| /* |
| * PCA953x 4/8/16/24/40 bit I/O ports |
| * |
| * Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com> |
| * Copyright (C) 2007 Marvell International Ltd. |
| * |
| * Derived from drivers/i2c/chips/pca9539.c |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| */ |
| |
| #include <linux/acpi.h> |
| #include <linux/gpio/driver.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/i2c.h> |
| #include <linux/init.h> |
| #include <linux/interrupt.h> |
| #include <linux/module.h> |
| #include <linux/of_platform.h> |
| #include <linux/platform_data/pca953x.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/slab.h> |
| |
| #include <asm/unaligned.h> |
| |
| #define PCA953X_INPUT 0x00 |
| #define PCA953X_OUTPUT 0x01 |
| #define PCA953X_INVERT 0x02 |
| #define PCA953X_DIRECTION 0x03 |
| |
| #define REG_ADDR_AI 0x80 |
| |
| #define PCA957X_IN 0x00 |
| #define PCA957X_INVRT 0x01 |
| #define PCA957X_BKEN 0x02 |
| #define PCA957X_PUPD 0x03 |
| #define PCA957X_CFG 0x04 |
| #define PCA957X_OUT 0x05 |
| #define PCA957X_MSK 0x06 |
| #define PCA957X_INTS 0x07 |
| |
| #define PCAL953X_OUT_STRENGTH 0x20 |
| #define PCAL953X_IN_LATCH 0x22 |
| #define PCAL953X_PULL_EN 0x23 |
| #define PCAL953X_PULL_SEL 0x24 |
| #define PCAL953X_INT_MASK 0x25 |
| #define PCAL953X_INT_STAT 0x26 |
| #define PCAL953X_OUT_CONF 0x27 |
| |
| #define PCAL6524_INT_EDGE 0x28 |
| #define PCAL6524_INT_CLR 0x2a |
| #define PCAL6524_IN_STATUS 0x2b |
| #define PCAL6524_OUT_INDCONF 0x2c |
| #define PCAL6524_DEBOUNCE 0x2d |
| |
| #define PCA_GPIO_MASK 0x00FF |
| |
| #define PCAL_GPIO_MASK 0x1f |
| #define PCAL_PINCTRL_MASK 0xe0 |
| |
| #define PCA_INT 0x0100 |
| #define PCA_PCAL 0x0200 |
| #define PCA_LATCH_INT (PCA_PCAL | PCA_INT) |
| #define PCA953X_TYPE 0x1000 |
| #define PCA957X_TYPE 0x2000 |
| #define PCA_TYPE_MASK 0xF000 |
| |
| #define PCA_CHIP_TYPE(x) ((x) & PCA_TYPE_MASK) |
| |
| static const struct i2c_device_id pca953x_id[] = { |
| { "pca9505", 40 | PCA953X_TYPE | PCA_INT, }, |
| { "pca9534", 8 | PCA953X_TYPE | PCA_INT, }, |
| { "pca9535", 16 | PCA953X_TYPE | PCA_INT, }, |
| { "pca9536", 4 | PCA953X_TYPE, }, |
| { "pca9537", 4 | PCA953X_TYPE | PCA_INT, }, |
| { "pca9538", 8 | PCA953X_TYPE | PCA_INT, }, |
| { "pca9539", 16 | PCA953X_TYPE | PCA_INT, }, |
| { "pca9554", 8 | PCA953X_TYPE | PCA_INT, }, |
| { "pca9555", 16 | PCA953X_TYPE | PCA_INT, }, |
| { "pca9556", 8 | PCA953X_TYPE, }, |
| { "pca9557", 8 | PCA953X_TYPE, }, |
| { "pca9574", 8 | PCA957X_TYPE | PCA_INT, }, |
| { "pca9575", 16 | PCA957X_TYPE | PCA_INT, }, |
| { "pca9698", 40 | PCA953X_TYPE, }, |
| |
| { "pcal6524", 24 | PCA953X_TYPE | PCA_INT | PCA_PCAL, }, |
| { "pcal9555a", 16 | PCA953X_TYPE | PCA_INT | PCA_PCAL, }, |
| |
| { "max7310", 8 | PCA953X_TYPE, }, |
| { "max7312", 16 | PCA953X_TYPE | PCA_INT, }, |
| { "max7313", 16 | PCA953X_TYPE | PCA_INT, }, |
| { "max7315", 8 | PCA953X_TYPE | PCA_INT, }, |
| { "max7318", 16 | PCA953X_TYPE | PCA_INT, }, |
| { "pca6107", 8 | PCA953X_TYPE | PCA_INT, }, |
| { "tca6408", 8 | PCA953X_TYPE | PCA_INT, }, |
| { "tca6416", 16 | PCA953X_TYPE | PCA_INT, }, |
| { "tca6424", 24 | PCA953X_TYPE | PCA_INT, }, |
| { "tca9539", 16 | PCA953X_TYPE | PCA_INT, }, |
| { "tca9554", 8 | PCA953X_TYPE | PCA_INT, }, |
| { "xra1202", 8 | PCA953X_TYPE }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(i2c, pca953x_id); |
| |
| static const struct acpi_device_id pca953x_acpi_ids[] = { |
| { "INT3491", 16 | PCA953X_TYPE | PCA_INT | PCA_PCAL, }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(acpi, pca953x_acpi_ids); |
| |
| #define MAX_BANK 5 |
| #define BANK_SZ 8 |
| |
