| #!/bin/bash | |
| # SPDX-License-Identifier: GPL-2.0 | |
| # | |
| # Run traceroute/traceroute6 tests | |
| # | |
| source lib.sh | |
| VERBOSE=0 | |
| PAUSE_ON_FAIL=no | |
| ################################################################################ | |
| # | |
| run_cmd() | |
| { | |
| local ns | |
| local cmd | |
| local out | |
| local rc | |
| ns="$1" | |
| shift | |
| cmd="$*" | |
| if [ "$VERBOSE" = "1" ]; then | |
| printf " COMMAND: $cmd\n" | |
| fi | |
| out=$(eval ip netns exec ${ns} ${cmd} 2>&1) | |
| rc=$? | |
| if [ "$VERBOSE" = "1" -a -n "$out" ]; then | |
| echo " $out" | |
| fi | |
| [ "$VERBOSE" = "1" ] && echo | |
| return $rc | |
| } | |
| ################################################################################ | |
| # create namespaces and interconnects | |
| create_ns() | |
| { | |
| local ns=$1 | |
| local addr=$2 | |
| local addr6=$3 | |
| [ -z "${addr}" ] && addr="-" | |
| [ -z "${addr6}" ] && addr6="-" | |
| if [ "${addr}" != "-" ]; then | |
| ip netns exec ${ns} ip addr add dev lo ${addr} | |
| fi | |
| if [ "${addr6}" != "-" ]; then | |
| ip netns exec ${ns} ip -6 addr add dev lo ${addr6} | |
| fi | |
| ip netns exec ${ns} ip ro add unreachable default metric 8192 | |
| ip netns exec ${ns} ip -6 ro add unreachable default metric 8192 | |
| ip netns exec ${ns} sysctl -qw net.ipv4.ip_forward=1 | |
| ip netns exec ${ns} sysctl -qw net.ipv6.conf.all.keep_addr_on_down=1 | |
| ip netns exec ${ns} sysctl -qw net.ipv6.conf.all.forwarding=1 | |
| ip netns exec ${ns} sysctl -qw net.ipv6.conf.default.forwarding=1 | |
| ip netns exec ${ns} sysctl -qw net.ipv6.conf.default.accept_dad=0 | |
| } | |
| # create veth pair to connect namespaces and apply addresses. | |
| connect_ns() | |
| { | |
| local ns1=$1 | |
| local ns1_dev=$2 | |
| local ns1_addr=$3 | |
| local ns1_addr6=$4 | |
| local ns2=$5 | |
| local ns2_dev=$6 | |
| local ns2_addr=$7 | |
| local ns2_addr6=$8 | |
| ip netns exec ${ns1} ip li add ${ns1_dev} type veth peer name tmp | |
| ip netns exec ${ns1} ip li set ${ns1_dev} up | |
| ip netns exec ${ns1} ip li set tmp netns ${ns2} name ${ns2_dev} | |
| ip netns exec ${ns2} ip li set ${ns2_dev} up | |
| if [ "${ns1_addr}" != "-" ]; then | |
| ip netns exec ${ns1} ip addr add dev ${ns1_dev} ${ns1_addr} | |
| fi | |
| if [ "${ns2_addr}" != "-" ]; then | |
| ip netns exec ${ns2} ip addr add dev ${ns2_dev} ${ns2_addr} | |
| fi | |
| if [ "${ns1_addr6}" != "-" ]; then | |
| ip netns exec ${ns1} ip addr add dev ${ns1_dev} ${ns1_addr6} | |
| fi | |
| if [ "${ns2_addr6}" != "-" ]; then | |
| ip netns exec ${ns2} ip addr add dev ${ns2_dev} ${ns2_addr6} | |
| fi | |
| } | |
| ################################################################################ | |
| # traceroute6 test | |
| # | |
| # Verify that in this scenario | |
| # | |
| # ------------------------ N2 | |
| # | | | |
| # ------ ------ N3 ---- | |
| # | R1 | | R2 |------|H2| | |
| # ------ ------ ---- | |
| # | | | |
| # ------------------------ N1 | |
| # | | |
| # ---- | |
| # |H1| | |
| # ---- | |
| # | |
| # where H1's default route goes through R1 and R1's default route goes | |
| # through R2 over N2, traceroute6 from H1 to H2 reports R2's address | |
| # on N2 and not N1. | |
| # | |
