| /* |
| * linux/drivers/acorn/net/ether1.c |
| * |
| * Copyright (C) 1996-2000 Russell King |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| * Acorn ether1 driver (82586 chip) for Acorn machines |
| * |
| * We basically keep two queues in the cards memory - one for transmit |
| * and one for receive. Each has a head and a tail. The head is where |
| * we/the chip adds packets to be transmitted/received, and the tail |
| * is where the transmitter has got to/where the receiver will stop. |
| * Both of these queues are circular, and since the chip is running |
| * all the time, we have to be careful when we modify the pointers etc |
| * so that the buffer memory contents is valid all the time. |
| * |
| * Change log: |
| * 1.00 RMK Released |
| * 1.01 RMK 19/03/1996 Transfers the last odd byte onto/off of the card now. |
| * 1.02 RMK 25/05/1997 Added code to restart RU if it goes not ready |
| * 1.03 RMK 14/09/1997 Cleaned up the handling of a reset during the TX interrupt. |
| * Should prevent lockup. |
| * 1.04 RMK 17/09/1997 Added more info when initialsation of chip goes wrong. |
| * TDR now only reports failure when chip reports non-zero |
| * TDR time-distance. |
| * 1.05 RMK 31/12/1997 Removed calls to dev_tint for 2.1 |
| * 1.06 RMK 10/02/2000 Updated for 2.3.43 |
| * 1.07 RMK 13/05/2000 Updated for 2.3.99-pre8 |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/kernel.h> |
| #include <linux/types.h> |
| #include <linux/fcntl.h> |
| #include <linux/interrupt.h> |
| #include <linux/ioport.h> |
| #include <linux/in.h> |
| #include <linux/slab.h> |
| #include <linux/string.h> |
| #include <linux/errno.h> |
| #include <linux/device.h> |
| #include <linux/init.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/skbuff.h> |
| #include <linux/bitops.h> |
| |
| #include <asm/io.h> |
| #include <asm/dma.h> |
| #include <asm/ecard.h> |
| |
| #define __ETHER1_C |
| #include "ether1.h" |
| |
| static unsigned int net_debug = NET_DEBUG; |
| |
| #define BUFFER_SIZE 0x10000 |
| #define TX_AREA_START 0x00100 |
| #define TX_AREA_END 0x05000 |
| #define RX_AREA_START 0x05000 |
| #define RX_AREA_END 0x0fc00 |
| |
| static int ether1_open(struct net_device *dev); |
| static int ether1_sendpacket(struct sk_buff *skb, struct net_device *dev); |
| static irqreturn_t ether1_interrupt(int irq, void *dev_id); |
| static int ether1_close(struct net_device *dev); |
| static void ether1_setmulticastlist(struct net_device *dev); |
| static void ether1_timeout(struct net_device *dev); |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| static char version[] = "ether1 ethernet driver (c) 2000 Russell King v1.07\n"; |
| |
| #define BUS_16 16 |
| #define BUS_8 8 |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| #define DISABLEIRQS 1 |
| #define NORMALIRQS 0 |
| |
| #define ether1_readw(dev, addr, type, offset, svflgs) ether1_inw_p (dev, addr + (int)(&((type *)0)->offset), svflgs) |
| #define ether1_writew(dev, val, addr, type, offset, svflgs) ether1_outw_p (dev, val, addr + (int)(&((type *)0)->offset), svflgs) |
| |
| static inline unsigned short |
| ether1_inw_p (struct net_device *dev, int addr, int svflgs) |
| { |
| unsigned long flags; |
| unsigned short ret; |
| |
| if (svflgs) |
| local_irq_save (flags); |
| |
| writeb(addr >> 12, REG_PAGE); |
| ret = readw(ETHER1_RAM + ((addr & 4095) << 1)); |
| if (svflgs) |
| local_irq_restore (flags); |
| return ret; |
| } |
| |
| static inline void |
| ether1_outw_p (struct net_device *dev, unsigned short val, int addr, int svflgs) |
| { |
| unsigned long flags; |
| |
| if (svflgs) |
| local_irq_save (flags); |
| |
| writeb(addr >> 12, REG_PAGE); |
