, 0x0010); | 
|  | pss_write(devc, log_scale[right] | 0x0100); | 
|  | } | 
|  |  | 
|  | static void set_synth_volume(pss_confdata *devc, int volume) | 
|  | { | 
|  | int vol = ((0x8000*volume)/100L); | 
|  | pss_write(devc, 0x0080); | 
|  | pss_write(devc, vol); | 
|  | pss_write(devc, 0x0081); | 
|  | pss_write(devc, vol); | 
|  | } | 
|  |  | 
|  | static void set_bass(pss_confdata *devc, int level) | 
|  | { | 
|  | int vol = (int)(((0xfd - 0xf0) * level)/100L) + 0xf0; | 
|  | pss_write(devc, 0x0010); | 
|  | pss_write(devc, vol | 0x0200); | 
|  | }; | 
|  |  | 
|  | static void set_treble(pss_confdata *devc, int level) | 
|  | { | 
|  | int vol = (((0xfd - 0xf0) * level)/100L) + 0xf0; | 
|  | pss_write(devc, 0x0010); | 
|  | pss_write(devc, vol | 0x0300); | 
|  | }; | 
|  |  | 
|  | static void pss_mixer_reset(pss_confdata *devc) | 
|  | { | 
|  | set_master_volume(devc, 33, 33); | 
|  | set_bass(devc, 50); | 
|  | set_treble(devc, 50); | 
|  | set_synth_volume(devc, 30); | 
|  | pss_write (devc, 0x0010); | 
|  | pss_write (devc, 0x0800 | 0xce);	/* Stereo */ | 
|  |  | 
|  | if(pss_mixer) | 
|  | { | 
|  | devc->mixer.volume_l = devc->mixer.volume_r = 33; | 
|  | devc->mixer.bass = 50; | 
|  | devc->mixer.treble = 50; | 
|  | devc->mixer.synth = 30; | 
|  | } | 
|  | } | 
|  |  | 
|  | static int set_volume_mono(unsigned __user *p, int *aleft) | 
|  | { | 
|  | int left; | 
|  | unsigned volume; | 
|  | if (get_user(volume, p)) | 
|  | return -EFAULT; | 
|  |  | 
|  | left = volume & 0xff; | 
|  | if (left > 100) | 
|  | left = 100; | 
|  | *aleft = left; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int set_volume_stereo(unsigned __user *p, int *aleft, int *aright) | 
|  | { | 
|  | int left, right; | 
|  | unsigned volume; | 
|  | if (get_user(volume, p)) | 
|  | return -EFAULT; | 
|  |  | 
|  | left = volume & 0xff; | 
|  | if (left > 100) | 
|  | left = 100; | 
|  | right = (volume >> 8) & 0xff; | 
|  | if (right > 100) | 
|  | right = 100; | 
|  | *aleft = left; | 
|  | *aright = right; | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int ret_vol_mono(int left) | 
|  | { | 
|  | return ((left << 8) | left); | 
|  | } | 
|  |  | 
|  | static int ret_vol_stereo(int left, int right) | 
|  | { | 
|  | return ((right << 8) | left); | 
|  | } | 
|  |  | 
|  | static int call_ad_mixer(pss_confdata *devc,unsigned int cmd, void __user *arg) | 
|  | { | 
|  | if (devc->ad_mixer_dev != NO_WSS_MIXER) | 
|  | return mixer_devs[devc->ad_mixer_dev]->ioctl(devc->ad_mixer_dev, cmd, arg); | 
|  | else | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | static int pss_mixer_ioctl (int dev, unsigned int cmd, void __user *arg) | 
|  | { | 
|  | pss_confdata *devc = mixer_devs[dev]->devc; | 
|  | int cmdf = cmd & 0xff; | 
|  |  | 
|  | if ((cmdf != SOUND_MIXER_VOLUME) && (cmdf != SOUND_MIXER_BASS) && | 
|  | (cmdf != SOUND_MIXER_TREBLE) && (cmdf != SOUND_MIXER_SYNTH) && | 
|  | (cmdf != SOUND_MIXER_DEVMASK) && (cmdf != SOUND_MIXER_STEREODEVS) && | 
|  | (cmdf != SOUND_MIXER_RECMASK) && (cmdf != SOUND_MIXER_CAPS) && | 
|  | (cmdf != SOUND_MIXER_RECSRC)) | 
|  | { | 
|  | return call_ad_mixer(devc, cmd, arg); | 
|  | } | 
|  |  | 
|  | if (((cmd >> 8) & 0xff) != 'M') | 
|  | return -EINVAL; | 
|  |  | 
|  | if (_SIOC_DIR (cmd) & _SIOC_WRITE) | 
|  | { | 
|  | switch (cmdf) | 
|  | { | 
|  | case SOUND_MIXER_RECSRC: | 
