| /* | |
| * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved. | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 and | |
| * only version 2 as published by the Free Software Foundation. | |
| * | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| */ | |
| #include <linux/clk.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/regulator/consumer.h> | |
| #include <drm/drm_crtc.h> | |
| #include <drm/drm_dp_helper.h> | |
| #include <drm/drm_edid.h> | |
| #include "edp.h" | |
| #include "edp.xml.h" | |
| #define VDDA_UA_ON_LOAD 100000 /* uA units */ | |
| #define VDDA_UA_OFF_LOAD 100 /* uA units */ | |
| #define DPCD_LINK_VOLTAGE_MAX 4 | |
| #define DPCD_LINK_PRE_EMPHASIS_MAX 4 | |
| #define EDP_LINK_BW_MAX DP_LINK_BW_2_7 | |
| /* Link training return value */ | |
| #define EDP_TRAIN_FAIL -1 | |
| #define EDP_TRAIN_SUCCESS 0 | |
| #define EDP_TRAIN_RECONFIG 1 | |
| #define EDP_CLK_MASK_AHB BIT(0) | |
| #define EDP_CLK_MASK_AUX BIT(1) | |
| #define EDP_CLK_MASK_LINK BIT(2) | |
| #define EDP_CLK_MASK_PIXEL BIT(3) | |
| #define EDP_CLK_MASK_MDP_CORE BIT(4) | |
| #define EDP_CLK_MASK_LINK_CHAN (EDP_CLK_MASK_LINK | EDP_CLK_MASK_PIXEL) | |
| #define EDP_CLK_MASK_AUX_CHAN \ | |
| (EDP_CLK_MASK_AHB | EDP_CLK_MASK_AUX | EDP_CLK_MASK_MDP_CORE) | |
| #define EDP_CLK_MASK_ALL (EDP_CLK_MASK_AUX_CHAN | EDP_CLK_MASK_LINK_CHAN) | |
| #define EDP_BACKLIGHT_MAX 255 | |
| #define EDP_INTR_STATUS1 \ | |
| (EDP_INTERRUPT_REG_1_HPD | EDP_INTERRUPT_REG_1_AUX_I2C_DONE | \ | |
| EDP_INTERRUPT_REG_1_WRONG_ADDR | EDP_INTERRUPT_REG_1_TIMEOUT | \ | |
| EDP_INTERRUPT_REG_1_NACK_DEFER | EDP_INTERRUPT_REG_1_WRONG_DATA_CNT | \ | |
| EDP_INTERRUPT_REG_1_I2C_NACK | EDP_INTERRUPT_REG_1_I2C_DEFER | \ | |
| EDP_INTERRUPT_REG_1_PLL_UNLOCK | EDP_INTERRUPT_REG_1_AUX_ERROR) | |
| #define EDP_INTR_MASK1 (EDP_INTR_STATUS1 << 2) | |
| #define EDP_INTR_STATUS2 \ | |
| (EDP_INTERRUPT_REG_2_READY_FOR_VIDEO | \ | |
| EDP_INTERRUPT_REG_2_IDLE_PATTERNs_SENT | \ | |
| EDP_INTERRUPT_REG_2_FRAME_END | EDP_INTERRUPT_REG_2_CRC_UPDATED) | |
| #define EDP_INTR_MASK2 (EDP_INTR_STATUS2 << 2) | |
| struct edp_ctrl { | |
| struct platform_device *pdev; | |
| void __iomem *base; | |
| /* regulators */ | |
| struct regulator *vdda_vreg; /* 1.8 V */ | |
| struct regulator *lvl_vreg; | |
| /* clocks */ | |
| struct clk *aux_clk; | |
| struct clk *pixel_clk; | |
| struct clk *ahb_clk; | |
| struct clk *link_clk; | |
| struct clk *mdp_core_clk; | |
| /* gpios */ | |
| struct gpio_desc *panel_en_gpio; | |
| struct gpio_desc *panel_hpd_gpio; | |
| /* completion and mutex */ | |
| struct completion idle_comp; | |
| struct mutex dev_mutex; /* To protect device power status */ | |
| /* work queue */ | |
| struct work_struct on_work; | |
| struct work_struct off_work; | |
| struct workqueue_struct *workqueue; | |
| /* Interrupt register lock */ | |