| # Addresses are assigned as follows: | |
| # | |
| # N1: 2000:101::/64 | |
| # N2: 2000:102::/64 | |
| # N3: 2000:103::/64 | |
| # | |
| # R1's host part of address: 1 | |
| # R2's host part of address: 2 | |
| # H1's host part of address: 3 | |
| # H2's host part of address: 4 | |
| # | |
| # For example: | |
| # the IPv6 address of R1's interface on N2 is 2000:102::1/64 | |
| cleanup_traceroute6() | |
| { | |
| cleanup_ns $h1 $h2 $r1 $r2 | |
| } | |
| setup_traceroute6() | |
| { | |
| brdev=br0 | |
| # start clean | |
| cleanup_traceroute6 | |
| set -e | |
| setup_ns h1 h2 r1 r2 | |
| create_ns $h1 | |
| create_ns $h2 | |
| create_ns $r1 | |
| create_ns $r2 | |
| # Setup N3 | |
| connect_ns $r2 eth3 - 2000:103::2/64 $h2 eth3 - 2000:103::4/64 | |
| ip netns exec $h2 ip route add default via 2000:103::2 | |
| # Setup N2 | |
| connect_ns $r1 eth2 - 2000:102::1/64 $r2 eth2 - 2000:102::2/64 | |
| ip netns exec $r1 ip route add default via 2000:102::2 | |
| # Setup N1. host-1 and router-2 connect to a bridge in router-1. | |
| ip netns exec $r1 ip link add name ${brdev} type bridge | |
| ip netns exec $r1 ip link set ${brdev} up | |
| ip netns exec $r1 ip addr add 2000:101::1/64 dev ${brdev} | |
| connect_ns $h1 eth0 - 2000:101::3/64 $r1 eth0 - - | |
| ip netns exec $r1 ip link set dev eth0 master ${brdev} | |
| ip netns exec $h1 ip route add default via 2000:101::1 | |
| connect_ns $r2 eth1 - 2000:101::2/64 $r1 eth1 - - | |
| ip netns exec $r1 ip link set dev eth1 master ${brdev} | |
| # Prime the network | |
| ip netns exec $h1 ping6 -c5 2000:103::4 >/dev/null 2>&1 | |
| set +e | |
| } | |
| run_traceroute6() | |
| { | |
| setup_traceroute6 | |
| RET=0 | |
| # traceroute6 host-2 from host-1 (expects 2000:102::2) | |
| run_cmd $h1 "traceroute6 2000:103::4 | grep -q 2000:102::2" | |
| check_err $? "traceroute6 did not return 2000:102::2" | |
| log_test "IPv6 traceroute" | |
| cleanup_traceroute6 | |
| } | |
| ################################################################################ | |
| # traceroute6 with VRF test | |
| # | |
| # Verify that in this scenario | |
| # | |
| # ------------------------ N2 | |
| # | | | |
| # ------ ------ N3 ---- | |
| # | R1 | | R2 |------|H2| | |
| # ------ ------ ---- | |
| # | | | |
| # ------------------------ N1 | |
| # | | |
| # ---- | |
| # |H1| | |
| # ---- | |
| # | |
| # Where H1's default route goes through R1 and R1's default route goes through | |
| # R2 over N2, traceroute6 from H1 to H2 reports R2's address on N2 and not N1. | |
| # The interfaces connecting R2 to the different subnets are membmer in a VRF | |
| # and the intention is to check that traceroute6 does not report the VRF's | |
| # address. | |
| # | |
| # Addresses are assigned as follows: | |
| # | |
| # N1: 2000:101::/64 | |
| # N2: 2000:102::/64 | |
| # N3: 2000:103::/64 | |
| # | |
| # R1's host part of address: 1 | |
| # R2's host part of address: 2 | |
| # H1's host part of address: 3 | |
| # H2's host part of address: 4 | |
| # | |
| # For example: | |
| # the IPv6 address of R1's interface on N2 is 2000:102::1/64 | |
| cleanup_traceroute6_vrf() | |
| { | |
| cleanup_all_ns | |
| } | |
| setup_traceroute6_vrf() | |
| { | |
| # Start clean | |
| cleanup_traceroute6_vrf | |
| setup_ns h1 h2 r1 r2 | |