|  | if (devc->ad_mixer_dev != NO_WSS_MIXER) | 
|  | return call_ad_mixer(devc, cmd, arg); | 
|  | else | 
|  | { | 
|  | int v; | 
|  | if (get_user(v, (int __user *)arg)) | 
|  | return -EFAULT; | 
|  | if (v != 0) | 
|  | return -EINVAL; | 
|  | return 0; | 
|  | } | 
|  | case SOUND_MIXER_VOLUME: | 
|  | if (set_volume_stereo(arg, | 
|  | &devc->mixer.volume_l, | 
|  | &devc->mixer.volume_r)) | 
|  | return -EFAULT; | 
|  | set_master_volume(devc, devc->mixer.volume_l, | 
|  | devc->mixer.volume_r); | 
|  | return ret_vol_stereo(devc->mixer.volume_l, | 
|  | devc->mixer.volume_r); | 
|  |  | 
|  | case SOUND_MIXER_BASS: | 
|  | if (set_volume_mono(arg, &devc->mixer.bass)) | 
|  | return -EFAULT; | 
|  | set_bass(devc, devc->mixer.bass); | 
|  | return ret_vol_mono(devc->mixer.bass); | 
|  |  | 
|  | case SOUND_MIXER_TREBLE: | 
|  | if (set_volume_mono(arg, &devc->mixer.treble)) | 
|  | return -EFAULT; | 
|  | set_treble(devc, devc->mixer.treble); | 
|  | return ret_vol_mono(devc->mixer.treble); | 
|  |  | 
|  | case SOUND_MIXER_SYNTH: | 
|  | if (set_volume_mono(arg, &devc->mixer.synth)) | 
|  | return -EFAULT; | 
|  | set_synth_volume(devc, devc->mixer.synth); | 
|  | return ret_vol_mono(devc->mixer.synth); | 
|  |  | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  | } | 
|  | else | 
|  | { | 
|  | int val, and_mask = 0, or_mask = 0; | 
|  | /* | 
|  | * Return parameters | 
|  | */ | 
|  | switch (cmdf) | 
|  | { | 
|  | case SOUND_MIXER_DEVMASK: | 
|  | if (call_ad_mixer(devc, cmd, arg) == -EINVAL) | 
|  | break; | 
|  | and_mask = ~0; | 
|  | or_mask = SOUND_MASK_VOLUME | SOUND_MASK_BASS | SOUND_MASK_TREBLE | SOUND_MASK_SYNTH; | 
|  | break; | 
|  |  | 
|  | case SOUND_MIXER_STEREODEVS: | 
|  | if (call_ad_mixer(devc, cmd, arg) == -EINVAL) | 
|  | break; | 
|  | and_mask = ~0; | 
|  | or_mask = SOUND_MASK_VOLUME; | 
|  | break; | 
|  |  | 
|  | case SOUND_MIXER_RECMASK: | 
|  | if (devc->ad_mixer_dev != NO_WSS_MIXER) | 
|  | return call_ad_mixer(devc, cmd, arg); | 
|  | break; | 
|  |  | 
|  | case SOUND_MIXER_CAPS: | 
|  | if (devc->ad_mixer_dev != NO_WSS_MIXER) | 
|  | return call_ad_mixer(devc, cmd, arg); | 
|  | or_mask = SOUND_CAP_EXCL_INPUT; | 
|  | break; | 
|  |  | 
|  | case SOUND_MIXER_RECSRC: | 
|  | if (devc->ad_mixer_dev != NO_WSS_MIXER) | 
|  | return call_ad_mixer(devc, cmd, arg); | 
|  | break; | 
|  |  | 
|  | case SOUND_MIXER_VOLUME: | 
|  | or_mask =  ret_vol_stereo(devc->mixer.volume_l, devc->mixer.volume_r); | 
|  | break; | 
|  |  | 
|  | case SOUND_MIXER_BASS: | 
|  | or_mask =  ret_vol_mono(devc->mixer.bass); | 
|  | break; | 
|  |  | 
|  | case SOUND_MIXER_TREBLE: | 
|  | or_mask = ret_vol_mono(devc->mixer.treble); | 
|  | break; | 
|  |  | 
|  | case SOUND_MIXER_SYNTH: | 
|  | or_mask = ret_vol_mono(devc->mixer.synth); | 
|  | break; | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  | if (get_user(val, (int __user *)arg)) | 
|  | return -EFAULT; | 
|  | val &= and_mask; | 
|  | val |= or_mask; | 
|  | if (put_user(val, (int __user *)arg)) | 
|  | return -EFAULT; | 
|  | return val; | 
|  | } | 
|  | } | 
|  |  | 
|  | static struct mixer_operations pss_mixer_operations = | 
|  | { | 
|  | .owner	= THIS_MODULE, | 
|  | .id	= "SOUNDPORT", | 
|  | .name	= "PSS-AD1848", | 
|  | .ioctl	= pss_mixer_ioctl | 
|  | }; | 
|  |  | 
|  | static void disable_all_emulations(void) | 
|  | { | 