| spinlock_t irq_lock; | |
| bool edp_connected; | |
| bool power_on; | |
| /* edid raw data */ | |
| struct edid *edid; | |
| struct drm_dp_link dp_link; | |
| struct drm_dp_aux *drm_aux; | |
| /* dpcd raw data */ | |
| u8 dpcd[DP_RECEIVER_CAP_SIZE]; | |
| /* Link status */ | |
| u8 link_rate; | |
| u8 lane_cnt; | |
| u8 v_level; | |
| u8 p_level; | |
| /* Timing status */ | |
| u8 interlaced; | |
| u32 pixel_rate; /* in kHz */ | |
| u32 color_depth; | |
| struct edp_aux *aux; | |
| struct edp_phy *phy; | |
| }; | |
| struct edp_pixel_clk_div { | |
| u32 rate; /* in kHz */ | |
| u32 m; | |
| u32 n; | |
| }; | |
| #define EDP_PIXEL_CLK_NUM 8 | |
| static const struct edp_pixel_clk_div clk_divs[2][EDP_PIXEL_CLK_NUM] = { | |
| { /* Link clock = 162MHz, source clock = 810MHz */ | |
| {119000, 31, 211}, /* WSXGA+ 1680x1050@60Hz CVT */ | |
| {130250, 32, 199}, /* UXGA 1600x1200@60Hz CVT */ | |
| {148500, 11, 60}, /* FHD 1920x1080@60Hz */ | |
| {154000, 50, 263}, /* WUXGA 1920x1200@60Hz CVT */ | |
| {209250, 31, 120}, /* QXGA 2048x1536@60Hz CVT */ | |
| {268500, 119, 359}, /* WQXGA 2560x1600@60Hz CVT */ | |
| {138530, 33, 193}, /* AUO B116HAN03.0 Panel */ | |
| {141400, 48, 275}, /* AUO B133HTN01.2 Panel */ | |
| }, | |
| { /* Link clock = 270MHz, source clock = 675MHz */ | |
| {119000, 52, 295}, /* WSXGA+ 1680x1050@60Hz CVT */ | |
| {130250, 11, 57}, /* UXGA 1600x1200@60Hz CVT */ | |
| {148500, 11, 50}, /* FHD 1920x1080@60Hz */ | |
| {154000, 47, 206}, /* WUXGA 1920x1200@60Hz CVT */ | |
| {209250, 31, 100}, /* QXGA 2048x1536@60Hz CVT */ | |
| {268500, 107, 269}, /* WQXGA 2560x1600@60Hz CVT */ | |
| {138530, 63, 307}, /* AUO B116HAN03.0 Panel */ | |
| {141400, 53, 253}, /* AUO B133HTN01.2 Panel */ | |
| }, | |
| }; | |
| static int edp_clk_init(struct edp_ctrl *ctrl) | |
| { | |
| struct device *dev = &ctrl->pdev->dev; | |
| int ret; | |
| ctrl->aux_clk = devm_clk_get(dev, "core_clk"); | |
| if (IS_ERR(ctrl->aux_clk)) { | |
| ret = PTR_ERR(ctrl->aux_clk); | |
| pr_err("%s: Can't find aux_clk, %d\n", __func__, ret); | |
| ctrl->aux_clk = NULL; | |
| return ret; | |
| } | |
| ctrl->pixel_clk = devm_clk_get(dev, "pixel_clk"); | |
| if (IS_ERR(ctrl->pixel_clk)) { | |
| ret = PTR_ERR(ctrl->pixel_clk); | |
| pr_err("%s: Can't find pixel_clk, %d\n", __func__, ret); | |
| ctrl->pixel_clk = NULL; | |
| return ret; | |
| } | |
| ctrl->ahb_clk = devm_clk_get(dev, "iface_clk"); | |
| if (IS_ERR(ctrl->ahb_clk)) { | |
| ret = PTR_ERR(ctrl->ahb_clk); | |
| pr_err("%s: Can't find ahb_clk, %d\n", __func__, ret); | |
| ctrl->ahb_clk = NULL; | |
| return ret; | |
| } | |
| ctrl->link_clk = devm_clk_get(dev, "link_clk"); | |
| if (IS_ERR(ctrl->link_clk)) { | |
| ret = PTR_ERR(ctrl->link_clk); | |
| pr_err("%s: Can't find link_clk, %d\n", __func__, ret); | |
| ctrl->link_clk = NULL; | |
| return ret; | |