| writew(val, ETHER1_RAM + ((addr & 4095) << 1)); |
| if (svflgs) |
| local_irq_restore (flags); |
| } |
| |
| /* |
| * Some inline assembler to allow fast transfers on to/off of the card. |
| * Since this driver depends on some features presented by the ARM |
| * specific architecture, and that you can't configure this driver |
| * without specifiing ARM mode, this is not a problem. |
| * |
| * This routine is essentially an optimised memcpy from the card's |
| * onboard RAM to kernel memory. |
| */ |
| static void |
| ether1_writebuffer (struct net_device *dev, void *data, unsigned int start, unsigned int length) |
| { |
| unsigned int page, thislen, offset; |
| void __iomem *addr; |
| |
| offset = start & 4095; |
| page = start >> 12; |
| addr = ETHER1_RAM + (offset << 1); |
| |
| if (offset + length > 4096) |
| thislen = 4096 - offset; |
| else |
| thislen = length; |
| |
| do { |
| int used; |
| |
| writeb(page, REG_PAGE); |
| length -= thislen; |
| |
| __asm__ __volatile__( |
| "subs %3, %3, #2\n\ |
| bmi 2f\n\ |
| 1: ldr %0, [%1], #2\n\ |
| mov %0, %0, lsl #16\n\ |
| orr %0, %0, %0, lsr #16\n\ |
| str %0, [%2], #4\n\ |
| subs %3, %3, #2\n\ |
| bmi 2f\n\ |
| ldr %0, [%1], #2\n\ |
| mov %0, %0, lsl #16\n\ |
| orr %0, %0, %0, lsr #16\n\ |
| str %0, [%2], #4\n\ |
| subs %3, %3, #2\n\ |
| bmi 2f\n\ |
| ldr %0, [%1], #2\n\ |
| mov %0, %0, lsl #16\n\ |
| orr %0, %0, %0, lsr #16\n\ |
| str %0, [%2], #4\n\ |
| subs %3, %3, #2\n\ |
| bmi 2f\n\ |
| ldr %0, [%1], #2\n\ |
| mov %0, %0, lsl #16\n\ |
| orr %0, %0, %0, lsr #16\n\ |
| str %0, [%2], #4\n\ |
| subs %3, %3, #2\n\ |
| bpl 1b\n\ |
| 2: adds %3, %3, #1\n\ |
| ldreqb %0, [%1]\n\ |
| streqb %0, [%2]" |
| : "=&r" (used), "=&r" (data) |
| : "r" (addr), "r" (thislen), "1" (data)); |
| |
| addr = ETHER1_RAM; |
| |
| thislen = length; |
| if (thislen > 4096) |
| thislen = 4096; |
| page++; |
| } while (thislen); |
| } |
| |
| static void |
| ether1_readbuffer (struct net_device *dev, void *data, unsigned int start, unsigned int length) |
| { |
| unsigned int page, thislen, offset; |
| void __iomem *addr; |
| |
| offset = start & 4095; |
| page = start >> 12; |
| addr = ETHER1_RAM + (offset << 1); |
| |
| if (offset + length > 4096) |
| thislen = 4096 - offset; |
| else |
| thislen = length; |
| |
| do { |
| int used; |
| |
| writeb(page, REG_PAGE); |
| length -= thislen; |
| |
| __asm__ __volatile__( |
| "subs %3, %3, #2\n\ |
| bmi 2f\n\ |
| 1: ldr %0, [%2], #4\n\ |
| strb %0, [%1], #1\n\ |
| mov %0, %0, lsr #8\n\ |
| strb %0, [%1], #1\n\ |
| subs %3, %3, #2\n\ |
| bmi 2f\n\ |
| ldr %0, [%2], #4\n\ |
| strb %0, [%1], #1\n\ |
| mov %0, %0, lsr #8\n\ |
| strb %0, [%1], #1\n\ |
| subs %3, %3, #2\n\ |
| bmi 2f\n\ |
| ldr %0, [%2], #4\n\ |
| strb %0, [%1], #1\n\ |
| mov %0, %0, lsr #8\n\ |
| strb %0, [%1], #1\n\ |
| subs %3, %3, #2\n\ |
| bmi 2f\n\ |
| ldr %0, [%2], #4\n\ |
| strb %0, [%1], #1\n\ |
| mov %0, %0, lsr #8\n\ |
| strb %0, [%1], #1\n\ |
| subs %3, %3, #2\n\ |
| bpl 1b\n\ |
| 2: adds %3, %3, #1\n\ |
| ldreqb %0, [%2]\n\ |
| streqb %0, [%1]" |
| : "=&r" (used), "=&r" (data) |
| : "r" (addr), "r" (thislen), "1" (data)); |
| |
| addr = ETHER1_RAM; |
| |
| thislen = length; |
| if (thislen > 4096) |
| thislen = 4096; |
| page++; |
| } while (thislen); |
| } |
| |
| static int |
| ether1_ramtest(struct net_device *dev, unsigned char byte) |
| { |
| unsigned char *buffer = kmalloc (BUFFER_SIZE, GFP_KERNEL); |
| int i, ret = BUFFER_SIZE; |
| int max_errors = 15; |
| int bad = -1; |
| int bad_start = 0; |
| |
| if (!buffer) |
| return 1; |
| |
| memset (buffer, byte, BUFFER_SIZE); |
| ether1_writebuffer (dev, buffer, 0, BUFFER_SIZE); |
| memset (buffer, byte ^ 0xff, BUFFER_SIZE); |