|  | outw(0x0000, REG(CONF_PSS));	/* 0x0400 enables joystick */ | 
|  | outw(0x0000, REG(CONF_WSS)); | 
|  | outw(0x0000, REG(CONF_SB)); | 
|  | outw(0x0000, REG(CONF_MIDI)); | 
|  | outw(0x0000, REG(CONF_CDROM)); | 
|  | } | 
|  |  | 
|  | static void configure_nonsound_components(void) | 
|  | { | 
|  | /* Configure Joystick port */ | 
|  |  | 
|  | if(pss_enable_joystick) | 
|  | { | 
|  | outw(0x0400, REG(CONF_PSS));	/* 0x0400 enables joystick */ | 
|  | printk(KERN_INFO "PSS: joystick enabled.\n"); | 
|  | } | 
|  | else | 
|  | { | 
|  | printk(KERN_INFO "PSS: joystick port not enabled.\n"); | 
|  | } | 
|  |  | 
|  | /* Configure CDROM port */ | 
|  |  | 
|  | if(pss_cdrom_port == -1)	/* If cdrom port enablation wasn't requested */ | 
|  | { | 
|  | printk(KERN_INFO "PSS: CDROM port not enabled.\n"); | 
|  | } | 
|  | else if(check_region(pss_cdrom_port, 2)) | 
|  | { | 
|  | printk(KERN_ERR "PSS: CDROM I/O port conflict.\n"); | 
|  | } | 
|  | else if(!set_io_base(devc, CONF_CDROM, pss_cdrom_port)) | 
|  | { | 
|  | printk(KERN_ERR "PSS: CDROM I/O port could not be set.\n"); | 
|  | } | 
|  | else					/* CDROM port successfully configured */ | 
|  | { | 
|  | printk(KERN_INFO "PSS: CDROM I/O port set to 0x%x.\n", pss_cdrom_port); | 
|  | } | 
|  | } | 
|  |  | 
|  | static int __init attach_pss(struct address_info *hw_config) | 
|  | { | 
|  | unsigned short  id; | 
|  | char tmp[100]; | 
|  |  | 
|  | devc->base = hw_config->io_base; | 
|  | devc->irq = hw_config->irq; | 
|  | devc->dma = hw_config->dma; | 
|  | devc->osp = hw_config->osp; | 
|  | devc->ad_mixer_dev = NO_WSS_MIXER; | 
|  |  | 
|  | if (!probe_pss(hw_config)) | 
|  | return 0; | 
|  |  | 
|  | id = inw(REG(PSS_ID)) & 0x00ff; | 
|  |  | 
|  | /* | 
|  | * Disable all emulations. Will be enabled later (if required). | 
|  | */ | 
|  |  | 
|  | disable_all_emulations(); | 
|  |  | 
|  | #ifdef YOU_REALLY_WANT_TO_ALLOCATE_THESE_RESOURCES | 
|  | if (sound_alloc_dma(hw_config->dma, "PSS")) | 
|  | { | 
|  | printk("pss.c: Can't allocate DMA channel.\n"); | 
|  | release_region(hw_config->io_base, 0x10); | 
|  | release_region(hw_config->io_base+0x10, 0x9); | 
|  | return 0; | 
|  | } | 
|  | if (!set_irq(devc, CONF_PSS, devc->irq)) | 
|  | { | 
|  | printk("PSS: IRQ allocation error.\n"); | 
|  | release_region(hw_config->io_base, 0x10); | 
|  | release_region(hw_config->io_base+0x10, 0x9); | 
|  | return 0; | 
|  | } | 
|  | if (!set_dma(devc, CONF_PSS, devc->dma)) | 
|  | { | 
|  | printk(KERN_ERR "PSS: DMA allocation error\n"); | 
|  | release_region(hw_config->io_base, 0x10); | 
|  | release_region(hw_config->io_base+0x10, 0x9); | 
|  | return 0; | 
|  | } | 
|  | #endif | 
|  |  | 
|  | configure_nonsound_components(); | 
|  | pss_initialized = 1; | 
|  | sprintf(tmp, "ECHO-PSS  Rev. %d", id); | 
|  | conf_printf(tmp, hw_config); | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | static int __init probe_pss_mpu(struct address_info *hw_config) | 
|  | { | 
|  | struct resource *ports; | 
|  | int timeout; | 
|  |  | 
|  | if (!pss_initialized) | 
|  | return 0; | 
|  |  | 
|  | ports = request_region(hw_config->io_base, 2, "mpu401"); | 
|  |  | 
|  | if (!ports) { | 
|  | printk(KERN_ERR "PSS: MPU I/O port conflict\n"); | 
|  | return 0; | 
|  | } | 
|  | if (!set_io_base(devc, CONF_MIDI, hw_config->io_base)) { | 
|  | printk(KERN_ERR "PSS: MIDI base could not be set.\n"); | 