| } | |
| /* need mdp core clock to receive irq */ | |
| ctrl->mdp_core_clk = devm_clk_get(dev, "mdp_core_clk"); | |
| if (IS_ERR(ctrl->mdp_core_clk)) { | |
| ret = PTR_ERR(ctrl->mdp_core_clk); | |
| pr_err("%s: Can't find mdp_core_clk, %d\n", __func__, ret); | |
| ctrl->mdp_core_clk = NULL; | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static int edp_clk_enable(struct edp_ctrl *ctrl, u32 clk_mask) | |
| { | |
| int ret; | |
| DBG("mask=%x", clk_mask); | |
| /* ahb_clk should be enabled first */ | |
| if (clk_mask & EDP_CLK_MASK_AHB) { | |
| ret = clk_prepare_enable(ctrl->ahb_clk); | |
| if (ret) { | |
| pr_err("%s: Failed to enable ahb clk\n", __func__); | |
| goto f0; | |
| } | |
| } | |
| if (clk_mask & EDP_CLK_MASK_AUX) { | |
| ret = clk_set_rate(ctrl->aux_clk, 19200000); | |
| if (ret) { | |
| pr_err("%s: Failed to set rate aux clk\n", __func__); | |
| goto f1; | |
| } | |
| ret = clk_prepare_enable(ctrl->aux_clk); | |
| if (ret) { | |
| pr_err("%s: Failed to enable aux clk\n", __func__); | |
| goto f1; | |
| } | |
| } | |
| /* Need to set rate and enable link_clk prior to pixel_clk */ | |
| if (clk_mask & EDP_CLK_MASK_LINK) { | |
| DBG("edp->link_clk, set_rate %ld", | |
| (unsigned long)ctrl->link_rate * 27000000); | |
| ret = clk_set_rate(ctrl->link_clk, | |
| (unsigned long)ctrl->link_rate * 27000000); | |
| if (ret) { | |
| pr_err("%s: Failed to set rate to link clk\n", | |
| __func__); | |
| goto f2; | |
| } | |
| ret = clk_prepare_enable(ctrl->link_clk); | |
| if (ret) { | |
| pr_err("%s: Failed to enable link clk\n", __func__); | |
| goto f2; | |
| } | |
| } | |
| if (clk_mask & EDP_CLK_MASK_PIXEL) { | |
| DBG("edp->pixel_clk, set_rate %ld", | |
| (unsigned long)ctrl->pixel_rate * 1000); | |
| ret = clk_set_rate(ctrl->pixel_clk, | |
| (unsigned long)ctrl->pixel_rate * 1000); | |
| if (ret) { | |
| pr_err("%s: Failed to set rate to pixel clk\n", | |
| __func__); | |
| goto f3; | |
| } | |
| ret = clk_prepare_enable(ctrl->pixel_clk); | |
| if (ret) { | |
| pr_err("%s: Failed to enable pixel clk\n", __func__); | |
| goto f3; | |
| } | |
| } | |
| if (clk_mask & EDP_CLK_MASK_MDP_CORE) { | |
| ret = clk_prepare_enable(ctrl->mdp_core_clk); | |
| if (ret) { | |
| pr_err("%s: Failed to enable mdp core clk\n", __func__); | |
| goto f4; | |
| } | |
| } | |
| return 0; | |
| f4: | |
| if (clk_mask & EDP_CLK_MASK_PIXEL) | |
| clk_disable_unprepare(ctrl->pixel_clk); | |
| f3: | |
| if (clk_mask & EDP_CLK_MASK_LINK) | |
| clk_disable_unprepare(ctrl->link_clk); | |
| f2: | |
| if (clk_mask & EDP_CLK_MASK_AUX) | |
| clk_disable_unprepare(ctrl->aux_clk); | |
| f1: | |
| if (clk_mask & EDP_CLK_MASK_AHB) | |
| clk_disable_unprepare(ctrl->ahb_clk); | |
| f0: | |
| return ret; | |
| } | |
| static void edp_clk_disable(struct edp_ctrl *ctrl, u32 clk_mask) | |
| { | |
