blob: 2c38b642a8b8e8276f0adfabcae4c8109541a7c3 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Broadcom BCM470X / BCM5301X ARM platform code.
* DTS for D-Link DIR-885L
*
* Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com>
*/
/dts-v1/;
#include "bcm47094.dtsi"
#include "bcm5301x-nand-cs0-bch1.dtsi"
/ {
compatible = "dlink,dir-885l", "brcm,bcm47094", "brcm,bcm4708";
model = "D-Link DIR-885L";
chosen {
bootargs = "console=ttyS0,115200 earlycon";
};
memory@0 {
device_type = "memory";
reg = <0x00000000 0x08000000>,
<0x88000000 0x08000000>;
};
nand_controller: nand-controller@18028000 {
nand@0 {
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "firmware";
reg = <0x00000000 0x08000000>;
};
};
};
};
leds {
compatible = "gpio-leds";
power-white {
label = "bcm53xx:white:power";
gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "default-on";
};
wan-white {
label = "bcm53xx:white:wan";
gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
};
power-amber {
label = "bcm53xx:amber:power";
gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
};
wan-amber {
label = "bcm53xx:amber:wan";
gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
};
usb3-white {
label = "bcm53xx:white:usb3";
gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
trigger-sources = <&ohci_port1>, <&ehci_port1>,
<&xhci_port1>;
linux,default-trigger = "usbport";
};
2ghz {
label = "bcm53xx:white:2ghz";
gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
};
5ghz {
label = "bcm53xx:white:5ghz";
gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
};
};
gpio-keys {
compatible = "gpio-keys";
button-wps {
label = "WPS";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
};
/* Switch: router / extender */
button-extender {
label = "Extender";
linux,code = <BTN_0>;
gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
};
button-restart {
label = "Reset";
linux,code = <KEY_RESTART>;
gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
};
};
};
&usb3 {
vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
};
&spi_nor {
status = "okay";
};
&usb3_phy {
status = "okay";
};
&srab {
status = "okay";
ports {
port@0 {
reg = <0>;
label = "lan4";
};
port@1 {
reg = <1>;
label = "lan3";
};
port@2 {
reg = <2>;
label = "lan2";
};
port@3 {
reg = <3>;
label = "lan1";
};
port@4 {
reg = <4>;
label = "wan";
};
port@8 {
reg = <8>;
label = "cpu";
ethernet = <&gmac2>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};