|  | goto fail; | 
|  | } | 
|  | if (!set_irq(devc, CONF_MIDI, hw_config->irq)) { | 
|  | printk(KERN_ERR "PSS: MIDI IRQ allocation error.\n"); | 
|  | goto fail; | 
|  | } | 
|  | if (!pss_synthLen) { | 
|  | printk(KERN_ERR "PSS: Can't enable MPU. MIDI synth microcode not available.\n"); | 
|  | goto fail; | 
|  | } | 
|  | if (!pss_download_boot(devc, pss_synth, pss_synthLen, CPF_FIRST | CPF_LAST)) { | 
|  | printk(KERN_ERR "PSS: Unable to load MIDI synth microcode to DSP.\n"); | 
|  | goto fail; | 
|  | } | 
|  |  | 
|  | /* | 
|  | * Finally wait until the DSP algorithm has initialized itself and | 
|  | * deactivates receive interrupt. | 
|  | */ | 
|  |  | 
|  | for (timeout = 900000; timeout > 0; timeout--) | 
|  | { | 
|  | if ((inb(hw_config->io_base + 1) & 0x80) == 0)	/* Input data avail */ | 
|  | inb(hw_config->io_base);	/* Discard it */ | 
|  | else | 
|  | break;	/* No more input */ | 
|  | } | 
|  |  | 
|  | if (!probe_mpu401(hw_config, ports)) | 
|  | goto fail; | 
|  |  | 
|  | attach_mpu401(hw_config, THIS_MODULE);	/* Slot 1 */ | 
|  | if (hw_config->slots[1] != -1)	/* The MPU driver installed itself */ | 
|  | midi_devs[hw_config->slots[1]]->coproc = &pss_coproc_operations; | 
|  | return 1; | 
|  | fail: | 
|  | release_region(hw_config->io_base, 2); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pss_coproc_open(void *dev_info, int sub_device) | 
|  | { | 
|  | switch (sub_device) | 
|  | { | 
|  | case COPR_MIDI: | 
|  | if (pss_synthLen == 0) | 
|  | { | 
|  | printk(KERN_ERR "PSS: MIDI synth microcode not available.\n"); | 
|  | return -EIO; | 
|  | } | 
|  | if (nonstandard_microcode) | 
|  | if (!pss_download_boot(devc, pss_synth, pss_synthLen, CPF_FIRST | CPF_LAST)) | 
|  | { | 
|  | printk(KERN_ERR "PSS: Unable to load MIDI synth microcode to DSP.\n"); | 
|  | return -EIO; | 
|  | } | 
|  | nonstandard_microcode = 0; | 
|  | break; | 
|  |  | 
|  | default: | 
|  | break; | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void pss_coproc_close(void *dev_info, int sub_device) | 
|  | { | 
|  | return; | 
|  | } | 
|  |  | 
|  | static void pss_coproc_reset(void *dev_info) | 
|  | { | 
|  | if (pss_synthLen) | 
|  | if (!pss_download_boot(devc, pss_synth, pss_synthLen, CPF_FIRST | CPF_LAST)) | 
|  | { | 
|  | printk(KERN_ERR "PSS: Unable to load MIDI synth microcode to DSP.\n"); | 
|  | } | 
|  | nonstandard_microcode = 0; | 
|  | } | 
|  |  | 
|  | static int download_boot_block(void *dev_info, copr_buffer * buf) | 
|  | { | 
|  | if (buf->len <= 0 || buf->len > sizeof(buf->data)) | 
|  | return -EINVAL; | 
|  |  | 
|  | if (!pss_download_boot(devc, buf->data, buf->len, buf->flags)) | 
|  | { | 
|  | printk(KERN_ERR "PSS: Unable to load microcode block to DSP.\n"); | 
|  | return -EIO; | 
|  | } | 
|  | nonstandard_microcode = 1;	/* The MIDI microcode has been overwritten */ | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int pss_coproc_ioctl(void *dev_info, unsigned int cmd, void __user *arg, int local) | 
|  | { | 
|  | copr_buffer *buf; | 
|  | copr_msg *mbuf; | 
|  | copr_debug_buf dbuf; | 
|  | unsigned short tmp; | 
|  | unsigned long flags; | 
|  | unsigned short *data; | 
|  | int i, err; | 
|  | /* printk( "PSS coproc ioctl %x %x %d\n",  cmd,  arg,  local); */ | 
|  |  | 
|  | switch (cmd) | 
|  | { | 
|  | case SNDCTL_COPR_RESET: | 
|  | pss_coproc_reset(dev_info); | 
|  | return 0; | 