| if (clk_mask & EDP_CLK_MASK_MDP_CORE) | |
| clk_disable_unprepare(ctrl->mdp_core_clk); | |
| if (clk_mask & EDP_CLK_MASK_PIXEL) | |
| clk_disable_unprepare(ctrl->pixel_clk); | |
| if (clk_mask & EDP_CLK_MASK_LINK) | |
| clk_disable_unprepare(ctrl->link_clk); | |
| if (clk_mask & EDP_CLK_MASK_AUX) | |
| clk_disable_unprepare(ctrl->aux_clk); | |
| if (clk_mask & EDP_CLK_MASK_AHB) | |
| clk_disable_unprepare(ctrl->ahb_clk); | |
| } | |
| static int edp_regulator_init(struct edp_ctrl *ctrl) | |
| { | |
| struct device *dev = &ctrl->pdev->dev; | |
| int ret; | |
| DBG(""); | |
| ctrl->vdda_vreg = devm_regulator_get(dev, "vdda"); | |
| ret = PTR_ERR_OR_ZERO(ctrl->vdda_vreg); | |
| if (ret) { | |
| pr_err("%s: Could not get vdda reg, ret = %d\n", __func__, | |
| ret); | |
| ctrl->vdda_vreg = NULL; | |
| return ret; | |
| } | |
| ctrl->lvl_vreg = devm_regulator_get(dev, "lvl-vdd"); | |
| ret = PTR_ERR_OR_ZERO(ctrl->lvl_vreg); | |
| if (ret) { | |
| pr_err("%s: Could not get lvl-vdd reg, ret = %d\n", __func__, | |
| ret); | |
| ctrl->lvl_vreg = NULL; | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| static int edp_regulator_enable(struct edp_ctrl *ctrl) | |
| { | |
| int ret; | |
| ret = regulator_set_load(ctrl->vdda_vreg, VDDA_UA_ON_LOAD); | |
| if (ret < 0) { | |
| pr_err("%s: vdda_vreg set regulator mode failed.\n", __func__); | |
| goto vdda_set_fail; | |
| } | |
| ret = regulator_enable(ctrl->vdda_vreg); | |
| if (ret) { | |
| pr_err("%s: Failed to enable vdda_vreg regulator.\n", __func__); | |
| goto vdda_enable_fail; | |
| } | |
| ret = regulator_enable(ctrl->lvl_vreg); | |
| if (ret) { | |
| pr_err("Failed to enable lvl-vdd reg regulator, %d", ret); | |
| goto lvl_enable_fail; | |
| } | |
| DBG("exit"); | |
| return 0; | |
| lvl_enable_fail: | |
| regulator_disable(ctrl->vdda_vreg); | |
| vdda_enable_fail: | |
| regulator_set_load(ctrl->vdda_vreg, VDDA_UA_OFF_LOAD); | |
| vdda_set_fail: | |
| return ret; | |
| } | |
| static void edp_regulator_disable(struct edp_ctrl *ctrl) | |
| { | |
| regulator_disable(ctrl->lvl_vreg); | |
| regulator_disable(ctrl->vdda_vreg); | |
| regulator_set_load(ctrl->vdda_vreg, VDDA_UA_OFF_LOAD); | |
| } | |
| static int edp_gpio_config(struct edp_ctrl *ctrl) | |
| { | |
| struct device *dev = &ctrl->pdev->dev; | |
| int ret; | |
| ctrl->panel_hpd_gpio = devm_gpiod_get(dev, "panel-hpd", GPIOD_IN); | |
| if (IS_ERR(ctrl->panel_hpd_gpio)) { | |
| ret = PTR_ERR(ctrl->panel_hpd_gpio); | |
| ctrl->panel_hpd_gpio = NULL; | |
| pr_err("%s: cannot get panel-hpd-gpios, %d\n", __func__, ret); | |
| return ret; | |
| } | |
| ctrl->panel_en_gpio = devm_gpiod_get(dev, "panel-en", GPIOD_OUT_LOW); | |
| if (IS_ERR(ctrl->panel_en_gpio)) { | |
| ret = PTR_ERR(ctrl->panel_en_gpio); | |
| ctrl->panel_en_gpio = NULL; | |
| pr_err("%s: cannot get panel-en-gpios, %d\n", __func__, ret); | |