| #define NBANK(chip) DIV_ROUND_UP(chip->gpio_chip.ngpio, BANK_SZ) |
| |
| struct pca953x_reg_config { |
| int direction; |
| int output; |
| int input; |
| }; |
| |
| static const struct pca953x_reg_config pca953x_regs = { |
| .direction = PCA953X_DIRECTION, |
| .output = PCA953X_OUTPUT, |
| .input = PCA953X_INPUT, |
| }; |
| |
| static const struct pca953x_reg_config pca957x_regs = { |
| .direction = PCA957X_CFG, |
| .output = PCA957X_OUT, |
| .input = PCA957X_IN, |
| }; |
| |
| struct pca953x_chip { |
| unsigned gpio_start; |
| u8 reg_output[MAX_BANK]; |
| u8 reg_direction[MAX_BANK]; |
| struct mutex i2c_lock; |
| |
| #ifdef CONFIG_GPIO_PCA953X_IRQ |
| struct mutex irq_lock; |
| u8 irq_mask[MAX_BANK]; |
| u8 irq_stat[MAX_BANK]; |
| u8 irq_trig_raise[MAX_BANK]; |
| u8 irq_trig_fall[MAX_BANK]; |
| #endif |
| |
| struct i2c_client *client; |
| struct gpio_chip gpio_chip; |
| const char *const *names; |
| unsigned long driver_data; |
| struct regulator *regulator; |
| |
| const struct pca953x_reg_config *regs; |
| |
| int (*write_regs)(struct pca953x_chip *, int, u8 *); |
| int (*read_regs)(struct pca953x_chip *, int, u8 *); |
| }; |
| |
| static int pca953x_read_single(struct pca953x_chip *chip, int reg, u32 *val, |
| int off) |
| { |
| int ret; |
| int bank_shift = fls((chip->gpio_chip.ngpio - 1) / BANK_SZ); |
| int offset = off / BANK_SZ; |
| |
| ret = i2c_smbus_read_byte_data(chip->client, |
| (reg << bank_shift) + offset); |
| *val = ret; |
| |
| if (ret < 0) { |
| dev_err(&chip->client->dev, "failed reading register\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int pca953x_write_single(struct pca953x_chip *chip, int reg, u32 val, |
| int off) |
| { |
| int ret; |
| int bank_shift = fls((chip->gpio_chip.ngpio - 1) / BANK_SZ); |
| int offset = off / BANK_SZ; |
| |
| ret = i2c_smbus_write_byte_data(chip->client, |
| (reg << bank_shift) + offset, val); |
| |
| if (ret < 0) { |
| dev_err(&chip->client->dev, "failed writing register\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int pca953x_write_regs_8(struct pca953x_chip *chip, int reg, u8 *val) |
| { |
| return i2c_smbus_write_byte_data(chip->client, reg, *val); |
| } |
| |
| static int pca953x_write_regs_16(struct pca953x_chip *chip, int reg, u8 *val) |
| { |
| u16 word = get_unaligned((u16 *)val); |
| |
| return i2c_smbus_write_word_data(chip->client, reg << 1, word); |
| } |
| |
| static int pca957x_write_regs_16(struct pca953x_chip *chip, int reg, u8 *val) |
| { |
| int ret; |
| |
| ret = i2c_smbus_write_byte_data(chip->client, reg << 1, val[0]); |
| if (ret < 0) |
| return ret; |
| |
| return i2c_smbus_write_byte_data(chip->client, (reg << 1) + 1, val[1]); |
| } |
| |
| static int pca953x_write_regs_24(struct pca953x_chip *chip, int reg, u8 *val) |
| { |
| int bank_shift = fls((chip->gpio_chip.ngpio - 1) / BANK_SZ); |
| int addr = (reg & PCAL_GPIO_MASK) << bank_shift; |
| int pinctrl = (reg & PCAL_PINCTRL_MASK) << 1; |
| |
| return i2c_smbus_write_i2c_block_data(chip->client, |
| pinctrl | addr | REG_ADDR_AI, |
| NBANK(chip), val); |
| } |
| |
| static int pca953x_write_regs(struct pca953x_chip *chip, int reg, u8 *val) |
| { |
| int ret = 0; |
| |
| ret = chip->write_regs(chip, reg, val); |
| if (ret < 0) { |
| dev_err(&chip->client->dev, "failed writing register\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int pca953x_read_regs_8(struct pca953x_chip *chip, int reg, u8 *val) |
| { |
| int ret; |
| |
| ret = i2c_smbus_read_byte_data(chip->client, reg); |
| *val = ret; |
| |
| return ret; |
| } |
| |
| static int pca953x_read_regs_16(struct pca953x_chip *chip, int reg, u8 *val) |
| { |
| int ret; |
| |