|  |  | 
|  | case SNDCTL_COPR_LOAD: | 
|  | buf = (copr_buffer *) vmalloc(sizeof(copr_buffer)); | 
|  | if (buf == NULL) | 
|  | return -ENOSPC; | 
|  | if (copy_from_user(buf, arg, sizeof(copr_buffer))) { | 
|  | vfree(buf); | 
|  | return -EFAULT; | 
|  | } | 
|  | err = download_boot_block(dev_info, buf); | 
|  | vfree(buf); | 
|  | return err; | 
|  |  | 
|  | case SNDCTL_COPR_SENDMSG: | 
|  | mbuf = (copr_msg *)vmalloc(sizeof(copr_msg)); | 
|  | if (mbuf == NULL) | 
|  | return -ENOSPC; | 
|  | if (copy_from_user(mbuf, arg, sizeof(copr_msg))) { | 
|  | vfree(mbuf); | 
|  | return -EFAULT; | 
|  | } | 
|  | data = (unsigned short *)(mbuf->data); | 
|  | spin_lock_irqsave(&lock, flags); | 
|  | for (i = 0; i < mbuf->len; i++) { | 
|  | if (!pss_put_dspword(devc, *data++)) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | mbuf->len = i;	/* feed back number of WORDs sent */ | 
|  | err = copy_to_user(arg, mbuf, sizeof(copr_msg)); | 
|  | vfree(mbuf); | 
|  | return err ? -EFAULT : -EIO; | 
|  | } | 
|  | } | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | vfree(mbuf); | 
|  | return 0; | 
|  |  | 
|  | case SNDCTL_COPR_RCVMSG: | 
|  | err = 0; | 
|  | mbuf = (copr_msg *)vmalloc(sizeof(copr_msg)); | 
|  | if (mbuf == NULL) | 
|  | return -ENOSPC; | 
|  | data = (unsigned short *)mbuf->data; | 
|  | spin_lock_irqsave(&lock, flags); | 
|  | for (i = 0; i < sizeof(mbuf->data)/sizeof(unsigned short); i++) { | 
|  | mbuf->len = i;	/* feed back number of WORDs read */ | 
|  | if (!pss_get_dspword(devc, data++)) { | 
|  | if (i == 0) | 
|  | err = -EIO; | 
|  | break; | 
|  | } | 
|  | } | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | if (copy_to_user(arg, mbuf, sizeof(copr_msg))) | 
|  | err = -EFAULT; | 
|  | vfree(mbuf); | 
|  | return err; | 
|  |  | 
|  | case SNDCTL_COPR_RDATA: | 
|  | if (copy_from_user(&dbuf, arg, sizeof(dbuf))) | 
|  | return -EFAULT; | 
|  | spin_lock_irqsave(&lock, flags); | 
|  | if (!pss_put_dspword(devc, 0x00d0)) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | if (!pss_put_dspword(devc, (unsigned short)(dbuf.parm1 & 0xffff))) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | if (!pss_get_dspword(devc, &tmp)) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | dbuf.parm1 = tmp; | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | if (copy_to_user(arg, &dbuf, sizeof(dbuf))) | 
|  | return -EFAULT; | 
|  | return 0; | 
|  |  | 
|  | case SNDCTL_COPR_WDATA: | 
|  | if (copy_from_user(&dbuf, arg, sizeof(dbuf))) | 
|  | return -EFAULT; | 
|  | spin_lock_irqsave(&lock, flags); | 
|  | if (!pss_put_dspword(devc, 0x00d1)) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | if (!pss_put_dspword(devc, (unsigned short) (dbuf.parm1 & 0xffff))) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | tmp = (unsigned int)dbuf.parm2 & 0xffff; | 
|  | if (!pss_put_dspword(devc, tmp)) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return 0; | 
|  |  | 
|  | case SNDCTL_COPR_WCODE: | 
|  | if (copy_from_user(&dbuf, arg, sizeof(dbuf))) | 
|  | return -EFAULT; | 
|  | spin_lock_irqsave(&lock, flags); | 
|  | if (!pss_put_dspword(devc, 0x00d3)) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | if (!pss_put_dspword(devc, (unsigned short)(dbuf.parm1 & 0xffff))) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | tmp = (unsigned int)dbuf.parm2 & 0x00ff; | 