| ether1_readbuffer (dev, buffer, 0, BUFFER_SIZE); |
| |
| for (i = 0; i < BUFFER_SIZE; i++) { |
| if (buffer[i] != byte) { |
| if (max_errors >= 0 && bad != buffer[i]) { |
| if (bad != -1) |
| printk ("\n"); |
| printk (KERN_CRIT "%s: RAM failed with (%02X instead of %02X) at 0x%04X", |
| dev->name, buffer[i], byte, i); |
| ret = -ENODEV; |
| max_errors --; |
| bad = buffer[i]; |
| bad_start = i; |
| } |
| } else { |
| if (bad != -1) { |
| if (bad_start == i - 1) |
| printk ("\n"); |
| else |
| printk (" - 0x%04X\n", i - 1); |
| bad = -1; |
| } |
| } |
| } |
| |
| if (bad != -1) |
| printk (" - 0x%04X\n", BUFFER_SIZE); |
| kfree (buffer); |
| |
| return ret; |
| } |
| |
| static int |
| ether1_reset (struct net_device *dev) |
| { |
| writeb(CTRL_RST|CTRL_ACK, REG_CONTROL); |
| return BUS_16; |
| } |
| |
| static int |
| ether1_init_2(struct net_device *dev) |
| { |
| int i; |
| dev->mem_start = 0; |
| |
| i = ether1_ramtest (dev, 0x5a); |
| |
| if (i > 0) |
| i = ether1_ramtest (dev, 0x1e); |
| |
| if (i <= 0) |
| return -ENODEV; |
| |
| dev->mem_end = i; |
| return 0; |
| } |
| |
| /* |
| * These are the structures that are loaded into the ether RAM card to |
| * initialise the 82586 |
| */ |
| |
| /* at 0x0100 */ |
| #define NOP_ADDR (TX_AREA_START) |
| #define NOP_SIZE (0x06) |
| static nop_t init_nop = { |
| 0, |
| CMD_NOP, |
| NOP_ADDR |
| }; |
| |
| /* at 0x003a */ |
| #define TDR_ADDR (0x003a) |
| #define TDR_SIZE (0x08) |
| static tdr_t init_tdr = { |
| 0, |
| CMD_TDR | CMD_INTR, |
| NOP_ADDR, |
| 0 |
| }; |
| |
| /* at 0x002e */ |
| #define MC_ADDR (0x002e) |
| #define MC_SIZE (0x0c) |
| static mc_t init_mc = { |
| 0, |
| CMD_SETMULTICAST, |
| TDR_ADDR, |
| 0, |
| { { 0, } } |
| }; |
| |
| /* at 0x0022 */ |
| #define SA_ADDR (0x0022) |
| #define SA_SIZE (0x0c) |
| static sa_t init_sa = { |
| 0, |
| CMD_SETADDRESS, |
| MC_ADDR, |
| { 0, } |
| }; |
| |
| /* at 0x0010 */ |
| #define CFG_ADDR (0x0010) |
| #define CFG_SIZE (0x12) |
| static cfg_t init_cfg = { |
| 0, |
| CMD_CONFIG, |
| SA_ADDR, |
| 8, |
| 8, |
| CFG8_SRDY, |
| CFG9_PREAMB8 | CFG9_ADDRLENBUF | CFG9_ADDRLEN(6), |
| 0, |
| 0x60, |
| 0, |
| CFG13_RETRY(15) | CFG13_SLOTH(2), |
| 0, |
| }; |
| |
| /* at 0x0000 */ |
| #define SCB_ADDR (0x0000) |
| #define SCB_SIZE (0x10) |
| static scb_t init_scb = { |
| 0, |
| SCB_CMDACKRNR | SCB_CMDACKCNA | SCB_CMDACKFR | SCB_CMDACKCX, |
| CFG_ADDR, |
| RX_AREA_START, |
| 0, |
| 0, |
| 0, |
| 0 |
| }; |
| |
| /* at 0xffee */ |
| #define ISCP_ADDR (0xffee) |
| #define ISCP_SIZE (0x08) |
| static iscp_t init_iscp = { |
| 1, |
| SCB_ADDR, |
| 0x0000, |
| 0x0000 |
| }; |
| |
| /* at 0xfff6 */ |
| #define SCP_ADDR (0xfff6) |
| #define SCP_SIZE (0x0a) |
| static scp_t init_scp = { |
| SCP_SY_16BBUS, |
| { 0, 0 }, |
| ISCP_ADDR, |
| 0 |
| }; |
| |
| #define RFD_SIZE (0x16) |
| static rfd_t init_rfd = { |
| 0, |
| 0, |
| 0, |
| 0, |
| { 0, }, |
| { 0, }, |
| 0 |
| }; |
| |
| #define RBD_SIZE (0x0a) |
| static rbd_t init_rbd = { |
| 0, |
| 0, |
| 0, |
| 0, |
| ETH_FRAME_LEN + 8 |
| }; |
| |
| #define TX_SIZE (0x08) |
| #define TBD_SIZE (0x08) |
| |
| static int |
| ether1_init_for_open (struct net_device *dev) |
| { |
| int i, status, addr, next, next2; |
| int failures = 0; |
| unsigned long timeout; |
| |
| writeb(CTRL_RST|CTRL_ACK, REG_CONTROL); |
| |
| for (i = 0; i < 6; i++) |
| init_sa.sa_addr[i] = dev->dev_addr[i]; |
| |
| /* load data structures into ether1 RAM */ |
| ether1_writebuffer (dev, &init_scp, SCP_ADDR, SCP_SIZE); |
| ether1_writebuffer (dev, &init_iscp, ISCP_ADDR, ISCP_SIZE); |
| ether1_writebuffer (dev, &init_scb, SCB_ADDR, SCB_SIZE); |
| ether1_writebuffer (dev, &init_cfg, CFG_ADDR, CFG_SIZE); |
