| /* | |
| * Driver for Microsemi VSC85xx PHYs | |
| * | |
| * Author: Nagaraju Lakkaraju | |
| * License: Dual MIT/GPL | |
| * Copyright (c) 2016 Microsemi Corporation | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/module.h> | |
| #include <linux/mdio.h> | |
| #include <linux/mii.h> | |
| #include <linux/phy.h> | |
| #include <linux/of.h> | |
| #include <linux/netdevice.h> | |
| #include <dt-bindings/net/mscc-phy-vsc8531.h> | |
| enum rgmii_rx_clock_delay { | |
| RGMII_RX_CLK_DELAY_0_2_NS = 0, | |
| RGMII_RX_CLK_DELAY_0_8_NS = 1, | |
| RGMII_RX_CLK_DELAY_1_1_NS = 2, | |
| RGMII_RX_CLK_DELAY_1_7_NS = 3, | |
| RGMII_RX_CLK_DELAY_2_0_NS = 4, | |
| RGMII_RX_CLK_DELAY_2_3_NS = 5, | |
| RGMII_RX_CLK_DELAY_2_6_NS = 6, | |
| RGMII_RX_CLK_DELAY_3_4_NS = 7 | |
| }; | |
| /* Microsemi VSC85xx PHY registers */ | |
| /* IEEE 802. Std Registers */ | |
| #define MSCC_PHY_BYPASS_CONTROL 18 | |
| #define DISABLE_HP_AUTO_MDIX_MASK 0x0080 | |
| #define DISABLE_PAIR_SWAP_CORR_MASK 0x0020 | |
| #define DISABLE_POLARITY_CORR_MASK 0x0010 | |
| #define MSCC_PHY_EXT_PHY_CNTL_1 23 | |
| #define MAC_IF_SELECTION_MASK 0x1800 | |
| #define MAC_IF_SELECTION_GMII 0 | |
| #define MAC_IF_SELECTION_RMII 1 | |
| #define MAC_IF_SELECTION_RGMII 2 | |
| #define MAC_IF_SELECTION_POS 11 | |
| #define FAR_END_LOOPBACK_MODE_MASK 0x0008 | |
| #define MII_VSC85XX_INT_MASK 25 | |
| #define MII_VSC85XX_INT_MASK_MASK 0xa000 | |
| #define MII_VSC85XX_INT_MASK_WOL 0x0040 | |
| #define MII_VSC85XX_INT_STATUS 26 | |
| #define MSCC_PHY_WOL_MAC_CONTROL 27 | |
| #define EDGE_RATE_CNTL_POS 5 | |
| #define EDGE_RATE_CNTL_MASK 0x00E0 | |
| #define MSCC_PHY_DEV_AUX_CNTL 28 | |
| #define HP_AUTO_MDIX_X_OVER_IND_MASK 0x2000 | |
| #define MSCC_PHY_LED_MODE_SEL 29 | |
| #define LED_1_MODE_SEL_MASK 0x00F0 | |
| #define LED_0_MODE_SEL_MASK 0x000F | |
| #define LED_1_MODE_SEL_POS 4 | |
| #define MSCC_EXT_PAGE_ACCESS 31 | |
| #define MSCC_PHY_PAGE_STANDARD 0x0000 /* Standard registers */ | |
| #define MSCC_PHY_PAGE_EXTENDED 0x0001 /* Extended registers */ | |
| #define MSCC_PHY_PAGE_EXTENDED_2 0x0002 /* Extended reg - page 2 */ | |
| /* Extended Page 1 Registers */ | |
| #define MSCC_PHY_EXT_MODE_CNTL 19 | |
| #define FORCE_MDI_CROSSOVER_MASK 0x000C | |
| #define FORCE_MDI_CROSSOVER_MDIX 0x000C | |
| #define FORCE_MDI_CROSSOVER_MDI 0x0008 | |
| #define MSCC_PHY_ACTIPHY_CNTL 20 | |
| #define DOWNSHIFT_CNTL_MASK 0x001C | |
| #define DOWNSHIFT_EN 0x0010 | |
| #define DOWNSHIFT_CNTL_POS 2 | |
| /* Extended Page 2 Registers */ | |
| #define MSCC_PHY_RGMII_CNTL 20 | |
| #define RGMII_RX_CLK_DELAY_MASK 0x0070 | |
| #define RGMII_RX_CLK_DELAY_POS 4 | |
| #define MSCC_PHY_WOL_LOWER_MAC_ADDR 21 | |
| #define MSCC_PHY_WOL_MID_MAC_ADDR 22 | |
| #define MSCC_PHY_WOL_UPPER_MAC_ADDR 23 | |