| return ret; | |
| } | |
| DBG("gpio on"); | |
| return 0; | |
| } | |
| static void edp_ctrl_irq_enable(struct edp_ctrl *ctrl, int enable) | |
| { | |
| unsigned long flags; | |
| DBG("%d", enable); | |
| spin_lock_irqsave(&ctrl->irq_lock, flags); | |
| if (enable) { | |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_1, EDP_INTR_MASK1); | |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_2, EDP_INTR_MASK2); | |
| } else { | |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_1, 0x0); | |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_2, 0x0); | |
| } | |
| spin_unlock_irqrestore(&ctrl->irq_lock, flags); | |
| DBG("exit"); | |
| } | |
| static void edp_fill_link_cfg(struct edp_ctrl *ctrl) | |
| { | |
| u32 prate; | |
| u32 lrate; | |
| u32 bpp; | |
| u8 max_lane = ctrl->dp_link.num_lanes; | |
| u8 lane; | |
| prate = ctrl->pixel_rate; | |
| bpp = ctrl->color_depth * 3; | |
| /* | |
| * By default, use the maximum link rate and minimum lane count, | |
| * so that we can do rate down shift during link training. | |
| */ | |
| ctrl->link_rate = drm_dp_link_rate_to_bw_code(ctrl->dp_link.rate); | |
| prate *= bpp; | |
| prate /= 8; /* in kByte */ | |
| lrate = 270000; /* in kHz */ | |
| lrate *= ctrl->link_rate; | |
| lrate /= 10; /* in kByte, 10 bits --> 8 bits */ | |
| for (lane = 1; lane <= max_lane; lane <<= 1) { | |
| if (lrate >= prate) | |
| break; | |
| lrate <<= 1; | |
| } | |
| ctrl->lane_cnt = lane; | |
| DBG("rate=%d lane=%d", ctrl->link_rate, ctrl->lane_cnt); | |
| } | |
| static void edp_config_ctrl(struct edp_ctrl *ctrl) | |
| { | |
| u32 data; | |
| enum edp_color_depth depth; | |
| data = EDP_CONFIGURATION_CTRL_LANES(ctrl->lane_cnt - 1); | |
| if (ctrl->dp_link.capabilities & DP_LINK_CAP_ENHANCED_FRAMING) | |
| data |= EDP_CONFIGURATION_CTRL_ENHANCED_FRAMING; | |
| depth = EDP_6BIT; | |
| if (ctrl->color_depth == 8) | |
| depth = EDP_8BIT; | |
| data |= EDP_CONFIGURATION_CTRL_COLOR(depth); | |
| if (!ctrl->interlaced) /* progressive */ | |
| data |= EDP_CONFIGURATION_CTRL_PROGRESSIVE; | |
| data |= (EDP_CONFIGURATION_CTRL_SYNC_CLK | | |
| EDP_CONFIGURATION_CTRL_STATIC_MVID); | |
| edp_write(ctrl->base + REG_EDP_CONFIGURATION_CTRL, data); | |
| } | |
| static void edp_state_ctrl(struct edp_ctrl *ctrl, u32 state) | |
| { | |
| edp_write(ctrl->base + REG_EDP_STATE_CTRL, state); | |
| /* Make sure H/W status is set */ | |
| wmb(); | |
| } | |
| static int edp_lane_set_write(struct edp_ctrl *ctrl, | |
| u8 voltage_level, u8 pre_emphasis_level) | |
| { | |
| int i; | |
| u8 buf[4]; | |
| if (voltage_level >= DPCD_LINK_VOLTAGE_MAX) | |
| voltage_level |= 0x04; | |
| if (pre_emphasis_level >= DPCD_LINK_PRE_EMPHASIS_MAX) | |
| pre_emphasis_level |= 0x04; | |
| pre_emphasis_level <<= 3; | |
| for (i = 0; i < 4; i++) | |
| buf[i] = voltage_level | pre_emphasis_level; | |