| ether1_writebuffer (dev, &init_sa, SA_ADDR, SA_SIZE); |
| ether1_writebuffer (dev, &init_mc, MC_ADDR, MC_SIZE); |
| ether1_writebuffer (dev, &init_tdr, TDR_ADDR, TDR_SIZE); |
| ether1_writebuffer (dev, &init_nop, NOP_ADDR, NOP_SIZE); |
| |
| if (ether1_readw(dev, CFG_ADDR, cfg_t, cfg_command, NORMALIRQS) != CMD_CONFIG) { |
| printk (KERN_ERR "%s: detected either RAM fault or compiler bug\n", |
| dev->name); |
| return 1; |
| } |
| |
| /* |
| * setup circularly linked list of { rfd, rbd, buffer }, with |
| * all rfds circularly linked, rbds circularly linked. |
| * First rfd is linked to scp, first rbd is linked to first |
| * rfd. Last rbd has a suspend command. |
| */ |
| addr = RX_AREA_START; |
| do { |
| next = addr + RFD_SIZE + RBD_SIZE + ETH_FRAME_LEN + 10; |
| next2 = next + RFD_SIZE + RBD_SIZE + ETH_FRAME_LEN + 10; |
| |
| if (next2 >= RX_AREA_END) { |
| next = RX_AREA_START; |
| init_rfd.rfd_command = RFD_CMDEL | RFD_CMDSUSPEND; |
| priv(dev)->rx_tail = addr; |
| } else |
| init_rfd.rfd_command = 0; |
| if (addr == RX_AREA_START) |
| init_rfd.rfd_rbdoffset = addr + RFD_SIZE; |
| else |
| init_rfd.rfd_rbdoffset = 0; |
| init_rfd.rfd_link = next; |
| init_rbd.rbd_link = next + RFD_SIZE; |
| init_rbd.rbd_bufl = addr + RFD_SIZE + RBD_SIZE; |
| |
| ether1_writebuffer (dev, &init_rfd, addr, RFD_SIZE); |
| ether1_writebuffer (dev, &init_rbd, addr + RFD_SIZE, RBD_SIZE); |
| addr = next; |
| } while (next2 < RX_AREA_END); |
| |
| priv(dev)->tx_link = NOP_ADDR; |
| priv(dev)->tx_head = NOP_ADDR + NOP_SIZE; |
| priv(dev)->tx_tail = TDR_ADDR; |
| priv(dev)->rx_head = RX_AREA_START; |
| |
| /* release reset & give 586 a prod */ |
| priv(dev)->resetting = 1; |
| priv(dev)->initialising = 1; |
| writeb(CTRL_RST, REG_CONTROL); |
| writeb(0, REG_CONTROL); |
| writeb(CTRL_CA, REG_CONTROL); |
| |
| /* 586 should now unset iscp.busy */ |
| timeout = jiffies + HZ/2; |
| while (ether1_readw(dev, ISCP_ADDR, iscp_t, iscp_busy, DISABLEIRQS) == 1) { |
| if (time_after(jiffies, timeout)) { |
| printk (KERN_WARNING "%s: can't initialise 82586: iscp is busy\n", dev->name); |
| return 1; |
| } |
| } |
| |
| /* check status of commands that we issued */ |
| timeout += HZ/10; |
| while (((status = ether1_readw(dev, CFG_ADDR, cfg_t, cfg_status, DISABLEIRQS)) |
| & STAT_COMPLETE) == 0) { |
| if (time_after(jiffies, timeout)) |
| break; |
| } |
| |
| if ((status & (STAT_COMPLETE | STAT_OK)) != (STAT_COMPLETE | STAT_OK)) { |
| printk (KERN_WARNING "%s: can't initialise 82586: config status %04X\n", dev->name, status); |
| printk (KERN_DEBUG "%s: SCB=[STS=%04X CMD=%04X CBL=%04X RFA=%04X]\n", dev->name, |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_command, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_rfa_offset, NORMALIRQS)); |
| failures += 1; |
| } |
| |
| timeout += HZ/10; |
| while (((status = ether1_readw(dev, SA_ADDR, sa_t, sa_status, DISABLEIRQS)) |
| & STAT_COMPLETE) == 0) { |
| if (time_after(jiffies, timeout)) |
| break; |
| } |
| |
| if ((status & (STAT_COMPLETE | STAT_OK)) != (STAT_COMPLETE | STAT_OK)) { |
| printk (KERN_WARNING "%s: can't initialise 82586: set address status %04X\n", dev->name, status); |
| printk (KERN_DEBUG "%s: SCB=[STS=%04X CMD=%04X CBL=%04X RFA=%04X]\n", dev->name, |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_command, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_rfa_offset, NORMALIRQS)); |
| failures += 1; |
| } |
| |
| timeout += HZ/10; |
| while (((status = ether1_readw(dev, MC_ADDR, mc_t, mc_status, DISABLEIRQS)) |
| & STAT_COMPLETE) == 0) { |
| if (time_after(jiffies, timeout)) |
| break; |
| } |
| |
| if ((status & (STAT_COMPLETE | STAT_OK)) != (STAT_COMPLETE | STAT_OK)) { |