| #define MSCC_PHY_WOL_LOWER_PASSWD 24 | |
| #define MSCC_PHY_WOL_MID_PASSWD 25 | |
| #define MSCC_PHY_WOL_UPPER_PASSWD 26 | |
| #define MSCC_PHY_WOL_MAC_CONTROL 27 | |
| #define SECURE_ON_ENABLE 0x8000 | |
| #define SECURE_ON_PASSWD_LEN_4 0x4000 | |
| /* Microsemi PHY ID's */ | |
| #define PHY_ID_VSC8530 0x00070560 | |
| #define PHY_ID_VSC8531 0x00070570 | |
| #define PHY_ID_VSC8540 0x00070760 | |
| #define PHY_ID_VSC8541 0x00070770 | |
| #define MSCC_VDDMAC_1500 1500 | |
| #define MSCC_VDDMAC_1800 1800 | |
| #define MSCC_VDDMAC_2500 2500 | |
| #define MSCC_VDDMAC_3300 3300 | |
| #define DOWNSHIFT_COUNT_MAX 5 | |
| struct vsc8531_private { | |
| int rate_magic; | |
| u8 led_0_mode; | |
| u8 led_1_mode; | |
| }; | |
| #ifdef CONFIG_OF_MDIO | |
| struct vsc8531_edge_rate_table { | |
| u16 vddmac; | |
| u8 slowdown[8]; | |
| }; | |
| static const struct vsc8531_edge_rate_table edge_table[] = { | |
| {MSCC_VDDMAC_3300, { 0, 2, 4, 7, 10, 17, 29, 53} }, | |
| {MSCC_VDDMAC_2500, { 0, 3, 6, 10, 14, 23, 37, 63} }, | |
| {MSCC_VDDMAC_1800, { 0, 5, 9, 16, 23, 35, 52, 76} }, | |
| {MSCC_VDDMAC_1500, { 0, 6, 14, 21, 29, 42, 58, 77} }, | |
| }; | |
| #endif /* CONFIG_OF_MDIO */ | |
| static int vsc85xx_phy_page_set(struct phy_device *phydev, u8 page) | |
| { | |
| int rc; | |
| rc = phy_write(phydev, MSCC_EXT_PAGE_ACCESS, page); | |
| return rc; | |
| } | |
| static int vsc85xx_led_cntl_set(struct phy_device *phydev, | |
| u8 led_num, | |
| u8 mode) | |
| { | |
| int rc; | |
| u16 reg_val; | |
| mutex_lock(&phydev->lock); | |
| reg_val = phy_read(phydev, MSCC_PHY_LED_MODE_SEL); | |
| if (led_num) { | |
| reg_val &= ~LED_1_MODE_SEL_MASK; | |
| reg_val |= (((u16)mode << LED_1_MODE_SEL_POS) & | |
| LED_1_MODE_SEL_MASK); | |
| } else { | |
| reg_val &= ~LED_0_MODE_SEL_MASK; | |
| reg_val |= ((u16)mode & LED_0_MODE_SEL_MASK); | |
| } | |
| rc = phy_write(phydev, MSCC_PHY_LED_MODE_SEL, reg_val); | |
| mutex_unlock(&phydev->lock); | |
| return rc; | |
| } | |
| static int vsc85xx_mdix_get(struct phy_device *phydev, u8 *mdix) | |
| { | |
| u16 reg_val; | |
| reg_val = phy_read(phydev, MSCC_PHY_DEV_AUX_CNTL); | |
| if (reg_val & HP_AUTO_MDIX_X_OVER_IND_MASK) | |
| *mdix = ETH_TP_MDI_X; | |
| else | |
| *mdix = ETH_TP_MDI; | |
| return 0; | |
| } | |
| static int vsc85xx_mdix_set(struct phy_device *phydev, u8 mdix) | |
| { | |
| int rc; | |
| u16 reg_val; | |
| reg_val = phy_read(phydev, MSCC_PHY_BYPASS_CONTROL); | |
| if ((mdix == ETH_TP_MDI) || (mdix == ETH_TP_MDI_X)) { | |
| reg_val |= (DISABLE_PAIR_SWAP_CORR_MASK | | |
| DISABLE_POLARITY_CORR_MASK | | |
| DISABLE_HP_AUTO_MDIX_MASK); | |
| } else { | |
| reg_val &= ~(DISABLE_PAIR_SWAP_CORR_MASK | | |
| DISABLE_POLARITY_CORR_MASK | | |
| DISABLE_HP_AUTO_MDIX_MASK); | |
| } | |
