| # SPDX-License-Identifier: GPL-2.0 |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/arm/cpus.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: ARM CPUs bindings |
| |
| maintainers: |
| - Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> |
| |
| description: |+ |
| The device tree allows to describe the layout of CPUs in a system through |
| the "cpus" node, which in turn contains a number of subnodes (ie "cpu") |
| defining properties for every cpu. |
| |
| Bindings for CPU nodes follow the Devicetree Specification, available from: |
| |
| https://www.devicetree.org/specifications/ |
| |
| with updates for 32-bit and 64-bit ARM systems provided in this document. |
| |
| ================================ |
| Convention used in this document |
| ================================ |
| |
| This document follows the conventions described in the Devicetree |
| Specification, with the addition: |
| |
| - square brackets define bitfields, eg reg[7:0] value of the bitfield in |
| the reg property contained in bits 7 down to 0 |
| |
| ===================================== |
| cpus and cpu node bindings definition |
| ===================================== |
| |
| The ARM architecture, in accordance with the Devicetree Specification, |
| requires the cpus and cpu nodes to be present and contain the properties |
| described below. |
| |
| properties: |
| reg: |
| maxItems: 1 |
| description: | |
| Usage and definition depend on ARM architecture version and |
| configuration: |
| |
| On uniprocessor ARM architectures previous to v7 |
| this property is required and must be set to 0. |
| |
| On ARM 11 MPcore based systems this property is |
| required and matches the CPUID[11:0] register bits. |
| |
| Bits [11:0] in the reg cell must be set to |
| bits [11:0] in CPU ID register. |
| |
| All other bits in the reg cell must be set to 0. |
| |
| On 32-bit ARM v7 or later systems this property is |
| required and matches the CPU MPIDR[23:0] register |
| bits. |
| |
| Bits [23:0] in the reg cell must be set to |
| bits [23:0] in MPIDR. |
| |
| All other bits in the reg cell must be set to 0. |
| |
| On ARM v8 64-bit systems this property is required |
| and matches the MPIDR_EL1 register affinity bits. |
| |
| * If cpus node's #address-cells property is set to 2 |
| |
| The first reg cell bits [7:0] must be set to |
| bits [39:32] of MPIDR_EL1. |
| |
| The second reg cell bits [23:0] must be set to |
| bits [23:0] of MPIDR_EL1. |
| |
| * If cpus node's #address-cells property is set to 1 |
| |
| The reg cell bits [23:0] must be set to bits [23:0] |
| of MPIDR_EL1. |
| |
| All other bits in the reg cells must be set to 0. |
| |
| compatible: |
| enum: |
| - arm,arm710t |
| - arm,arm720t |
| - arm,arm740t |
| - arm,arm7ej-s |
| - arm,arm7tdmi |
| - arm,arm7tdmi-s |
| - arm,arm9es |
| - arm,arm9ej-s |
| - arm,arm920t |
| - arm,arm922t |
| - arm,arm925 |
| - arm,arm926e-s |
| - arm,arm926ej-s |
| - arm,arm940t |
| - arm,arm946e-s |
| - arm,arm966e-s |
| - arm,arm968e-s |
| - arm,arm9tdmi |
| - arm,arm1020e |
| - arm,arm1020t |
| - arm,arm1022e |
| - arm,arm1026ej-s |
| - arm,arm1136j-s |
| - arm,arm1136jf-s |
| - arm,arm1156t2-s |
| - arm,arm1156t2f-s |
| - arm,arm1176jzf |
| - arm,arm1176jz-s |
| - arm,arm1176jzf-s |
| - arm,arm11mpcore |
| - arm,armv8 # Only for s/w models |
| - arm,cortex-a5 |
| - arm,cortex-a7 |
| - arm,cortex-a8 |
| - arm,cortex-a9 |
| - arm,cortex-a12 |
| - arm,cortex-a15 |
| - arm,cortex-a17 |
| - arm,cortex-a32 |
| - arm,cortex-a34 |
| - arm,cortex-a35 |
| - arm,cortex-a53 |
| - arm,cortex-a55 |
| - arm,cortex-a57 |
| - arm,cortex-a65 |
| - arm,cortex-a72 |
| - arm,cortex-a73 |
| - arm,cortex-a75 |
| - arm,cortex-a76 |
| - arm,cortex-a77 |
| - arm,cortex-m0 |
| - arm,cortex-m0+ |
| - arm,cortex-m1 |
| - arm,cortex-m3 |
| - arm,cortex-m4 |
| - arm,cortex-r4 |