| create_ns "$h1" | |
| create_ns "$h2" | |
| create_ns "$r1" | |
| create_ns "$r2" | |
| ip -n "$r2" link add name vrf100 up type vrf table 100 | |
| ip -n "$r2" addr add 2001:db8:100::1/64 dev vrf100 | |
| # Setup N3 | |
| connect_ns "$r2" eth3 - 2000:103::2/64 "$h2" eth3 - 2000:103::4/64 | |
| ip -n "$r2" link set dev eth3 master vrf100 | |
| ip -n "$h2" route add default via 2000:103::2 | |
| # Setup N2 | |
| connect_ns "$r1" eth2 - 2000:102::1/64 "$r2" eth2 - 2000:102::2/64 | |
| ip -n "$r1" route add default via 2000:102::2 | |
| ip -n "$r2" link set dev eth2 master vrf100 | |
| # Setup N1. host-1 and router-2 connect to a bridge in router-1. | |
| ip -n "$r1" link add name br100 up type bridge | |
| ip -n "$r1" addr add 2000:101::1/64 dev br100 | |
| connect_ns "$h1" eth0 - 2000:101::3/64 "$r1" eth0 - - | |
| ip -n "$h1" route add default via 2000:101::1 | |
| ip -n "$r1" link set dev eth0 master br100 | |
| connect_ns "$r2" eth1 - 2000:101::2/64 "$r1" eth1 - - | |
| ip -n "$r2" link set dev eth1 master vrf100 | |
| ip -n "$r1" link set dev eth1 master br100 | |
| # Prime the network | |
| ip netns exec "$h1" ping6 -c5 2000:103::4 >/dev/null 2>&1 | |
| } | |
| run_traceroute6_vrf() | |
| { | |
| setup_traceroute6_vrf | |
| RET=0 | |
| # traceroute6 host-2 from host-1 (expects 2000:102::2) | |
| run_cmd "$h1" "traceroute6 2000:103::4 | grep 2000:102::2" | |
| check_err $? "traceroute6 did not return 2000:102::2" | |
| log_test "IPv6 traceroute with VRF" | |
| cleanup_traceroute6_vrf | |
| } | |
| ################################################################################ | |
| # traceroute test | |
| # | |
| # Verify that traceroute from H1 to H2 shows 1.0.3.1 and 1.0.1.1 when | |
| # traceroute uses 1.0.3.3 and 1.0.1.3 as the source IP, respectively. | |
| # | |
| # 1.0.3.3/24 1.0.3.1/24 | |
| # ---- 1.0.1.3/24 1.0.1.1/24 ---- 1.0.2.1/24 1.0.2.4/24 ---- | |
| # |H1|--------------------------|R1|--------------------------|H2| | |
| # ---- N1 ---- N2 ---- | |
| # | |
| # where net.ipv4.icmp_errors_use_inbound_ifaddr is set on R1 and 1.0.3.1/24 and | |
| # 1.0.1.1/24 are R1's primary addresses on N1. The kernel is expected to prefer | |
| # a source address that is on the same subnet as the destination IP of the ICMP | |
| # error message. | |
| cleanup_traceroute() | |
| { | |
| cleanup_ns $h1 $h2 $router | |
| } | |
| setup_traceroute() | |
| { | |
| # start clean | |
| cleanup_traceroute | |
| set -e | |
| setup_ns h1 h2 router | |
| create_ns $h1 | |
| create_ns $h2 | |
| create_ns $router | |
| connect_ns $h1 eth0 1.0.1.3/24 - \ | |
| $router eth1 1.0.3.1/24 - | |
| ip -n "$h1" addr add 1.0.3.3/24 dev eth0 | |
| ip netns exec $h1 ip route add default via 1.0.1.1 | |
| ip netns exec $router ip addr add 1.0.1.1/24 dev eth1 | |
| ip netns exec $router sysctl -qw \ | |
| net.ipv4.icmp_errors_use_inbound_ifaddr=1 | |
| connect_ns $h2 eth0 1.0.2.4/24 - \ | |
| $router eth2 1.0.2.1/24 - | |
| ip netns exec $h2 ip route add default via 1.0.2.1 | |
| # Prime the network | |
| ip netns exec $h1 ping -c5 1.0.2.4 >/dev/null 2>&1 | |
| set +e | |
| } | |
| run_traceroute() | |
| { | |
| setup_traceroute | |
| RET=0 | |
| # traceroute host-2 from host-1. Expect a source IP that is on the same | |