| rc = phy_write(phydev, MSCC_PHY_BYPASS_CONTROL, reg_val); | |
| if (rc != 0) | |
| return rc; | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED); | |
| if (rc != 0) | |
| return rc; | |
| reg_val = phy_read(phydev, MSCC_PHY_EXT_MODE_CNTL); | |
| reg_val &= ~(FORCE_MDI_CROSSOVER_MASK); | |
| if (mdix == ETH_TP_MDI) | |
| reg_val |= FORCE_MDI_CROSSOVER_MDI; | |
| else if (mdix == ETH_TP_MDI_X) | |
| reg_val |= FORCE_MDI_CROSSOVER_MDIX; | |
| rc = phy_write(phydev, MSCC_PHY_EXT_MODE_CNTL, reg_val); | |
| if (rc != 0) | |
| return rc; | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | |
| if (rc != 0) | |
| return rc; | |
| return genphy_restart_aneg(phydev); | |
| } | |
| static int vsc85xx_downshift_get(struct phy_device *phydev, u8 *count) | |
| { | |
| int rc; | |
| u16 reg_val; | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED); | |
| if (rc != 0) | |
| goto out; | |
| reg_val = phy_read(phydev, MSCC_PHY_ACTIPHY_CNTL); | |
| reg_val &= DOWNSHIFT_CNTL_MASK; | |
| if (!(reg_val & DOWNSHIFT_EN)) | |
| *count = DOWNSHIFT_DEV_DISABLE; | |
| else | |
| *count = ((reg_val & ~DOWNSHIFT_EN) >> DOWNSHIFT_CNTL_POS) + 2; | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | |
| out: | |
| return rc; | |
| } | |
| static int vsc85xx_downshift_set(struct phy_device *phydev, u8 count) | |
| { | |
| int rc; | |
| u16 reg_val; | |
| if (count == DOWNSHIFT_DEV_DEFAULT_COUNT) { | |
| /* Default downshift count 3 (i.e. Bit3:2 = 0b01) */ | |
| count = ((1 << DOWNSHIFT_CNTL_POS) | DOWNSHIFT_EN); | |
| } else if (count > DOWNSHIFT_COUNT_MAX || count == 1) { | |
| phydev_err(phydev, "Downshift count should be 2,3,4 or 5\n"); | |
| return -ERANGE; | |
| } else if (count) { | |
| /* Downshift count is either 2,3,4 or 5 */ | |
| count = (((count - 2) << DOWNSHIFT_CNTL_POS) | DOWNSHIFT_EN); | |
| } | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED); | |
| if (rc != 0) | |
| goto out; | |
| reg_val = phy_read(phydev, MSCC_PHY_ACTIPHY_CNTL); | |
| reg_val &= ~(DOWNSHIFT_CNTL_MASK); | |
| reg_val |= count; | |
| rc = phy_write(phydev, MSCC_PHY_ACTIPHY_CNTL, reg_val); | |
| if (rc != 0) | |
| goto out; | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | |
| out: | |
| return rc; | |
| } | |
| static int vsc85xx_wol_set(struct phy_device *phydev, | |
| struct ethtool_wolinfo *wol) | |
| { | |
| int rc; | |
| u16 reg_val; | |
| u8 i; | |
| u16 pwd[3] = {0, 0, 0}; | |
| struct ethtool_wolinfo *wol_conf = wol; | |
| u8 *mac_addr = phydev->attached_dev->dev_addr; | |
| mutex_lock(&phydev->lock); | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED_2); | |
| if (rc != 0) | |
| goto out_unlock; | |
| if (wol->wolopts & WAKE_MAGIC) { | |
| /* Store the device address for the magic packet */ | |
| for (i = 0; i < ARRAY_SIZE(pwd); i++) | |