| - arm,cortex-r5 |
| - arm,cortex-r7 |
| - arm,neoverse-e1 |
| - arm,neoverse-n1 |
| - brcm,brahma-b15 |
| - brcm,brahma-b53 |
| - brcm,vulcan |
| - cavium,thunder |
| - cavium,thunder2 |
| - faraday,fa526 |
| - intel,sa110 |
| - intel,sa1100 |
| - marvell,feroceon |
| - marvell,mohawk |
| - marvell,pj4a |
| - marvell,pj4b |
| - marvell,sheeva-v5 |
| - marvell,sheeva-v7 |
| - nvidia,tegra132-denver |
| - nvidia,tegra186-denver |
| - nvidia,tegra194-carmel |
| - qcom,krait |
| - qcom,kryo |
| - qcom,kryo385 |
| - qcom,kryo468 |
| - qcom,kryo485 |
| - qcom,scorpion |
| |
| enable-method: |
| allOf: |
| - $ref: '/schemas/types.yaml#/definitions/string' |
| - oneOf: |
| # On ARM v8 64-bit this property is required |
| - enum: |
| - psci |
| - spin-table |
| # On ARM 32-bit systems this property is optional |
| - enum: |
| - actions,s500-smp |
| - allwinner,sun6i-a31 |
| - allwinner,sun8i-a23 |
| - allwinner,sun9i-a80-smp |
| - allwinner,sun8i-a83t-smp |
| - amlogic,meson8-smp |
| - amlogic,meson8b-smp |
| - arm,realview-smp |
| - aspeed,ast2600-smp |
| - brcm,bcm11351-cpu-method |
| - brcm,bcm23550 |
| - brcm,bcm2836-smp |
| - brcm,bcm63138 |
| - brcm,bcm-nsp-smp |
| - brcm,brahma-b15 |
| - marvell,armada-375-smp |
| - marvell,armada-380-smp |
| - marvell,armada-390-smp |
| - marvell,armada-xp-smp |
| - marvell,98dx3236-smp |
| - mediatek,mt6589-smp |
| - mediatek,mt81xx-tz-smp |
| - qcom,gcc-msm8660 |
| - qcom,kpss-acc-v1 |
| - qcom,kpss-acc-v2 |
| - renesas,apmu |
| - renesas,r9a06g032-smp |
| - rockchip,rk3036-smp |
| - rockchip,rk3066-smp |
| - socionext,milbeaut-m10v-smp |
| - ste,dbx500-smp |
| |
| cpu-release-addr: |
| $ref: '/schemas/types.yaml#/definitions/uint64' |
| |
| description: |
| Required for systems that have an "enable-method" |
| property value of "spin-table". |
| On ARM v8 64-bit systems must be a two cell |
| property identifying a 64-bit zero-initialised |
| memory location. |
| |
| cpu-idle-states: |
| $ref: '/schemas/types.yaml#/definitions/phandle-array' |
| description: | |
| List of phandles to idle state nodes supported |
| by this cpu (see ./idle-states.txt). |
| |
| capacity-dmips-mhz: |
| $ref: '/schemas/types.yaml#/definitions/uint32' |
| description: |
| u32 value representing CPU capacity (see ./cpu-capacity.txt) in |
| DMIPS/MHz, relative to highest capacity-dmips-mhz |
| in the system. |
| |
| dynamic-power-coefficient: |
| $ref: '/schemas/types.yaml#/definitions/uint32' |
| description: |
| A u32 value that represents the running time dynamic |
| power coefficient in units of uW/MHz/V^2. The |
| coefficient can either be calculated from power |
| measurements or derived by analysis. |
| |
| The dynamic power consumption of the CPU is |
| proportional to the square of the Voltage (V) and |
| the clock frequency (f). The coefficient is used to |
| calculate the dynamic power as below - |
| |
| Pdyn = dynamic-power-coefficient * V^2 * f |
| |
| where voltage is in V, frequency is in MHz. |
| |
| power-domains: |
| $ref: '/schemas/types.yaml#/definitions/phandle-array' |
| description: |
| List of phandles and PM domain specifiers, as defined by bindings of the |
| PM domain provider (see also ../power_domain.txt). |
| |
| power-domain-names: |
| $ref: '/schemas/types.yaml#/definitions/string-array' |
| description: |
| A list of power domain name strings sorted in the same order as the |
| power-domains property. |
| |
| For PSCI based platforms, the name corresponding to the index of the PSCI |
| PM domain provider, must be "psci". |
| |
| qcom,saw: |
| $ref: '/schemas/types.yaml#/definitions/phandle' |
| description: | |
| Specifies the SAW* node associated with this CPU. |
| |
| Required for systems that have an "enable-method" property |
| value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2" |
| |
| * arm/msm/qcom,saw2.txt |