| ret = i2c_smbus_read_word_data(chip->client, reg << 1); |
| put_unaligned(ret, (u16 *)val); |
| |
| return ret; |
| } |
| |
| static int pca953x_read_regs_24(struct pca953x_chip *chip, int reg, u8 *val) |
| { |
| int bank_shift = fls((chip->gpio_chip.ngpio - 1) / BANK_SZ); |
| int addr = (reg & PCAL_GPIO_MASK) << bank_shift; |
| int pinctrl = (reg & PCAL_PINCTRL_MASK) << 1; |
| |
| return i2c_smbus_read_i2c_block_data(chip->client, |
| pinctrl | addr | REG_ADDR_AI, |
| NBANK(chip), val); |
| } |
| |
| static int pca953x_read_regs(struct pca953x_chip *chip, int reg, u8 *val) |
| { |
| int ret; |
| |
| ret = chip->read_regs(chip, reg, val); |
| if (ret < 0) { |
| dev_err(&chip->client->dev, "failed reading register\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int pca953x_gpio_direction_input(struct gpio_chip *gc, unsigned off) |
| { |
| struct pca953x_chip *chip = gpiochip_get_data(gc); |
| u8 reg_val; |
| int ret; |
| |
| mutex_lock(&chip->i2c_lock); |
| reg_val = chip->reg_direction[off / BANK_SZ] | (1u << (off % BANK_SZ)); |
| |
| ret = pca953x_write_single(chip, chip->regs->direction, reg_val, off); |
| if (ret) |
| goto exit; |
| |
| chip->reg_direction[off / BANK_SZ] = reg_val; |
| exit: |
| mutex_unlock(&chip->i2c_lock); |
| return ret; |
| } |
| |
| static int pca953x_gpio_direction_output(struct gpio_chip *gc, |
| unsigned off, int val) |
| { |
| struct pca953x_chip *chip = gpiochip_get_data(gc); |
| u8 reg_val; |
| int ret; |
| |
| mutex_lock(&chip->i2c_lock); |
| /* set output level */ |
| if (val) |
| reg_val = chip->reg_output[off / BANK_SZ] |
| | (1u << (off % BANK_SZ)); |
| else |
| reg_val = chip->reg_output[off / BANK_SZ] |
| & ~(1u << (off % BANK_SZ)); |
| |
| ret = pca953x_write_single(chip, chip->regs->output, reg_val, off); |
| if (ret) |
| goto exit; |
| |
| chip->reg_output[off / BANK_SZ] = reg_val; |
| |
| /* then direction */ |
| reg_val = chip->reg_direction[off / BANK_SZ] & ~(1u << (off % BANK_SZ)); |
| ret = pca953x_write_single(chip, chip->regs->direction, reg_val, off); |
| if (ret) |
| goto exit; |
| |
| chip->reg_direction[off / BANK_SZ] = reg_val; |
| exit: |
| mutex_unlock(&chip->i2c_lock); |
| return ret; |
| } |
| |
| static int pca953x_gpio_get_value(struct gpio_chip *gc, unsigned off) |
| { |
| struct pca953x_chip *chip = gpiochip_get_data(gc); |
| u32 reg_val; |
| int ret; |
| |
| mutex_lock(&chip->i2c_lock); |
| ret = pca953x_read_single(chip, chip->regs->input, ®_val, off); |
| mutex_unlock(&chip->i2c_lock); |
| if (ret < 0) { |
| /* NOTE: diagnostic already emitted; that's all we should |
| * do unless gpio_*_value_cansleep() calls become different |
| * from their nonsleeping siblings (and report faults). |
| */ |
| return 0; |
| } |
| |
| return (reg_val & (1u << (off % BANK_SZ))) ? 1 : 0; |
| } |
| |
| static void pca953x_gpio_set_value(struct gpio_chip *gc, unsigned off, int val) |
| { |
| struct pca953x_chip *chip = gpiochip_get_data(gc); |
| u8 reg_val; |
| int ret; |
| |
| mutex_lock(&chip->i2c_lock); |
| if (val) |
| reg_val = chip->reg_output[off / BANK_SZ] |
| | (1u << (off % BANK_SZ)); |
| else |
| reg_val = chip->reg_output[off / BANK_SZ] |
| & ~(1u << (off % BANK_SZ)); |
| |
| ret = pca953x_write_single(chip, chip->regs->output, reg_val, off); |
| if (ret) |
| goto exit; |
| |
| chip->reg_output[off / BANK_SZ] = reg_val; |
| exit: |
| mutex_unlock(&chip->i2c_lock); |
| } |
| |
| static int pca953x_gpio_get_direction(struct gpio_chip *gc, unsigned off) |
| { |
| struct pca953x_chip *chip = gpiochip_get_data(gc); |
| u32 reg_val; |
| int ret; |
| |
| mutex_lock(&chip->i2c_lock); |
| ret = pca953x_read_single(chip, chip->regs->direction, ®_val, off); |