| pwd[i] = mac_addr[5 - (i * 2 + 1)] << 8 | | |
| mac_addr[5 - i * 2]; | |
| phy_write(phydev, MSCC_PHY_WOL_LOWER_MAC_ADDR, pwd[0]); | |
| phy_write(phydev, MSCC_PHY_WOL_MID_MAC_ADDR, pwd[1]); | |
| phy_write(phydev, MSCC_PHY_WOL_UPPER_MAC_ADDR, pwd[2]); | |
| } else { | |
| phy_write(phydev, MSCC_PHY_WOL_LOWER_MAC_ADDR, 0); | |
| phy_write(phydev, MSCC_PHY_WOL_MID_MAC_ADDR, 0); | |
| phy_write(phydev, MSCC_PHY_WOL_UPPER_MAC_ADDR, 0); | |
| } | |
| if (wol_conf->wolopts & WAKE_MAGICSECURE) { | |
| for (i = 0; i < ARRAY_SIZE(pwd); i++) | |
| pwd[i] = wol_conf->sopass[5 - (i * 2 + 1)] << 8 | | |
| wol_conf->sopass[5 - i * 2]; | |
| phy_write(phydev, MSCC_PHY_WOL_LOWER_PASSWD, pwd[0]); | |
| phy_write(phydev, MSCC_PHY_WOL_MID_PASSWD, pwd[1]); | |
| phy_write(phydev, MSCC_PHY_WOL_UPPER_PASSWD, pwd[2]); | |
| } else { | |
| phy_write(phydev, MSCC_PHY_WOL_LOWER_PASSWD, 0); | |
| phy_write(phydev, MSCC_PHY_WOL_MID_PASSWD, 0); | |
| phy_write(phydev, MSCC_PHY_WOL_UPPER_PASSWD, 0); | |
| } | |
| reg_val = phy_read(phydev, MSCC_PHY_WOL_MAC_CONTROL); | |
| if (wol_conf->wolopts & WAKE_MAGICSECURE) | |
| reg_val |= SECURE_ON_ENABLE; | |
| else | |
| reg_val &= ~SECURE_ON_ENABLE; | |
| phy_write(phydev, MSCC_PHY_WOL_MAC_CONTROL, reg_val); | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | |
| if (rc != 0) | |
| goto out_unlock; | |
| if (wol->wolopts & WAKE_MAGIC) { | |
| /* Enable the WOL interrupt */ | |
| reg_val = phy_read(phydev, MII_VSC85XX_INT_MASK); | |
| reg_val |= MII_VSC85XX_INT_MASK_WOL; | |
| rc = phy_write(phydev, MII_VSC85XX_INT_MASK, reg_val); | |
| if (rc != 0) | |
| goto out_unlock; | |
| } else { | |
| /* Disable the WOL interrupt */ | |
| reg_val = phy_read(phydev, MII_VSC85XX_INT_MASK); | |
| reg_val &= (~MII_VSC85XX_INT_MASK_WOL); | |
| rc = phy_write(phydev, MII_VSC85XX_INT_MASK, reg_val); | |
| if (rc != 0) | |
| goto out_unlock; | |
| } | |
| /* Clear WOL iterrupt status */ | |
| reg_val = phy_read(phydev, MII_VSC85XX_INT_STATUS); | |
| out_unlock: | |
| mutex_unlock(&phydev->lock); | |
| return rc; | |
| } | |
| static void vsc85xx_wol_get(struct phy_device *phydev, | |
| struct ethtool_wolinfo *wol) | |
| { | |
| int rc; | |
| u16 reg_val; | |
| u8 i; | |
| u16 pwd[3] = {0, 0, 0}; | |
| struct ethtool_wolinfo *wol_conf = wol; | |
| mutex_lock(&phydev->lock); | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED_2); | |
| if (rc != 0) | |
| goto out_unlock; | |
| reg_val = phy_read(phydev, MSCC_PHY_WOL_MAC_CONTROL); | |
| if (reg_val & SECURE_ON_ENABLE) | |
| wol_conf->wolopts |= WAKE_MAGICSECURE; | |
| if (wol_conf->wolopts & WAKE_MAGICSECURE) { | |
| pwd[0] = phy_read(phydev, MSCC_PHY_WOL_LOWER_PASSWD); | |
| pwd[1] = phy_read(phydev, MSCC_PHY_WOL_MID_PASSWD); | |