|  | if (!pss_put_dspword(devc, tmp)) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | tmp = ((unsigned int)dbuf.parm2 >> 8) & 0xffff; | 
|  | if (!pss_put_dspword(devc, tmp)) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return 0; | 
|  |  | 
|  | case SNDCTL_COPR_RCODE: | 
|  | if (copy_from_user(&dbuf, arg, sizeof(dbuf))) | 
|  | return -EFAULT; | 
|  | spin_lock_irqsave(&lock, flags); | 
|  | if (!pss_put_dspword(devc, 0x00d2)) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | if (!pss_put_dspword(devc, (unsigned short)(dbuf.parm1 & 0xffff))) { | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | if (!pss_get_dspword(devc, &tmp)) { /* Read MSB */ | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | dbuf.parm1 = tmp << 8; | 
|  | if (!pss_get_dspword(devc, &tmp)) { /* Read LSB */ | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | return -EIO; | 
|  | } | 
|  | dbuf.parm1 |= tmp & 0x00ff; | 
|  | spin_unlock_irqrestore(&lock,flags); | 
|  | if (copy_to_user(arg, &dbuf, sizeof(dbuf))) | 
|  | return -EFAULT; | 
|  | return 0; | 
|  |  | 
|  | default: | 
|  | return -EINVAL; | 
|  | } | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | static coproc_operations pss_coproc_operations = | 
|  | { | 
|  | "ADSP-2115", | 
|  | THIS_MODULE, | 
|  | pss_coproc_open, | 
|  | pss_coproc_close, | 
|  | pss_coproc_ioctl, | 
|  | pss_coproc_reset, | 
|  | &pss_data | 
|  | }; | 
|  |  | 
|  | static int __init probe_pss_mss(struct address_info *hw_config) | 
|  | { | 
|  | volatile int timeout; | 
|  | struct resource *ports; | 
|  | int        my_mix = -999;	/* gcc shut up */ | 
|  |  | 
|  | if (!pss_initialized) | 
|  | return 0; | 
|  |  | 
|  | if (!request_region(hw_config->io_base, 4, "WSS config")) { | 
|  | printk(KERN_ERR "PSS: WSS I/O port conflicts.\n"); | 
|  | return 0; | 
|  | } | 
|  | ports = request_region(hw_config->io_base + 4, 4, "ad1848"); | 
|  | if (!ports) { | 
|  | printk(KERN_ERR "PSS: WSS I/O port conflicts.\n"); | 
|  | release_region(hw_config->io_base, 4); | 
|  | return 0; | 
|  | } | 
|  | if (!set_io_base(devc, CONF_WSS, hw_config->io_base)) { | 
|  | printk("PSS: WSS base not settable.\n"); | 
|  | goto fail; | 
|  | } | 
|  | if (!set_irq(devc, CONF_WSS, hw_config->irq)) { | 
|  | printk("PSS: WSS IRQ allocation error.\n"); | 
|  | goto fail; | 
|  | } | 
|  | if (!set_dma(devc, CONF_WSS, hw_config->dma)) { | 
|  | printk(KERN_ERR "PSS: WSS DMA allocation error\n"); | 
|  | goto fail; | 
|  | } | 
|  | /* | 
|  | * For some reason the card returns 0xff in the WSS status register | 
|  | * immediately after boot. Probably MIDI+SB emulation algorithm | 
|  | * downloaded to the ADSP2115 spends some time initializing the card. | 
|  | * Let's try to wait until it finishes this task. | 
|  | */ | 
|  | for (timeout = 0; timeout < 100000 && (inb(hw_config->io_base + WSS_INDEX) & | 
|  | WSS_INITIALIZING); timeout++) | 
|  | ; | 
|  |  | 
|  | outb((0x0b), hw_config->io_base + WSS_INDEX);	/* Required by some cards */ | 
|  |  | 
|  | for (timeout = 0; (inb(hw_config->io_base + WSS_DATA) & WSS_AUTOCALIBRATION) && | 
|  | (timeout < 100000); timeout++) | 
|  | ; | 
|  |  | 
|  | if (!probe_ms_sound(hw_config, ports)) | 
|  | goto fail; | 
|  |  | 
|  | devc->ad_mixer_dev = NO_WSS_MIXER; | 
|  | if (pss_mixer) | 
|  | { | 
|  | if ((my_mix = sound_install_mixer (MIXER_DRIVER_VERSION, | 
|  | "PSS-SPEAKERS and AD1848 (through MSS audio codec)", | 