| mutex_unlock(&chip->i2c_lock); |
| if (ret < 0) |
| return ret; |
| |
| return !!(reg_val & (1u << (off % BANK_SZ))); |
| } |
| |
| static void pca953x_gpio_set_multiple(struct gpio_chip *gc, |
| unsigned long *mask, unsigned long *bits) |
| { |
| struct pca953x_chip *chip = gpiochip_get_data(gc); |
| unsigned int bank_mask, bank_val; |
| int bank_shift, bank; |
| u8 reg_val[MAX_BANK]; |
| int ret; |
| |
| bank_shift = fls((chip->gpio_chip.ngpio - 1) / BANK_SZ); |
| |
| mutex_lock(&chip->i2c_lock); |
| memcpy(reg_val, chip->reg_output, NBANK(chip)); |
| for (bank = 0; bank < NBANK(chip); bank++) { |
| bank_mask = mask[bank / sizeof(*mask)] >> |
| ((bank % sizeof(*mask)) * 8); |
| if (bank_mask) { |
| bank_val = bits[bank / sizeof(*bits)] >> |
| ((bank % sizeof(*bits)) * 8); |
| bank_val &= bank_mask; |
| reg_val[bank] = (reg_val[bank] & ~bank_mask) | bank_val; |
| } |
| } |
| |
| ret = i2c_smbus_write_i2c_block_data(chip->client, |
| chip->regs->output << bank_shift, |
| NBANK(chip), reg_val); |
| if (ret) |
| goto exit; |
| |
| memcpy(chip->reg_output, reg_val, NBANK(chip)); |
| exit: |
| mutex_unlock(&chip->i2c_lock); |
| } |
| |
| static void pca953x_setup_gpio(struct pca953x_chip *chip, int gpios) |
| { |
| struct gpio_chip *gc; |
| |
| gc = &chip->gpio_chip; |
| |
| gc->direction_input = pca953x_gpio_direction_input; |
| gc->direction_output = pca953x_gpio_direction_output; |
| gc->get = pca953x_gpio_get_value; |
| gc->set = pca953x_gpio_set_value; |
| gc->get_direction = pca953x_gpio_get_direction; |
| gc->set_multiple = pca953x_gpio_set_multiple; |
| gc->can_sleep = true; |
| |
| gc->base = chip->gpio_start; |
| gc->ngpio = gpios; |
| gc->label = chip->client->name; |
| gc->parent = &chip->client->dev; |
| gc->owner = THIS_MODULE; |
| gc->names = chip->names; |
| } |
| |
| #ifdef CONFIG_GPIO_PCA953X_IRQ |
| static void pca953x_irq_mask(struct irq_data *d) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct pca953x_chip *chip = gpiochip_get_data(gc); |
| |
| chip->irq_mask[d->hwirq / BANK_SZ] &= ~(1 << (d->hwirq % BANK_SZ)); |
| } |
| |
| static void pca953x_irq_unmask(struct irq_data *d) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct pca953x_chip *chip = gpiochip_get_data(gc); |
| |
| chip->irq_mask[d->hwirq / BANK_SZ] |= 1 << (d->hwirq % BANK_SZ); |
| } |
| |
| static void pca953x_irq_bus_lock(struct irq_data *d) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct pca953x_chip *chip = gpiochip_get_data(gc); |
| |
| mutex_lock(&chip->irq_lock); |
| } |
| |
| static void pca953x_irq_bus_sync_unlock(struct irq_data *d) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct pca953x_chip *chip = gpiochip_get_data(gc); |
| u8 new_irqs; |
| int level, i; |
| u8 invert_irq_mask[MAX_BANK]; |
| |
| if (chip->driver_data & PCA_PCAL) { |
| /* Enable latch on interrupt-enabled inputs */ |
| pca953x_write_regs(chip, PCAL953X_IN_LATCH, chip->irq_mask); |
| |
| for (i = 0; i < NBANK(chip); i++) |
| invert_irq_mask[i] = ~chip->irq_mask[i]; |
| |
| /* Unmask enabled interrupts */ |
| pca953x_write_regs(chip, PCAL953X_INT_MASK, invert_irq_mask); |
| } |
| |
| /* Look for any newly setup interrupt */ |
| for (i = 0; i < NBANK(chip); i++) { |
| new_irqs = chip->irq_trig_fall[i] | chip->irq_trig_raise[i]; |
| new_irqs &= ~chip->reg_direction[i]; |
| |
| while (new_irqs) { |
| level = __ffs(new_irqs); |
| pca953x_gpio_direction_input(&chip->gpio_chip, |
| level + (BANK_SZ * i)); |
| new_irqs &= ~(1 << level); |
| } |
| } |
| |
| mutex_unlock(&chip->irq_lock); |
| } |
| |
