Documentation/devicetree/bindings/usb/dwc3.txt

synopsys DWC3 CORE

DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
      as described in 'usb/generic.txt'

Required properties:
 - compatible: must be "snps,dwc3"
 - reg : Address and length of the register set for the device
 - interrupts: Interrupts used by the dwc3 controller.
 - clock-names: should contain "ref", "bus_early", "suspend"
 - clocks: list of phandle and clock specifier pairs corresponding to
           entries in the clock-names property.

Exception for clocks:
  clocks are optional if the parent node (i.e. glue-layer) is compatible to
  one of the following:
    "amlogic,meson-axg-dwc3"
    "amlogic,meson-gxl-dwc3"
    "cavium,octeon-7130-usb-uctl"
    "qcom,dwc3"
    "samsung,exynos5250-dwusb3"
    "samsung,exynos7-dwusb3"
    "sprd,sc9860-dwc3"
    "st,stih407-dwc3"
    "ti,am437x-dwc3"
    "ti,dwc3"
    "ti,keystone-dwc3"
    "rockchip,rk3399-dwc3"
    "xlnx,zynqmp-dwc3"

Optional properties:
 - usb-phy : array of phandle for the PHY device.  The first element
   in the array is expected to be a handle to the USB2/HS PHY and
   the second element is expected to be a handle to the USB3/SS PHY
 - phys: from the *Generic PHY* bindings
 - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy"
	or "usb3-phy".
 - resets: a single pair of phandle and reset specifier
 - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
 - snps,disable_scramble_quirk: true when SW should disable data scrambling.
	Only really useful for FPGA builds.
 - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled
 - snps,lpm-nyet-threshold: LPM NYET threshold
 - snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk
 - snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
 - snps,req_p1p2p3_quirk: when set, the core will always request for
			P1/P2/P3 transition sequence.
 - snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain
			amount of 8B10B errors occur.
 - snps,del_phy_power_chg_quirk: when set core will delay PHY power change
			from P0 to P1/P2/P3.
 - snps,lfps_filter_quirk: when set core will filter LFPS reception.
 - snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start
			Polling LFPS after RX.Detect.
 - snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value.
 - snps,tx_de_emphasis: the value driven to the PHY is controlled by the
			LTSSM during USB3 Compliance mode.
 - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
 - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
 - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
			disabling the suspend signal to the PHY.
 - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection
			in PHY P3 power state.
 - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists
			in GUSB2PHYCFG, specify that USB2 PHY doesn't provide
			a free-running PHY clock.
 - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power
			from P0 to P1/P2/P3 without delay.
 - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check
			during HS transmit.
 - snps,dis_metastability_quirk: when set, disable metastability workaround.
			CAUTION: use only if you are absolutely sure of it.
 - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
			utmi_l1_suspend_n, false when asserts utmi_sleep_n
 - snps,hird-threshold: HIRD threshold
 - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
   UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
 - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
	register for post-silicon frame length adjustment when the
	fladj_30mhz_sdbnd signal is invalid or incorrect.
 - snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode
			only. Set this and rx-max-burst-prd to a valid,
			non-zero value 1-16 (DWC_usb31 programming guide
			section 1.2.4) to enable periodic ESS RX threshold.
 - snps,rx-max-burst-prd: max periodic ESS RX burst size - host mode only. Set
			this and rx-thr-num-pkt-prd to a valid, non-zero value
			1-16 (DWC_usb31 programming guide section 1.2.4) to
			enable periodic ESS RX threshold.
 - snps,tx-thr-num-pkt-prd: periodic ESS TX packet threshold count - host mode
			only. Set this and tx-max-burst-prd to a valid,
			non-zero value 1-16 (DWC_usb31 programming guide
			section 1.2.3) to enable periodic ESS TX threshold.
 - snps,tx-max-burst-prd: max periodic ESS TX burst size - host mode only. Set
			this and tx-thr-num-pkt-prd to a valid, non-zero value
			1-16 (DWC_usb31 programming guide section 1.2.3) to
			enable periodic ESS TX threshold.

 - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.

 - in addition all properties from usb-xhci.txt from the current directory are
   supported as well


This is usually a subnode to DWC3 glue to which it is connected.

dwc3@4a030000 {
	compatible = "snps,dwc3";
	reg = <0x4a030000 0xcfff>;
	interrupts = <0 92 4>
	usb-phy = <&usb2_phy>, <&usb3,phy>;
};