| printk (KERN_WARNING "%s: can't initialise 82586: set multicast status %04X\n", dev->name, status); |
| printk (KERN_DEBUG "%s: SCB=[STS=%04X CMD=%04X CBL=%04X RFA=%04X]\n", dev->name, |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_command, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_rfa_offset, NORMALIRQS)); |
| failures += 1; |
| } |
| |
| timeout += HZ; |
| while (((status = ether1_readw(dev, TDR_ADDR, tdr_t, tdr_status, DISABLEIRQS)) |
| & STAT_COMPLETE) == 0) { |
| if (time_after(jiffies, timeout)) |
| break; |
| } |
| |
| if ((status & (STAT_COMPLETE | STAT_OK)) != (STAT_COMPLETE | STAT_OK)) { |
| printk (KERN_WARNING "%s: can't tdr (ignored)\n", dev->name); |
| printk (KERN_DEBUG "%s: SCB=[STS=%04X CMD=%04X CBL=%04X RFA=%04X]\n", dev->name, |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_command, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS), |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_rfa_offset, NORMALIRQS)); |
| } else { |
| status = ether1_readw(dev, TDR_ADDR, tdr_t, tdr_result, DISABLEIRQS); |
| if (status & TDR_XCVRPROB) |
| printk (KERN_WARNING "%s: i/f failed tdr: transceiver problem\n", dev->name); |
| else if ((status & (TDR_SHORT|TDR_OPEN)) && (status & TDR_TIME)) { |
| #ifdef FANCY |
| printk (KERN_WARNING "%s: i/f failed tdr: cable %s %d.%d us away\n", dev->name, |
| status & TDR_SHORT ? "short" : "open", (status & TDR_TIME) / 10, |
| (status & TDR_TIME) % 10); |
| #else |
| printk (KERN_WARNING "%s: i/f failed tdr: cable %s %d clks away\n", dev->name, |
| status & TDR_SHORT ? "short" : "open", (status & TDR_TIME)); |
| #endif |
| } |
| } |
| |
| if (failures) |
| ether1_reset (dev); |
| return failures ? 1 : 0; |
| } |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| static int |
| ether1_txalloc (struct net_device *dev, int size) |
| { |
| int start, tail; |
| |
| size = (size + 1) & ~1; |
| tail = priv(dev)->tx_tail; |
| |
| if (priv(dev)->tx_head + size > TX_AREA_END) { |
| if (tail > priv(dev)->tx_head) |
| return -1; |
| start = TX_AREA_START; |
| if (start + size > tail) |
| return -1; |
| priv(dev)->tx_head = start + size; |
| } else { |
| if (priv(dev)->tx_head < tail && (priv(dev)->tx_head + size) > tail) |
| return -1; |
| start = priv(dev)->tx_head; |
| priv(dev)->tx_head += size; |
| } |
| |
| return start; |
| } |
| |
| static int |
| ether1_open (struct net_device *dev) |
| { |
| if (request_irq(dev->irq, ether1_interrupt, 0, "ether1", dev)) |
| return -EAGAIN; |
| |
| if (ether1_init_for_open (dev)) { |
| free_irq (dev->irq, dev); |
| return -EAGAIN; |
| } |
| |
| netif_start_queue(dev); |
| |
| return 0; |
| } |
| |
| static void |
| ether1_timeout(struct net_device *dev) |
| { |
| printk(KERN_WARNING "%s: transmit timeout, network cable problem?\n", |
| dev->name); |
| printk(KERN_WARNING "%s: resetting device\n", dev->name); |
| |
| ether1_reset (dev); |
| |
| if (ether1_init_for_open (dev)) |
| printk (KERN_ERR "%s: unable to restart interface\n", dev->name); |
| |
| dev->stats.tx_errors++; |
| netif_wake_queue(dev); |
| } |
| |
| static int |
| ether1_sendpacket (struct sk_buff *skb, struct net_device *dev) |
| { |
| int tmp, tst, nopaddr, txaddr, tbdaddr, dataddr; |
| unsigned long flags; |
| tx_t tx; |
| tbd_t tbd; |
| nop_t nop; |
| |
| if (priv(dev)->restart) { |
| printk(KERN_WARNING "%s: resetting device\n", dev->name); |
| |
| ether1_reset(dev); |
| |
| if (ether1_init_for_open(dev)) |
| printk(KERN_ERR "%s: unable to restart interface\n", dev->name); |
| else |
| priv(dev)->restart = 0; |
| } |
| |
| if (skb->len < ETH_ZLEN) { |
| if (skb_padto(skb, ETH_ZLEN)) |
| goto out; |
| } |
| |
| /* |