| static int pca953x_irq_set_type(struct irq_data *d, unsigned int type) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct pca953x_chip *chip = gpiochip_get_data(gc); |
| int bank_nb = d->hwirq / BANK_SZ; |
| u8 mask = 1 << (d->hwirq % BANK_SZ); |
| |
| if (!(type & IRQ_TYPE_EDGE_BOTH)) { |
| dev_err(&chip->client->dev, "irq %d: unsupported type %d\n", |
| d->irq, type); |
| return -EINVAL; |
| } |
| |
| if (type & IRQ_TYPE_EDGE_FALLING) |
| chip->irq_trig_fall[bank_nb] |= mask; |
| else |
| chip->irq_trig_fall[bank_nb] &= ~mask; |
| |
| if (type & IRQ_TYPE_EDGE_RISING) |
| chip->irq_trig_raise[bank_nb] |= mask; |
| else |
| chip->irq_trig_raise[bank_nb] &= ~mask; |
| |
| return 0; |
| } |
| |
| static void pca953x_irq_shutdown(struct irq_data *d) |
| { |
| struct pca953x_chip *chip = irq_data_get_irq_chip_data(d); |
| u8 mask = 1 << (d->hwirq % BANK_SZ); |
| |
| chip->irq_trig_raise[d->hwirq / BANK_SZ] &= ~mask; |
| chip->irq_trig_fall[d->hwirq / BANK_SZ] &= ~mask; |
| } |
| |
| static struct irq_chip pca953x_irq_chip = { |
| .name = "pca953x", |
| .irq_mask = pca953x_irq_mask, |
| .irq_unmask = pca953x_irq_unmask, |
| .irq_bus_lock = pca953x_irq_bus_lock, |
| .irq_bus_sync_unlock = pca953x_irq_bus_sync_unlock, |
| .irq_set_type = pca953x_irq_set_type, |
| .irq_shutdown = pca953x_irq_shutdown, |
| }; |
| |
| static bool pca953x_irq_pending(struct pca953x_chip *chip, u8 *pending) |
| { |
| u8 cur_stat[MAX_BANK]; |
| u8 old_stat[MAX_BANK]; |
| bool pending_seen = false; |
| bool trigger_seen = false; |
| u8 trigger[MAX_BANK]; |
| int ret, i; |
| |
| if (chip->driver_data & PCA_PCAL) { |
| /* Read the current interrupt status from the device */ |
| ret = pca953x_read_regs(chip, PCAL953X_INT_STAT, trigger); |
| if (ret) |
| return false; |
| |
| /* Check latched inputs and clear interrupt status */ |
| ret = pca953x_read_regs(chip, PCA953X_INPUT, cur_stat); |
| if (ret) |
| return false; |
| |
| for (i = 0; i < NBANK(chip); i++) { |
| /* Apply filter for rising/falling edge selection */ |
| pending[i] = (~cur_stat[i] & chip->irq_trig_fall[i]) | |
| (cur_stat[i] & chip->irq_trig_raise[i]); |
| pending[i] &= trigger[i]; |
| if (pending[i]) |
| pending_seen = true; |
| } |
| |
| return pending_seen; |
| } |
| |
| ret = pca953x_read_regs(chip, chip->regs->input, cur_stat); |
| if (ret) |
| return false; |
| |
| /* Remove output pins from the equation */ |
| for (i = 0; i < NBANK(chip); i++) |
| cur_stat[i] &= chip->reg_direction[i]; |
| |
| memcpy(old_stat, chip->irq_stat, NBANK(chip)); |
| |
| for (i = 0; i < NBANK(chip); i++) { |
| trigger[i] = (cur_stat[i] ^ old_stat[i]) & chip->irq_mask[i]; |
| if (trigger[i]) |
| trigger_seen = true; |
| } |
| |
| if (!trigger_seen) |
| return false; |
| |
| memcpy(chip->irq_stat, cur_stat, NBANK(chip)); |
| |
| for (i = 0; i < NBANK(chip); i++) { |
| pending[i] = (old_stat[i] & chip->irq_trig_fall[i]) | |
| (cur_stat[i] & chip->irq_trig_raise[i]); |
| pending[i] &= trigger[i]; |
| if (pending[i]) |
| pending_seen = true; |
| } |
| |
| return pending_seen; |
| } |
| |
| static irqreturn_t pca953x_irq_handler(int irq, void *devid) |
| { |
| struct pca953x_chip *chip = devid; |
| u8 pending[MAX_BANK]; |
| u8 level; |
| unsigned nhandled = 0; |
| int i; |
| |
| if (!pca953x_irq_pending(chip, pending)) |
| return IRQ_NONE; |
| |
| for (i = 0; i < NBANK(chip); i++) { |
| while (pending[i]) { |
| level = __ffs(pending[i]); |
| handle_nested_irq(irq_find_mapping(chip->gpio_chip.irq.domain, |
| level + (BANK_SZ * i))); |
| pending[i] &= ~(1 << level); |
| nhandled++; |
| } |
| } |
| |
| return (nhandled > 0) ? IRQ_HANDLED : IRQ_NONE; |
| } |
| |
| static int pca953x_irq_setup(struct pca953x_chip *chip, |