|  | &pss_mixer_operations, | 
|  | sizeof (struct mixer_operations), | 
|  | devc)) < 0) | 
|  | { | 
|  | printk(KERN_ERR "Could not install PSS mixer\n"); | 
|  | goto fail; | 
|  | } | 
|  | } | 
|  | pss_mixer_reset(devc); | 
|  | attach_ms_sound(hw_config, ports, THIS_MODULE);	/* Slot 0 */ | 
|  |  | 
|  | if (hw_config->slots[0] != -1) | 
|  | { | 
|  | /* The MSS driver installed itself */ | 
|  | audio_devs[hw_config->slots[0]]->coproc = &pss_coproc_operations; | 
|  | if (pss_mixer && (num_mixers == (my_mix + 2))) | 
|  | { | 
|  | /* The MSS mixer installed */ | 
|  | devc->ad_mixer_dev = audio_devs[hw_config->slots[0]]->mixer_dev; | 
|  | } | 
|  | } | 
|  | return 1; | 
|  | fail: | 
|  | release_region(hw_config->io_base + 4, 4); | 
|  | release_region(hw_config->io_base, 4); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static inline void __exit unload_pss(struct address_info *hw_config) | 
|  | { | 
|  | release_region(hw_config->io_base, 0x10); | 
|  | release_region(hw_config->io_base+0x10, 0x9); | 
|  | } | 
|  |  | 
|  | static inline void __exit unload_pss_mpu(struct address_info *hw_config) | 
|  | { | 
|  | unload_mpu401(hw_config); | 
|  | } | 
|  |  | 
|  | static inline void __exit unload_pss_mss(struct address_info *hw_config) | 
|  | { | 
|  | unload_ms_sound(hw_config); | 
|  | } | 
|  |  | 
|  |  | 
|  | static struct address_info cfg; | 
|  | static struct address_info cfg2; | 
|  | static struct address_info cfg_mpu; | 
|  |  | 
|  | static int pss_io __initdata	= -1; | 
|  | static int mss_io __initdata	= -1; | 
|  | static int mss_irq __initdata	= -1; | 
|  | static int mss_dma __initdata	= -1; | 
|  | static int mpu_io __initdata	= -1; | 
|  | static int mpu_irq __initdata	= -1; | 
|  | static int pss_no_sound = 0;	/* Just configure non-sound components */ | 
|  | static int pss_keep_settings  = 1;	/* Keep hardware settings at module exit */ | 
|  | static char *pss_firmware = "/etc/sound/pss_synth"; | 
|  |  | 
|  | module_param(pss_io, int, 0); | 
|  | MODULE_PARM_DESC(pss_io, "Set i/o base of PSS card (probably 0x220 or 0x240)"); | 
|  | module_param(mss_io, int, 0); | 
|  | MODULE_PARM_DESC(mss_io, "Set WSS (audio) i/o base (0x530, 0x604, 0xE80, 0xF40, or other. Address must end in 0 or 4 and must be from 0x100 to 0xFF4)"); | 
|  | module_param(mss_irq, int, 0); | 
|  | MODULE_PARM_DESC(mss_irq, "Set WSS (audio) IRQ (3, 5, 7, 9, 10, 11, 12)"); | 
|  | module_param(mss_dma, int, 0); | 
|  | MODULE_PARM_DESC(mss_dma, "Set WSS (audio) DMA (0, 1, 3)"); | 
|  | module_param(mpu_io, int, 0); | 
|  | MODULE_PARM_DESC(mpu_io, "Set MIDI i/o base (0x330 or other. Address must be on 4 location boundaries and must be from 0x100 to 0xFFC)"); | 
|  | module_param(mpu_irq, int, 0); | 
|  | MODULE_PARM_DESC(mpu_irq, "Set MIDI IRQ (3, 5, 7, 9, 10, 11, 12)"); | 
|  | module_param(pss_cdrom_port, int, 0); | 
|  | MODULE_PARM_DESC(pss_cdrom_port, "Set the PSS CDROM port i/o base (0x340 or other)"); | 
|  | module_param(pss_enable_joystick, bool, 0); | 
|  | MODULE_PARM_DESC(pss_enable_joystick, "Enables the PSS joystick port (1 to enable, 0 to disable)"); | 
|  | module_param(pss_no_sound, bool, 0); | 
|  | MODULE_PARM_DESC(pss_no_sound, "Configure sound compoents (0 - no, 1 - yes)"); | 
|  | module_param(pss_keep_settings, bool, 0); | 