| * insert packet followed by a nop |
| */ |
| txaddr = ether1_txalloc (dev, TX_SIZE); |
| tbdaddr = ether1_txalloc (dev, TBD_SIZE); |
| dataddr = ether1_txalloc (dev, skb->len); |
| nopaddr = ether1_txalloc (dev, NOP_SIZE); |
| |
| tx.tx_status = 0; |
| tx.tx_command = CMD_TX | CMD_INTR; |
| tx.tx_link = nopaddr; |
| tx.tx_tbdoffset = tbdaddr; |
| tbd.tbd_opts = TBD_EOL | skb->len; |
| tbd.tbd_link = I82586_NULL; |
| tbd.tbd_bufl = dataddr; |
| tbd.tbd_bufh = 0; |
| nop.nop_status = 0; |
| nop.nop_command = CMD_NOP; |
| nop.nop_link = nopaddr; |
| |
| local_irq_save(flags); |
| ether1_writebuffer (dev, &tx, txaddr, TX_SIZE); |
| ether1_writebuffer (dev, &tbd, tbdaddr, TBD_SIZE); |
| ether1_writebuffer (dev, skb->data, dataddr, skb->len); |
| ether1_writebuffer (dev, &nop, nopaddr, NOP_SIZE); |
| tmp = priv(dev)->tx_link; |
| priv(dev)->tx_link = nopaddr; |
| |
| /* now reset the previous nop pointer */ |
| ether1_writew(dev, txaddr, tmp, nop_t, nop_link, NORMALIRQS); |
| |
| local_irq_restore(flags); |
| |
| /* handle transmit */ |
| |
| /* check to see if we have room for a full sized ether frame */ |
| tmp = priv(dev)->tx_head; |
| tst = ether1_txalloc (dev, TX_SIZE + TBD_SIZE + NOP_SIZE + ETH_FRAME_LEN); |
| priv(dev)->tx_head = tmp; |
| dev_kfree_skb (skb); |
| |
| if (tst == -1) |
| netif_stop_queue(dev); |
| |
| out: |
| return NETDEV_TX_OK; |
| } |
| |
| static void |
| ether1_xmit_done (struct net_device *dev) |
| { |
| nop_t nop; |
| int caddr, tst; |
| |
| caddr = priv(dev)->tx_tail; |
| |
| again: |
| ether1_readbuffer (dev, &nop, caddr, NOP_SIZE); |
| |
| switch (nop.nop_command & CMD_MASK) { |
| case CMD_TDR: |
| /* special case */ |
| if (ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS) |
| != (unsigned short)I82586_NULL) { |
| ether1_writew(dev, SCB_CMDCUCSTART | SCB_CMDRXSTART, SCB_ADDR, scb_t, |
| scb_command, NORMALIRQS); |
| writeb(CTRL_CA, REG_CONTROL); |
| } |
| priv(dev)->tx_tail = NOP_ADDR; |
| return; |
| |
| case CMD_NOP: |
| if (nop.nop_link == caddr) { |
| if (priv(dev)->initialising == 0) |
| printk (KERN_WARNING "%s: strange command complete with no tx command!\n", dev->name); |
| else |
| priv(dev)->initialising = 0; |
| return; |
| } |
| if (caddr == nop.nop_link) |
| return; |
| caddr = nop.nop_link; |
| goto again; |
| |
| case CMD_TX: |
| if (nop.nop_status & STAT_COMPLETE) |
| break; |
| printk (KERN_ERR "%s: strange command complete without completed command\n", dev->name); |
| priv(dev)->restart = 1; |
| return; |
| |
| default: |
| printk (KERN_WARNING "%s: strange command %d complete! (offset %04X)", dev->name, |
| nop.nop_command & CMD_MASK, caddr); |
| priv(dev)->restart = 1; |
| return; |
| } |
| |
| while (nop.nop_status & STAT_COMPLETE) { |
| if (nop.nop_status & STAT_OK) { |
| dev->stats.tx_packets++; |
| dev->stats.collisions += (nop.nop_status & STAT_COLLISIONS); |
| } else { |
| dev->stats.tx_errors++; |
| |
| if (nop.nop_status & STAT_COLLAFTERTX) |
| dev->stats.collisions++; |
| if (nop.nop_status & STAT_NOCARRIER) |
| dev->stats.tx_carrier_errors++; |
| if (nop.nop_status & STAT_TXLOSTCTS) |
| printk (KERN_WARNING "%s: cts lost\n", dev->name); |
| if (nop.nop_status & STAT_TXSLOWDMA) |
| dev->stats.tx_fifo_errors++; |
| if (nop.nop_status & STAT_COLLEXCESSIVE) |
| dev->stats.collisions += 16; |
| } |
| |
| if (nop.nop_link == caddr) { |
| printk (KERN_ERR "%s: tx buffer chaining error: tx command points to itself\n", dev->name); |
| break; |
| } |
| |
| caddr = nop.nop_link; |
| ether1_readbuffer (dev, &nop, caddr, NOP_SIZE); |
| if ((nop.nop_command & CMD_MASK) != CMD_NOP) { |
| printk (KERN_ERR "%s: tx buffer chaining error: no nop after tx command\n", dev->name); |