| int irq_base) |
| { |
| struct i2c_client *client = chip->client; |
| int ret, i; |
| |
| if (client->irq && irq_base != -1 |
| && (chip->driver_data & PCA_INT)) { |
| ret = pca953x_read_regs(chip, |
| chip->regs->input, chip->irq_stat); |
| if (ret) |
| return ret; |
| |
| /* |
| * There is no way to know which GPIO line generated the |
| * interrupt. We have to rely on the previous read for |
| * this purpose. |
| */ |
| for (i = 0; i < NBANK(chip); i++) |
| chip->irq_stat[i] &= chip->reg_direction[i]; |
| mutex_init(&chip->irq_lock); |
| |
| ret = devm_request_threaded_irq(&client->dev, |
| client->irq, |
| NULL, |
| pca953x_irq_handler, |
| IRQF_TRIGGER_LOW | IRQF_ONESHOT | |
| IRQF_SHARED, |
| dev_name(&client->dev), chip); |
| if (ret) { |
| dev_err(&client->dev, "failed to request irq %d\n", |
| client->irq); |
| return ret; |
| } |
| |
| ret = gpiochip_irqchip_add_nested(&chip->gpio_chip, |
| &pca953x_irq_chip, |
| irq_base, |
| handle_simple_irq, |
| IRQ_TYPE_NONE); |
| if (ret) { |
| dev_err(&client->dev, |
| "could not connect irqchip to gpiochip\n"); |
| return ret; |
| } |
| |
| gpiochip_set_nested_irqchip(&chip->gpio_chip, |
| &pca953x_irq_chip, |
| client->irq); |
| } |
| |
| return 0; |
| } |
| |
| #else /* CONFIG_GPIO_PCA953X_IRQ */ |
| static int pca953x_irq_setup(struct pca953x_chip *chip, |
| int irq_base) |
| { |
| struct i2c_client *client = chip->client; |
| |
| if (irq_base != -1 && (chip->driver_data & PCA_INT)) |
| dev_warn(&client->dev, "interrupt support not compiled in\n"); |
| |
| return 0; |
| } |
| #endif |
| |
| static int device_pca953x_init(struct pca953x_chip *chip, u32 invert) |
| { |
| int ret; |
| u8 val[MAX_BANK]; |
| |
| chip->regs = &pca953x_regs; |
| |
| ret = pca953x_read_regs(chip, chip->regs->output, chip->reg_output); |
| if (ret) |
| goto out; |
| |
| ret = pca953x_read_regs(chip, chip->regs->direction, |
| chip->reg_direction); |
| if (ret) |
| goto out; |
| |
| /* set platform specific polarity inversion */ |
| if (invert) |
| memset(val, 0xFF, NBANK(chip)); |
| else |
| memset(val, 0, NBANK(chip)); |
| |
| ret = pca953x_write_regs(chip, PCA953X_INVERT, val); |
| out: |
| return ret; |
| } |
| |
| static int device_pca957x_init(struct pca953x_chip *chip, u32 invert) |
| { |
| int ret; |
| u8 val[MAX_BANK]; |
| |
| chip->regs = &pca957x_regs; |
| |
| ret = pca953x_read_regs(chip, chip->regs->output, chip->reg_output); |
| if (ret) |
| goto out; |
| ret = pca953x_read_regs(chip, chip->regs->direction, |
| chip->reg_direction); |
| if (ret) |
| goto out; |
| |
| /* set platform specific polarity inversion */ |
| if (invert) |
| memset(val, 0xFF, NBANK(chip)); |
| else |
| memset(val, 0, NBANK(chip)); |
| ret = pca953x_write_regs(chip, PCA957X_INVRT, val); |
| if (ret) |
| goto out; |
| |
| /* To enable register 6, 7 to control pull up and pull down */ |
| memset(val, 0x02, NBANK(chip)); |
| ret = pca953x_write_regs(chip, PCA957X_BKEN, val); |
| if (ret) |
| goto out; |
| |
| return 0; |
| out: |
| return ret; |
| } |
| |
| static const struct of_device_id pca953x_dt_ids[]; |
| |
| static int pca953x_probe(struct i2c_client *client, |
| const struct i2c_device_id *i2c_id) |
| { |
| struct pca953x_platform_data *pdata; |
| struct pca953x_chip *chip; |
| int irq_base = 0; |
| int ret; |
| u32 invert = 0; |
| struct regulator *reg; |
| |
| chip = devm_kzalloc(&client->dev, |
| sizeof(struct pca953x_chip), GFP_KERNEL); |
| if (chip == NULL) |
| return -ENOMEM; |
| |
| pdata = dev_get_platdata(&client->dev); |
| if (pdata) { |
| irq_base = pdata->irq_base; |
| chip->gpio_start = pdata->gpio_base; |