| pwd[2] = phy_read(phydev, MSCC_PHY_WOL_UPPER_PASSWD); | |
| for (i = 0; i < ARRAY_SIZE(pwd); i++) { | |
| wol_conf->sopass[5 - i * 2] = pwd[i] & 0x00ff; | |
| wol_conf->sopass[5 - (i * 2 + 1)] = (pwd[i] & 0xff00) | |
| >> 8; | |
| } | |
| } | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | |
| out_unlock: | |
| mutex_unlock(&phydev->lock); | |
| } | |
| #ifdef CONFIG_OF_MDIO | |
| static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev) | |
| { | |
| u8 sd; | |
| u16 vdd; | |
| int rc, i, j; | |
| struct device *dev = &phydev->mdio.dev; | |
| struct device_node *of_node = dev->of_node; | |
| u8 sd_array_size = ARRAY_SIZE(edge_table[0].slowdown); | |
| if (!of_node) | |
| return -ENODEV; | |
| rc = of_property_read_u16(of_node, "vsc8531,vddmac", &vdd); | |
| if (rc != 0) | |
| vdd = MSCC_VDDMAC_3300; | |
| rc = of_property_read_u8(of_node, "vsc8531,edge-slowdown", &sd); | |
| if (rc != 0) | |
| sd = 0; | |
| for (i = 0; i < ARRAY_SIZE(edge_table); i++) | |
| if (edge_table[i].vddmac == vdd) | |
| for (j = 0; j < sd_array_size; j++) | |
| if (edge_table[i].slowdown[j] == sd) | |
| return (sd_array_size - j - 1); | |
| return -EINVAL; | |
| } | |
| static int vsc85xx_dt_led_mode_get(struct phy_device *phydev, | |
| char *led, | |
| u8 default_mode) | |
| { | |
| struct device *dev = &phydev->mdio.dev; | |
| struct device_node *of_node = dev->of_node; | |
| u8 led_mode; | |
| int err; | |
| if (!of_node) | |
| return -ENODEV; | |
| led_mode = default_mode; | |
| err = of_property_read_u8(of_node, led, &led_mode); | |
| if (!err && (led_mode > 15 || led_mode == 7 || led_mode == 11)) { | |
| phydev_err(phydev, "DT %s invalid\n", led); | |
| return -EINVAL; | |
| } | |
| return led_mode; | |
| } | |
| #else | |
| static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev) | |
| { | |
| return 0; | |
| } | |
| static int vsc85xx_dt_led_mode_get(struct phy_device *phydev, | |
| char *led, | |
| u8 default_mode) | |
| { | |
| return default_mode; | |
| } | |
| #endif /* CONFIG_OF_MDIO */ | |
| static int vsc85xx_edge_rate_cntl_set(struct phy_device *phydev, u8 edge_rate) | |
| { | |
| int rc; | |
| u16 reg_val; | |
| mutex_lock(&phydev->lock); | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED_2); | |
| if (rc != 0) | |
| goto out_unlock; | |
| reg_val = phy_read(phydev, MSCC_PHY_WOL_MAC_CONTROL); | |
| reg_val &= ~(EDGE_RATE_CNTL_MASK); | |
| reg_val |= (edge_rate << EDGE_RATE_CNTL_POS); | |
| rc = phy_write(phydev, MSCC_PHY_WOL_MAC_CONTROL, reg_val); | |
| if (rc != 0) | |
| goto out_unlock; | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | |
| out_unlock: | |
| mutex_unlock(&phydev->lock); | |
| return rc; | |
| } | |
| static int vsc85xx_mac_if_set(struct phy_device *phydev, | |
| phy_interface_t interface) | |
| { | |