| break; |
| } |
| |
| if (caddr == nop.nop_link) |
| break; |
| |
| caddr = nop.nop_link; |
| ether1_readbuffer (dev, &nop, caddr, NOP_SIZE); |
| if ((nop.nop_command & CMD_MASK) != CMD_TX) { |
| printk (KERN_ERR "%s: tx buffer chaining error: no tx command after nop\n", dev->name); |
| break; |
| } |
| } |
| priv(dev)->tx_tail = caddr; |
| |
| caddr = priv(dev)->tx_head; |
| tst = ether1_txalloc (dev, TX_SIZE + TBD_SIZE + NOP_SIZE + ETH_FRAME_LEN); |
| priv(dev)->tx_head = caddr; |
| if (tst != -1) |
| netif_wake_queue(dev); |
| } |
| |
| static void |
| ether1_recv_done (struct net_device *dev) |
| { |
| int status; |
| int nexttail, rbdaddr; |
| rbd_t rbd; |
| |
| do { |
| status = ether1_readw(dev, priv(dev)->rx_head, rfd_t, rfd_status, NORMALIRQS); |
| if ((status & RFD_COMPLETE) == 0) |
| break; |
| |
| rbdaddr = ether1_readw(dev, priv(dev)->rx_head, rfd_t, rfd_rbdoffset, NORMALIRQS); |
| ether1_readbuffer (dev, &rbd, rbdaddr, RBD_SIZE); |
| |
| if ((rbd.rbd_status & (RBD_EOF | RBD_ACNTVALID)) == (RBD_EOF | RBD_ACNTVALID)) { |
| int length = rbd.rbd_status & RBD_ACNT; |
| struct sk_buff *skb; |
| |
| length = (length + 1) & ~1; |
| skb = netdev_alloc_skb(dev, length + 2); |
| |
| if (skb) { |
| skb_reserve (skb, 2); |
| |
| ether1_readbuffer (dev, skb_put (skb, length), rbd.rbd_bufl, length); |
| |
| skb->protocol = eth_type_trans (skb, dev); |
| netif_rx (skb); |
| dev->stats.rx_packets++; |
| } else |
| dev->stats.rx_dropped++; |
| } else { |
| printk(KERN_WARNING "%s: %s\n", dev->name, |
| (rbd.rbd_status & RBD_EOF) ? "oversized packet" : "acnt not valid"); |
| dev->stats.rx_dropped++; |
| } |
| |
| nexttail = ether1_readw(dev, priv(dev)->rx_tail, rfd_t, rfd_link, NORMALIRQS); |
| /* nexttail should be rx_head */ |
| if (nexttail != priv(dev)->rx_head) |
| printk(KERN_ERR "%s: receiver buffer chaining error (%04X != %04X)\n", |
| dev->name, nexttail, priv(dev)->rx_head); |
| ether1_writew(dev, RFD_CMDEL | RFD_CMDSUSPEND, nexttail, rfd_t, rfd_command, NORMALIRQS); |
| ether1_writew(dev, 0, priv(dev)->rx_tail, rfd_t, rfd_command, NORMALIRQS); |
| ether1_writew(dev, 0, priv(dev)->rx_tail, rfd_t, rfd_status, NORMALIRQS); |
| ether1_writew(dev, 0, priv(dev)->rx_tail, rfd_t, rfd_rbdoffset, NORMALIRQS); |
| |
| priv(dev)->rx_tail = nexttail; |
| priv(dev)->rx_head = ether1_readw(dev, priv(dev)->rx_head, rfd_t, rfd_link, NORMALIRQS); |
| } while (1); |
| } |
| |
| static irqreturn_t |
| ether1_interrupt (int irq, void *dev_id) |
| { |
| struct net_device *dev = (struct net_device *)dev_id; |
| int status; |
| |
| status = ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS); |
| |
| if (status) { |
| ether1_writew(dev, status & (SCB_STRNR | SCB_STCNA | SCB_STFR | SCB_STCX), |
| SCB_ADDR, scb_t, scb_command, NORMALIRQS); |
| writeb(CTRL_CA | CTRL_ACK, REG_CONTROL); |
| if (status & SCB_STCX) { |
| ether1_xmit_done (dev); |
| } |
| if (status & SCB_STCNA) { |
| if (priv(dev)->resetting == 0) |
| printk (KERN_WARNING "%s: CU went not ready ???\n", dev->name); |
| else |
| priv(dev)->resetting += 1; |
| if (ether1_readw(dev, SCB_ADDR, scb_t, scb_cbl_offset, NORMALIRQS) |
| != (unsigned short)I82586_NULL) { |
| ether1_writew(dev, SCB_CMDCUCSTART, SCB_ADDR, scb_t, scb_command, NORMALIRQS); |
| writeb(CTRL_CA, REG_CONTROL); |
| } |
| if (priv(dev)->resetting == 2) |
| priv(dev)->resetting = 0; |
| } |
| if (status & SCB_STFR) { |
| ether1_recv_done (dev); |
| } |
| if (status & SCB_STRNR) { |
| if (ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS) & SCB_STRXSUSP) { |
| printk (KERN_WARNING "%s: RU went not ready: RU suspended\n", dev->name); |
| ether1_writew(dev, SCB_CMDRXRESUME, SCB_ADDR, scb_t, scb_command, NORMALIRQS); |