| invert = pdata->invert; |
| chip->names = pdata->names; |
| } else { |
| struct gpio_desc *reset_gpio; |
| |
| chip->gpio_start = -1; |
| irq_base = 0; |
| |
| /* |
| * See if we need to de-assert a reset pin. |
| * |
| * There is no known ACPI-enabled platforms that are |
| * using "reset" GPIO. Otherwise any of those platform |
| * must use _DSD method with corresponding property. |
| */ |
| reset_gpio = devm_gpiod_get_optional(&client->dev, "reset", |
| GPIOD_OUT_LOW); |
| if (IS_ERR(reset_gpio)) |
| return PTR_ERR(reset_gpio); |
| } |
| |
| chip->client = client; |
| |
| reg = devm_regulator_get(&client->dev, "vcc"); |
| if (IS_ERR(reg)) { |
| ret = PTR_ERR(reg); |
| if (ret != -EPROBE_DEFER) |
| dev_err(&client->dev, "reg get err: %d\n", ret); |
| return ret; |
| } |
| ret = regulator_enable(reg); |
| if (ret) { |
| dev_err(&client->dev, "reg en err: %d\n", ret); |
| return ret; |
| } |
| chip->regulator = reg; |
| |
| if (i2c_id) { |
| chip->driver_data = i2c_id->driver_data; |
| } else { |
| const struct acpi_device_id *acpi_id; |
| struct device *dev = &client->dev; |
| |
| chip->driver_data = (uintptr_t)of_device_get_match_data(dev); |
| if (!chip->driver_data) { |
| acpi_id = acpi_match_device(pca953x_acpi_ids, dev); |
| if (!acpi_id) { |
| ret = -ENODEV; |
| goto err_exit; |
| } |
| |
| chip->driver_data = acpi_id->driver_data; |
| } |
| } |
| |
| mutex_init(&chip->i2c_lock); |
| /* |
| * In case we have an i2c-mux controlled by a GPIO provided by an |
| * expander using the same driver higher on the device tree, read the |
| * i2c adapter nesting depth and use the retrieved value as lockdep |
| * subclass for chip->i2c_lock. |
| * |
| * REVISIT: This solution is not complete. It protects us from lockdep |
| * false positives when the expander controlling the i2c-mux is on |
| * a different level on the device tree, but not when it's on the same |
| * level on a different branch (in which case the subclass number |
| * would be the same). |
| * |
| * TODO: Once a correct solution is developed, a similar fix should be |
| * applied to all other i2c-controlled GPIO expanders (and potentially |
| * regmap-i2c). |
| */ |
| lockdep_set_subclass(&chip->i2c_lock, |
| i2c_adapter_depth(client->adapter)); |
| |
| /* initialize cached registers from their original values. |
| * we can't share this chip with another i2c master. |
| */ |
| pca953x_setup_gpio(chip, chip->driver_data & PCA_GPIO_MASK); |
| |
| if (chip->gpio_chip.ngpio <= 8) { |
| chip->write_regs = pca953x_write_regs_8; |
| chip->read_regs = pca953x_read_regs_8; |
| } else if (chip->gpio_chip.ngpio >= 24) { |
| chip->write_regs = pca953x_write_regs_24; |
| chip->read_regs = pca953x_read_regs_24; |
| } else { |
| if (PCA_CHIP_TYPE(chip->driver_data) == PCA953X_TYPE) |
| chip->write_regs = pca953x_write_regs_16; |
| else |
| chip->write_regs = pca957x_write_regs_16; |
| chip->read_regs = pca953x_read_regs_16; |
| } |
| |
| if (PCA_CHIP_TYPE(chip->driver_data) == PCA953X_TYPE) |
| ret = device_pca953x_init(chip, invert); |
| else |
| ret = device_pca957x_init(chip, invert); |
| if (ret) |
| goto err_exit; |
| |
| ret = devm_gpiochip_add_data(&client->dev, &chip->gpio_chip, chip); |
| if (ret) |
| goto err_exit; |
| |
| ret = pca953x_irq_setup(chip, irq_base); |
| if (ret) |
| goto err_exit; |
| |
| if (pdata && pdata->setup) { |
| ret = pdata->setup(client, chip->gpio_chip.base, |
| chip->gpio_chip.ngpio, pdata->context); |
| if (ret < 0) |
| dev_warn(&client->dev, "setup failed, %d\n", ret); |
| } |
| |
| i2c_set_clientdata(client, chip); |
| return 0; |
| |
| err_exit: |
| regulator_disable(chip->regulator); |