|  | MODULE_PARM_DESC(pss_keep_settings, "Keep hardware setting at driver unloading (0 - no, 1 - yes)"); | 
|  | module_param(pss_firmware, charp, 0); | 
|  | MODULE_PARM_DESC(pss_firmware, "Location of the firmware file (default - /etc/sound/pss_synth)"); | 
|  | module_param(pss_mixer, bool, 0); | 
|  | MODULE_PARM_DESC(pss_mixer, "Enable (1) or disable (0) PSS mixer (controlling of output volume, bass, treble, synth volume). The mixer is not available on all PSS cards."); | 
|  | MODULE_AUTHOR("Hannu Savolainen, Vladimir Michl"); | 
|  | MODULE_DESCRIPTION("Module for PSS sound cards (based on AD1848, ADSP-2115 and ESC614). This module includes control of output amplifier and synth volume of the Beethoven ADSP-16 card (this may work with other PSS cards)."); | 
|  | MODULE_LICENSE("GPL"); | 
|  |  | 
|  |  | 
|  | static int fw_load = 0; | 
|  | static int pssmpu = 0, pssmss = 0; | 
|  |  | 
|  | /* | 
|  | *    Load a PSS sound card module | 
|  | */ | 
|  |  | 
|  | static int __init init_pss(void) | 
|  | { | 
|  |  | 
|  | if(pss_no_sound)		/* If configuring only nonsound components */ | 
|  | { | 
|  | cfg.io_base = pss_io; | 
|  | if(!probe_pss(&cfg)) | 
|  | return -ENODEV; | 
|  | printk(KERN_INFO "ECHO-PSS  Rev. %d\n", inw(REG(PSS_ID)) & 0x00ff); | 
|  | printk(KERN_INFO "PSS: loading in no sound mode.\n"); | 
|  | disable_all_emulations(); | 
|  | configure_nonsound_components(); | 
|  | release_region(pss_io, 0x10); | 
|  | release_region(pss_io + 0x10, 0x9); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | cfg.io_base = pss_io; | 
|  |  | 
|  | cfg2.io_base = mss_io; | 
|  | cfg2.irq = mss_irq; | 
|  | cfg2.dma = mss_dma; | 
|  |  | 
|  | cfg_mpu.io_base = mpu_io; | 
|  | cfg_mpu.irq = mpu_irq; | 
|  |  | 
|  | if (cfg.io_base == -1 || cfg2.io_base == -1 || cfg2.irq == -1 || cfg.dma == -1) { | 
|  | printk(KERN_INFO "pss: mss_io, mss_dma, mss_irq and pss_io must be set.\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | if (!pss_synth) { | 
|  | fw_load = 1; | 
|  | pss_synthLen = mod_firmware_load(pss_firmware, (void *) &pss_synth); | 
|  | } | 
|  | if (!attach_pss(&cfg)) | 
|  | return -ENODEV; | 
|  | /* | 
|  | *    Attach stuff | 
|  | */ | 
|  | if (probe_pss_mpu(&cfg_mpu)) | 
|  | pssmpu = 1; | 
|  |  | 
|  | if (probe_pss_mss(&cfg2)) | 
|  | pssmss = 1; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void __exit cleanup_pss(void) | 
|  | { | 
|  | if(!pss_no_sound) | 
|  | { | 
|  | if(fw_load && pss_synth) | 
|  | vfree(pss_synth); | 
|  | if(pssmss) | 
|  | unload_pss_mss(&cfg2); | 
|  | if(pssmpu) | 
|  | unload_pss_mpu(&cfg_mpu); | 
|  | unload_pss(&cfg); | 
|  | } | 
|  |  | 
|  | if(!pss_keep_settings)	/* Keep hardware settings if asked */ | 
|  | { | 
|  | disable_all_emulations(); | 
|  | printk(KERN_INFO "Resetting PSS sound card configurations.\n"); | 
|  | } | 
|  | } | 
|  |  | 
|  | module_init(init_pss); | 
|  | module_exit(cleanup_pss); | 
|  |  | 
|  | #ifndef MODULE | 
|  | static int __init setup_pss(char *str) | 
|  | { | 
|  | /* io, mss_io, mss_irq, mss_dma, mpu_io, mpu_irq */ | 
|  | int ints[7]; | 
|  |  | 
|  | str = get_options(str, ARRAY_SIZE(ints), ints); | 
|  |  | 
|  | pss_io	= ints[1]; | 
|  | mss_io	= ints[2]; | 
|  | mss_irq	= ints[3]; | 
|  | mss_dma	= ints[4]; | 
|  | mpu_io	= ints[5]; | 
|  | mpu_irq	= ints[6]; | 
|  |  | 
|  | return 1; | 
|  | } | 
|  |  | 
|  | __setup("pss=", setup_pss); | 
|  | #endif |