blob: 9b9a18bbb20a9b943b95f4573f87637a3ca8a863 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,model-a-plus", "brcm,bcm2835";
model = "Raspberry Pi Model A+";
memory@0 {
device_type = "memory";
reg = <0 0x10000000>;
};
leds {
led-act {
gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
led-pwr {
label = "PWR";
gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
default-state = "keep";
linux,default-trigger = "default-on";
};
};
};
&gpio {
/*
* This is based on the unreleased schematic for the Model A+.
*
* Legend:
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "ID_SDA",
"ID_SCL",
"SDA1",
"SCL1",
"GPIO_GCLK",
"GPIO5",
"GPIO6",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"GPIO12",
"GPIO13",
/* Serial port */
"TXD0",
"RXD0",
"GPIO16",
"GPIO17",
"GPIO18",
"GPIO19",
"GPIO20",
"GPIO21",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"GPIO26",
"GPIO27",
"SDA0",
"SCL0",
"", /* GPIO30 */
"", /* GPIO31 */
"CAM_GPIO1", /* GPIO32 */
"", /* GPIO33 */
"", /* GPIO34 */
"PWR_LOW_N", /* GPIO35 */
"", /* GPIO36 */
"", /* GPIO37 */
"USB_LIMIT", /* GPIO38 */
"", /* GPIO39 */
"PWM0_OUT", /* GPIO40 */
"CAM_GPIO0", /* GPIO41 */
"", /* GPIO42 */
"", /* GPIO43 */
"", /* GPIO44 */
"PWM1_OUT", /* GPIO45 */
"HDMI_HPD_N",
"STATUS_LED",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
/* I2S interface */
i2s_alt0: i2s_alt0 {
brcm,pins = <18 19 20 21>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
};
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
status = "okay";
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
status = "okay";
};
&sdhost {
pinctrl-names = "default";
pinctrl-0 = <&sdhost_gpio48>;
bus-width = <4>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};