| return ret; |
| } |
| |
| static int pca953x_remove(struct i2c_client *client) |
| { |
| struct pca953x_platform_data *pdata = dev_get_platdata(&client->dev); |
| struct pca953x_chip *chip = i2c_get_clientdata(client); |
| int ret; |
| |
| if (pdata && pdata->teardown) { |
| ret = pdata->teardown(client, chip->gpio_chip.base, |
| chip->gpio_chip.ngpio, pdata->context); |
| if (ret < 0) |
| dev_err(&client->dev, "%s failed, %d\n", |
| "teardown", ret); |
| } else { |
| ret = 0; |
| } |
| |
| regulator_disable(chip->regulator); |
| |
| return ret; |
| } |
| |
| /* convenience to stop overlong match-table lines */ |
| #define OF_953X(__nrgpio, __int) (void *)(__nrgpio | PCA953X_TYPE | __int) |
| #define OF_957X(__nrgpio, __int) (void *)(__nrgpio | PCA957X_TYPE | __int) |
| |
| static const struct of_device_id pca953x_dt_ids[] = { |
| { .compatible = "nxp,pca9505", .data = OF_953X(40, PCA_INT), }, |
| { .compatible = "nxp,pca9534", .data = OF_953X( 8, PCA_INT), }, |
| { .compatible = "nxp,pca9535", .data = OF_953X(16, PCA_INT), }, |
| { .compatible = "nxp,pca9536", .data = OF_953X( 4, 0), }, |
| { .compatible = "nxp,pca9537", .data = OF_953X( 4, PCA_INT), }, |
| { .compatible = "nxp,pca9538", .data = OF_953X( 8, PCA_INT), }, |
| { .compatible = "nxp,pca9539", .data = OF_953X(16, PCA_INT), }, |
| { .compatible = "nxp,pca9554", .data = OF_953X( 8, PCA_INT), }, |
| { .compatible = "nxp,pca9555", .data = OF_953X(16, PCA_INT), }, |
| { .compatible = "nxp,pca9556", .data = OF_953X( 8, 0), }, |
| { .compatible = "nxp,pca9557", .data = OF_953X( 8, 0), }, |
| { .compatible = "nxp,pca9574", .data = OF_957X( 8, PCA_INT), }, |
| { .compatible = "nxp,pca9575", .data = OF_957X(16, PCA_INT), }, |
| { .compatible = "nxp,pca9698", .data = OF_953X(40, 0), }, |
| |
| { .compatible = "nxp,pcal6524", .data = OF_953X(24, PCA_LATCH_INT), }, |
| { .compatible = "nxp,pcal9555a", .data = OF_953X(16, PCA_LATCH_INT), }, |
| |
| { .compatible = "maxim,max7310", .data = OF_953X( 8, 0), }, |
| { .compatible = "maxim,max7312", .data = OF_953X(16, PCA_INT), }, |
| { .compatible = "maxim,max7313", .data = OF_953X(16, PCA_INT), }, |
| { .compatible = "maxim,max7315", .data = OF_953X( 8, PCA_INT), }, |
| { .compatible = "maxim,max7318", .data = OF_953X(16, PCA_INT), }, |
| |
| { .compatible = "ti,pca6107", .data = OF_953X( 8, PCA_INT), }, |
| { .compatible = "ti,pca9536", .data = OF_953X( 4, 0), }, |
| { .compatible = "ti,tca6408", .data = OF_953X( 8, PCA_INT), }, |
| { .compatible = "ti,tca6416", .data = OF_953X(16, PCA_INT), }, |
| { .compatible = "ti,tca6424", .data = OF_953X(24, PCA_INT), }, |
| |
| { .compatible = "onnn,pca9654", .data = OF_953X( 8, PCA_INT), }, |
| |
| { .compatible = "exar,xra1202", .data = OF_953X( 8, 0), }, |
| { } |
| }; |
| |
| MODULE_DEVICE_TABLE(of, pca953x_dt_ids); |
| |
| static struct i2c_driver pca953x_driver = { |
| .driver = { |
| .name = "pca953x", |
| .of_match_table = pca953x_dt_ids, |
| .acpi_match_table = ACPI_PTR(pca953x_acpi_ids), |
| }, |
| .probe = pca953x_probe, |
| .remove = pca953x_remove, |
| .id_table = pca953x_id, |
| }; |
| |
| static int __init pca953x_init(void) |
| { |
| return i2c_add_driver(&pca953x_driver); |
| } |
| /* register after i2c postcore initcall and before |
| * subsys initcalls that may rely on these GPIOs |
| */ |
| subsys_initcall(pca953x_init); |
| |
| static void __exit pca953x_exit(void) |
| { |
| i2c_del_driver(&pca953x_driver); |
| } |
| module_exit(pca953x_exit); |
| |
| MODULE_AUTHOR("eric miao <eric.miao@marvell.com>"); |
| MODULE_DESCRIPTION("GPIO expander driver for PCA953x"); |
| MODULE_LICENSE("GPL"); |