| int rc; | |
| u16 reg_val; | |
| mutex_lock(&phydev->lock); | |
| reg_val = phy_read(phydev, MSCC_PHY_EXT_PHY_CNTL_1); | |
| reg_val &= ~(MAC_IF_SELECTION_MASK); | |
| switch (interface) { | |
| case PHY_INTERFACE_MODE_RGMII: | |
| reg_val |= (MAC_IF_SELECTION_RGMII << MAC_IF_SELECTION_POS); | |
| break; | |
| case PHY_INTERFACE_MODE_RMII: | |
| reg_val |= (MAC_IF_SELECTION_RMII << MAC_IF_SELECTION_POS); | |
| break; | |
| case PHY_INTERFACE_MODE_MII: | |
| case PHY_INTERFACE_MODE_GMII: | |
| reg_val |= (MAC_IF_SELECTION_GMII << MAC_IF_SELECTION_POS); | |
| break; | |
| default: | |
| rc = -EINVAL; | |
| goto out_unlock; | |
| } | |
| rc = phy_write(phydev, MSCC_PHY_EXT_PHY_CNTL_1, reg_val); | |
| if (rc != 0) | |
| goto out_unlock; | |
| rc = genphy_soft_reset(phydev); | |
| out_unlock: | |
| mutex_unlock(&phydev->lock); | |
| return rc; | |
| } | |
| static int vsc85xx_default_config(struct phy_device *phydev) | |
| { | |
| int rc; | |
| u16 reg_val; | |
| phydev->mdix_ctrl = ETH_TP_MDI_AUTO; | |
| mutex_lock(&phydev->lock); | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_EXTENDED_2); | |
| if (rc != 0) | |
| goto out_unlock; | |
| reg_val = phy_read(phydev, MSCC_PHY_RGMII_CNTL); | |
| reg_val &= ~(RGMII_RX_CLK_DELAY_MASK); | |
| reg_val |= (RGMII_RX_CLK_DELAY_1_1_NS << RGMII_RX_CLK_DELAY_POS); | |
| phy_write(phydev, MSCC_PHY_RGMII_CNTL, reg_val); | |
| rc = vsc85xx_phy_page_set(phydev, MSCC_PHY_PAGE_STANDARD); | |
| out_unlock: | |
| mutex_unlock(&phydev->lock); | |
| return rc; | |
| } | |
| static int vsc85xx_get_tunable(struct phy_device *phydev, | |
| struct ethtool_tunable *tuna, void *data) | |
| { | |
| switch (tuna->id) { | |
| case ETHTOOL_PHY_DOWNSHIFT: | |
| return vsc85xx_downshift_get(phydev, (u8 *)data); | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| static int vsc85xx_set_tunable(struct phy_device *phydev, | |
| struct ethtool_tunable *tuna, | |
| const void *data) | |
| { | |
| switch (tuna->id) { | |
| case ETHTOOL_PHY_DOWNSHIFT: | |
| return vsc85xx_downshift_set(phydev, *(u8 *)data); | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| static int vsc85xx_config_init(struct phy_device *phydev) | |
| { | |
| int rc; | |
| struct vsc8531_private *vsc8531 = phydev->priv; | |
| rc = vsc85xx_default_config(phydev); | |
| if (rc) | |
| return rc; | |
| rc = vsc85xx_mac_if_set(phydev, phydev->interface); | |
| if (rc) | |
| return rc; | |
| rc = vsc85xx_edge_rate_cntl_set(phydev, vsc8531->rate_magic); | |
| if (rc) | |
| return rc; | |
| rc = vsc85xx_led_cntl_set(phydev, 1, vsc8531->led_1_mode); | |
| if (rc) | |
| return rc; | |
| rc = vsc85xx_led_cntl_set(phydev, 0, vsc8531->led_0_mode); | |
| if (rc) | |
| return rc; | |
| rc = genphy_config_init(phydev); | |
| return rc; | |
| } | |