| |
| qcom,acc: |
| $ref: '/schemas/types.yaml#/definitions/phandle' |
| description: | |
| Specifies the ACC* node associated with this CPU. |
| |
| Required for systems that have an "enable-method" property |
| value of "qcom,kpss-acc-v1" or "qcom,kpss-acc-v2" |
| |
| * arm/msm/qcom,kpss-acc.txt |
| |
| rockchip,pmu: |
| $ref: '/schemas/types.yaml#/definitions/phandle' |
| description: | |
| Specifies the syscon node controlling the cpu core power domains. |
| |
| Optional for systems that have an "enable-method" |
| property value of "rockchip,rk3066-smp" |
| While optional, it is the preferred way to get access to |
| the cpu-core power-domains. |
| |
| required: |
| - device_type |
| - reg |
| - compatible |
| |
| dependencies: |
| rockchip,pmu: [enable-method] |
| |
| examples: |
| - | |
| cpus { |
| #size-cells = <0>; |
| #address-cells = <1>; |
| |
| cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a15"; |
| reg = <0x0>; |
| }; |
| |
| cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a15"; |
| reg = <0x1>; |
| }; |
| |
| cpu@100 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a7"; |
| reg = <0x100>; |
| }; |
| |
| cpu@101 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a7"; |
| reg = <0x101>; |
| }; |
| }; |
| |
| - | |
| // Example 2 (Cortex-A8 uniprocessor 32-bit system): |
| cpus { |
| #size-cells = <0>; |
| #address-cells = <1>; |
| |
| cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a8"; |
| reg = <0x0>; |
| }; |
| }; |
| |
| - | |
| // Example 3 (ARM 926EJ-S uniprocessor 32-bit system): |
| cpus { |
| #size-cells = <0>; |
| #address-cells = <1>; |
| |
| cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,arm926ej-s"; |
| reg = <0x0>; |
| }; |
| }; |
| |
| - | |
| // Example 4 (ARM Cortex-A57 64-bit system): |
| cpus { |
| #size-cells = <0>; |
| #address-cells = <2>; |
| |
| cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x0 0x0>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x0 0x1>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@100 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x0 0x100>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@101 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x0 0x101>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@10000 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x0 0x10000>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@10001 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x0 0x10001>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@10100 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x0 0x10100>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@10101 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x0 0x10101>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@100000000 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x1 0x0>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@100000001 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x1 0x1>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@100000100 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x1 0x100>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@100000101 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x1 0x101>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@100010000 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x1 0x10000>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@100010001 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x1 0x10001>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@100010100 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x1 0x10100>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| |
| cpu@100010101 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a57"; |
| reg = <0x1 0x10101>; |
| enable-method = "spin-table"; |
| cpu-release-addr = <0 0x20000000>; |
| }; |
| }; |
| ... |