| writeb(CTRL_CA, REG_CONTROL); |
| dev->stats.rx_dropped++; /* we suspended due to lack of buffer space */ |
| } else |
| printk(KERN_WARNING "%s: RU went not ready: %04X\n", dev->name, |
| ether1_readw(dev, SCB_ADDR, scb_t, scb_status, NORMALIRQS)); |
| printk (KERN_WARNING "RU ptr = %04X\n", ether1_readw(dev, SCB_ADDR, scb_t, scb_rfa_offset, |
| NORMALIRQS)); |
| } |
| } else |
| writeb(CTRL_ACK, REG_CONTROL); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int |
| ether1_close (struct net_device *dev) |
| { |
| ether1_reset (dev); |
| |
| free_irq(dev->irq, dev); |
| |
| return 0; |
| } |
| |
| /* |
| * Set or clear the multicast filter for this adaptor. |
| * num_addrs == -1 Promiscuous mode, receive all packets. |
| * num_addrs == 0 Normal mode, clear multicast list. |
| * num_addrs > 0 Multicast mode, receive normal and MC packets, and do |
| * best-effort filtering. |
| */ |
| static void |
| ether1_setmulticastlist (struct net_device *dev) |
| { |
| } |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| static void ether1_banner(void) |
| { |
| static unsigned int version_printed = 0; |
| |
| if (net_debug && version_printed++ == 0) |
| printk(KERN_INFO "%s", version); |
| } |
| |
| static const struct net_device_ops ether1_netdev_ops = { |
| .ndo_open = ether1_open, |
| .ndo_stop = ether1_close, |
| .ndo_start_xmit = ether1_sendpacket, |
| .ndo_set_rx_mode = ether1_setmulticastlist, |
| .ndo_tx_timeout = ether1_timeout, |
| .ndo_validate_addr = eth_validate_addr, |
| .ndo_set_mac_address = eth_mac_addr, |
| }; |
| |
| static int |
| ether1_probe(struct expansion_card *ec, const struct ecard_id *id) |
| { |
| struct net_device *dev; |
| int i, ret = 0; |
| |
| ether1_banner(); |
| |
| ret = ecard_request_resources(ec); |
| if (ret) |
| goto out; |
| |
| dev = alloc_etherdev(sizeof(struct ether1_priv)); |
| if (!dev) { |
| ret = -ENOMEM; |
| goto release; |
| } |
| |
| SET_NETDEV_DEV(dev, &ec->dev); |
| |
| dev->irq = ec->irq; |
| priv(dev)->base = ecardm_iomap(ec, ECARD_RES_IOCFAST, 0, 0); |
| if (!priv(dev)->base) { |
| ret = -ENOMEM; |
| goto free; |
| } |
| |
| if ((priv(dev)->bus_type = ether1_reset(dev)) == 0) { |
| ret = -ENODEV; |
| goto free; |
| } |
| |
| for (i = 0; i < 6; i++) |
| dev->dev_addr[i] = readb(IDPROM_ADDRESS + (i << 2)); |
| |
| if (ether1_init_2(dev)) { |
| ret = -ENODEV; |
| goto free; |
| } |
| |
| dev->netdev_ops = ðer1_netdev_ops; |
| dev->watchdog_timeo = 5 * HZ / 100; |
| |
| ret = register_netdev(dev); |
| if (ret) |
| goto free; |
| |
| printk(KERN_INFO "%s: ether1 in slot %d, %pM\n", |
| dev->name, ec->slot_no, dev->dev_addr); |
| |
| ecard_set_drvdata(ec, dev); |
| return 0; |
| |
| free: |
| free_netdev(dev); |
| release: |
| ecard_release_resources(ec); |
| out: |
| return ret; |
| } |
| |
| static void ether1_remove(struct expansion_card *ec) |
| { |
| struct net_device *dev = ecard_get_drvdata(ec); |
| |
| ecard_set_drvdata(ec, NULL); |
| |
| unregister_netdev(dev); |
| free_netdev(dev); |
| ecard_release_resources(ec); |
| } |
| |
| static const struct ecard_id ether1_ids[] = { |
| { MANU_ACORN, PROD_ACORN_ETHER1 }, |
| { 0xffff, 0xffff } |
| }; |
| |
| static struct ecard_driver ether1_driver = { |
| .probe = ether1_probe, |
| .remove = ether1_remove, |
| .id_table = ether1_ids, |
| .drv = { |
| .name = "ether1", |
| }, |
| }; |
| |
| static int __init ether1_init(void) |
| { |
| return ecard_register_driver(ðer1_driver); |
| } |
| |
| static void __exit ether1_exit(void) |
| { |
| ecard_remove_driver(ðer1_driver); |
| } |
| |
| module_init(ether1_init); |
| module_exit(ether1_exit); |
| |
| MODULE_LICENSE("GPL"); |