| static int vsc85xx_ack_interrupt(struct phy_device *phydev) | |
| { | |
| int rc = 0; | |
| if (phydev->interrupts == PHY_INTERRUPT_ENABLED) | |
| rc = phy_read(phydev, MII_VSC85XX_INT_STATUS); | |
| return (rc < 0) ? rc : 0; | |
| } | |
| static int vsc85xx_config_intr(struct phy_device *phydev) | |
| { | |
| int rc; | |
| if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { | |
| rc = phy_write(phydev, MII_VSC85XX_INT_MASK, | |
| MII_VSC85XX_INT_MASK_MASK); | |
| } else { | |
| rc = phy_write(phydev, MII_VSC85XX_INT_MASK, 0); | |
| if (rc < 0) | |
| return rc; | |
| rc = phy_read(phydev, MII_VSC85XX_INT_STATUS); | |
| } | |
| return rc; | |
| } | |
| static int vsc85xx_config_aneg(struct phy_device *phydev) | |
| { | |
| int rc; | |
| rc = vsc85xx_mdix_set(phydev, phydev->mdix_ctrl); | |
| if (rc < 0) | |
| return rc; | |
| return genphy_config_aneg(phydev); | |
| } | |
| static int vsc85xx_read_status(struct phy_device *phydev) | |
| { | |
| int rc; | |
| rc = vsc85xx_mdix_get(phydev, &phydev->mdix); | |
| if (rc < 0) | |
| return rc; | |
| return genphy_read_status(phydev); | |
| } | |
| static int vsc85xx_probe(struct phy_device *phydev) | |
| { | |
| struct vsc8531_private *vsc8531; | |
| int rate_magic; | |
| int led_mode; | |
| rate_magic = vsc85xx_edge_rate_magic_get(phydev); | |
| if (rate_magic < 0) | |
| return rate_magic; | |
| vsc8531 = devm_kzalloc(&phydev->mdio.dev, sizeof(*vsc8531), GFP_KERNEL); | |
| if (!vsc8531) | |
| return -ENOMEM; | |
| phydev->priv = vsc8531; | |
| vsc8531->rate_magic = rate_magic; | |
| /* LED[0] and LED[1] mode */ | |
| led_mode = vsc85xx_dt_led_mode_get(phydev, "vsc8531,led-0-mode", | |
| VSC8531_LINK_1000_ACTIVITY); | |
| if (led_mode < 0) | |
| return led_mode; | |
| vsc8531->led_0_mode = led_mode; | |
| led_mode = vsc85xx_dt_led_mode_get(phydev, "vsc8531,led-1-mode", | |
| VSC8531_LINK_100_ACTIVITY); | |
| if (led_mode < 0) | |
| return led_mode; | |
| vsc8531->led_1_mode = led_mode; | |
| return 0; | |
| } | |
| /* Microsemi VSC85xx PHYs */ | |
| static struct phy_driver vsc85xx_driver[] = { | |
| { | |
| .phy_id = PHY_ID_VSC8530, | |
| .name = "Microsemi FE VSC8530", | |
| .phy_id_mask = 0xfffffff0, | |
| .features = PHY_BASIC_FEATURES, | |
| .flags = PHY_HAS_INTERRUPT, | |
| .soft_reset = &genphy_soft_reset, | |
| .config_init = &vsc85xx_config_init, | |
| .config_aneg = &vsc85xx_config_aneg, | |
| .aneg_done = &genphy_aneg_done, | |
| .read_status = &vsc85xx_read_status, | |
| .ack_interrupt = &vsc85xx_ack_interrupt, | |
| .config_intr = &vsc85xx_config_intr, | |
| .suspend = &genphy_suspend, | |
| .resume = &genphy_resume, | |
| .probe = &vsc85xx_probe, | |
| .set_wol = &vsc85xx_wol_set, | |
| .get_wol = &vsc85xx_wol_get, | |
| .get_tunable = &vsc85xx_get_tunable, | |