| # subnet as destination IP of the ICMP error message. | |
| run_cmd "$h1" "traceroute -s 1.0.1.3 1.0.2.4 | grep -q 1.0.1.1" | |
| check_err $? "traceroute did not return 1.0.1.1" | |
| run_cmd "$h1" "traceroute -s 1.0.3.3 1.0.2.4 | grep -q 1.0.3.1" | |
| check_err $? "traceroute did not return 1.0.3.1" | |
| log_test "IPv4 traceroute" | |
| cleanup_traceroute | |
| } | |
| ################################################################################ | |
| # traceroute with VRF test | |
| # | |
| # Verify that traceroute from H1 to H2 shows 1.0.3.1 and 1.0.1.1 when | |
| # traceroute uses 1.0.3.3 and 1.0.1.3 as the source IP, respectively. The | |
| # intention is to check that the kernel does not choose an IP assigned to the | |
| # VRF device, but rather an address from the VRF port (eth1) that received the | |
| # packet that generates the ICMP error message. | |
| # | |
| # 1.0.4.1/24 (vrf100) | |
| # 1.0.3.3/24 1.0.3.1/24 | |
| # ---- 1.0.1.3/24 1.0.1.1/24 ---- 1.0.2.1/24 1.0.2.4/24 ---- | |
| # |H1|--------------------------|R1|--------------------------|H2| | |
| # ---- N1 ---- N2 ---- | |
| cleanup_traceroute_vrf() | |
| { | |
| cleanup_all_ns | |
| } | |
| setup_traceroute_vrf() | |
| { | |
| # Start clean | |
| cleanup_traceroute_vrf | |
| setup_ns h1 h2 router | |
| create_ns "$h1" | |
| create_ns "$h2" | |
| create_ns "$router" | |
| ip -n "$router" link add name vrf100 up type vrf table 100 | |
| ip -n "$router" addr add 1.0.4.1/24 dev vrf100 | |
| connect_ns "$h1" eth0 1.0.1.3/24 - \ | |
| "$router" eth1 1.0.1.1/24 - | |
| ip -n "$h1" addr add 1.0.3.3/24 dev eth0 | |
| ip -n "$h1" route add default via 1.0.1.1 | |
| ip -n "$router" link set dev eth1 master vrf100 | |
| ip -n "$router" addr add 1.0.3.1/24 dev eth1 | |
| ip netns exec "$router" sysctl -qw \ | |
| net.ipv4.icmp_errors_use_inbound_ifaddr=1 | |
| connect_ns "$h2" eth0 1.0.2.4/24 - \ | |
| "$router" eth2 1.0.2.1/24 - | |
| ip -n "$h2" route add default via 1.0.2.1 | |
| ip -n "$router" link set dev eth2 master vrf100 | |
| # Prime the network | |
| ip netns exec "$h1" ping -c5 1.0.2.4 >/dev/null 2>&1 | |
| } | |
| run_traceroute_vrf() | |
| { | |
| setup_traceroute_vrf | |
| RET=0 | |
| # traceroute host-2 from host-1. Expect a source IP that is on the same | |
| # subnet as destination IP of the ICMP error message. | |
| run_cmd "$h1" "traceroute -s 1.0.1.3 1.0.2.4 | grep 1.0.1.1" | |
| check_err $? "traceroute did not return 1.0.1.1" | |
| run_cmd "$h1" "traceroute -s 1.0.3.3 1.0.2.4 | grep 1.0.3.1" | |
| check_err $? "traceroute did not return 1.0.3.1" | |
| log_test "IPv4 traceroute with VRF" | |
| cleanup_traceroute_vrf | |
| } | |
| ################################################################################ | |
| # Run tests | |
| run_tests() | |
| { | |
| run_traceroute6 | |
| run_traceroute6_vrf | |
| run_traceroute | |
| run_traceroute_vrf | |
| } | |
| ################################################################################ | |
| # main | |
| while getopts :pv o | |
| do | |
| case $o in | |
| p) PAUSE_ON_FAIL=yes;; | |
| v) VERBOSE=$(($VERBOSE + 1));; | |
| *) exit 1;; | |
| esac | |
| done | |
| require_command traceroute6 | |
| require_command traceroute | |
| run_tests | |
| exit "${EXIT_STATUS}" |