| .set_tunable = &vsc85xx_set_tunable, | |
| }, | |
| { | |
| .phy_id = PHY_ID_VSC8531, | |
| .name = "Microsemi VSC8531", | |
| .phy_id_mask = 0xfffffff0, | |
| .features = PHY_GBIT_FEATURES, | |
| .flags = PHY_HAS_INTERRUPT, | |
| .soft_reset = &genphy_soft_reset, | |
| .config_init = &vsc85xx_config_init, | |
| .config_aneg = &vsc85xx_config_aneg, | |
| .aneg_done = &genphy_aneg_done, | |
| .read_status = &vsc85xx_read_status, | |
| .ack_interrupt = &vsc85xx_ack_interrupt, | |
| .config_intr = &vsc85xx_config_intr, | |
| .suspend = &genphy_suspend, | |
| .resume = &genphy_resume, | |
| .probe = &vsc85xx_probe, | |
| .set_wol = &vsc85xx_wol_set, | |
| .get_wol = &vsc85xx_wol_get, | |
| .get_tunable = &vsc85xx_get_tunable, | |
| .set_tunable = &vsc85xx_set_tunable, | |
| }, | |
| { | |
| .phy_id = PHY_ID_VSC8540, | |
| .name = "Microsemi FE VSC8540 SyncE", | |
| .phy_id_mask = 0xfffffff0, | |
| .features = PHY_BASIC_FEATURES, | |
| .flags = PHY_HAS_INTERRUPT, | |
| .soft_reset = &genphy_soft_reset, | |
| .config_init = &vsc85xx_config_init, | |
| .config_aneg = &vsc85xx_config_aneg, | |
| .aneg_done = &genphy_aneg_done, | |
| .read_status = &vsc85xx_read_status, | |
| .ack_interrupt = &vsc85xx_ack_interrupt, | |
| .config_intr = &vsc85xx_config_intr, | |
| .suspend = &genphy_suspend, | |
| .resume = &genphy_resume, | |
| .probe = &vsc85xx_probe, | |
| .set_wol = &vsc85xx_wol_set, | |
| .get_wol = &vsc85xx_wol_get, | |
| .get_tunable = &vsc85xx_get_tunable, | |
| .set_tunable = &vsc85xx_set_tunable, | |
| }, | |
| { | |
| .phy_id = PHY_ID_VSC8541, | |
| .name = "Microsemi VSC8541 SyncE", | |
| .phy_id_mask = 0xfffffff0, | |
| .features = PHY_GBIT_FEATURES, | |
| .flags = PHY_HAS_INTERRUPT, | |
| .soft_reset = &genphy_soft_reset, | |
| .config_init = &vsc85xx_config_init, | |
| .config_aneg = &vsc85xx_config_aneg, | |
| .aneg_done = &genphy_aneg_done, | |
| .read_status = &vsc85xx_read_status, | |
| .ack_interrupt = &vsc85xx_ack_interrupt, | |
| .config_intr = &vsc85xx_config_intr, | |
| .suspend = &genphy_suspend, | |
| .resume = &genphy_resume, | |
| .probe = &vsc85xx_probe, | |
| .set_wol = &vsc85xx_wol_set, | |
| .get_wol = &vsc85xx_wol_get, | |
| .get_tunable = &vsc85xx_get_tunable, | |
| .set_tunable = &vsc85xx_set_tunable, | |
| } | |
| }; | |
| module_phy_driver(vsc85xx_driver); | |
| static struct mdio_device_id __maybe_unused vsc85xx_tbl[] = { | |
| { PHY_ID_VSC8530, 0xfffffff0, }, | |
| { PHY_ID_VSC8531, 0xfffffff0, }, | |
| { PHY_ID_VSC8540, 0xfffffff0, }, | |
| { PHY_ID_VSC8541, 0xfffffff0, }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(mdio, vsc85xx_tbl); | |
| MODULE_DESCRIPTION("Microsemi VSC85xx PHY driver"); | |
| MODULE_AUTHOR("Nagaraju Lakkaraju"); | |
| MODULE_LICENSE("Dual MIT/GPL"); |