| DBG("%s: p|v=0x%x", __func__, voltage_level | pre_emphasis_level); | |
| if (drm_dp_dpcd_write(ctrl->drm_aux, 0x103, buf, 4) < 4) { | |
| pr_err("%s: Set sw/pe to panel failed\n", __func__); | |
| return -ENOLINK; | |
| } | |
| return 0; | |
| } | |
| static int edp_train_pattern_set_write(struct edp_ctrl *ctrl, u8 pattern) | |
| { | |
| u8 p = pattern; | |
| DBG("pattern=%x", p); | |
| if (drm_dp_dpcd_write(ctrl->drm_aux, | |
| DP_TRAINING_PATTERN_SET, &p, 1) < 1) { | |
| pr_err("%s: Set training pattern to panel failed\n", __func__); | |
| return -ENOLINK; | |
| } | |
| return 0; | |
| } | |
| static void edp_sink_train_set_adjust(struct edp_ctrl *ctrl, | |
| const u8 *link_status) | |
| { | |
| int i; | |
| u8 max = 0; | |
| u8 data; | |
| /* use the max level across lanes */ | |
| for (i = 0; i < ctrl->lane_cnt; i++) { | |
| data = drm_dp_get_adjust_request_voltage(link_status, i); | |
| DBG("lane=%d req_voltage_swing=0x%x", i, data); | |
| if (max < data) | |
| max = data; | |
| } | |
| ctrl->v_level = max >> DP_TRAIN_VOLTAGE_SWING_SHIFT; | |
| /* use the max level across lanes */ | |
| max = 0; | |
| for (i = 0; i < ctrl->lane_cnt; i++) { | |
| data = drm_dp_get_adjust_request_pre_emphasis(link_status, i); | |
| DBG("lane=%d req_pre_emphasis=0x%x", i, data); | |
| if (max < data) | |
| max = data; | |
| } | |
| ctrl->p_level = max >> DP_TRAIN_PRE_EMPHASIS_SHIFT; | |
| DBG("v_level=%d, p_level=%d", ctrl->v_level, ctrl->p_level); | |
| } | |
| static void edp_host_train_set(struct edp_ctrl *ctrl, u32 train) | |
| { | |
| int cnt = 10; | |
| u32 data; | |
| u32 shift = train - 1; | |
| DBG("train=%d", train); | |
| edp_state_ctrl(ctrl, EDP_STATE_CTRL_TRAIN_PATTERN_1 << shift); | |
| while (--cnt) { | |
| data = edp_read(ctrl->base + REG_EDP_MAINLINK_READY); | |
| if (data & (EDP_MAINLINK_READY_TRAIN_PATTERN_1_READY << shift)) | |
| break; | |
| } | |
| if (cnt == 0) | |
| pr_err("%s: set link_train=%d failed\n", __func__, train); | |
| } | |
| static const u8 vm_pre_emphasis[4][4] = { | |
| {0x03, 0x06, 0x09, 0x0C}, /* pe0, 0 db */ | |
| {0x03, 0x06, 0x09, 0xFF}, /* pe1, 3.5 db */ | |
| {0x03, 0x06, 0xFF, 0xFF}, /* pe2, 6.0 db */ | |
| {0x03, 0xFF, 0xFF, 0xFF} /* pe3, 9.5 db */ | |
| }; | |
| /* voltage swing, 0.2v and 1.0v are not support */ | |
| static const u8 vm_voltage_swing[4][4] = { | |
| {0x14, 0x18, 0x1A, 0x1E}, /* sw0, 0.4v */ | |
| {0x18, 0x1A, 0x1E, 0xFF}, /* sw1, 0.6 v */ | |
| {0x1A, 0x1E, 0xFF, 0xFF}, /* sw1, 0.8 v */ | |
| {0x1E, 0xFF, 0xFF, 0xFF} /* sw1, 1.2 v, optional */ | |
| }; | |
| static int edp_voltage_pre_emphasise_set(struct edp_ctrl *ctrl) | |
| { | |
| u32 value0; | |
| u32 value1; | |
| DBG("v=%d p=%d", ctrl->v_level, ctrl->p_level); | |
| value0 = vm_pre_emphasis[(int)(ctrl->v_level)][(int)(ctrl->p_level)]; | |
| value1 = vm_voltage_swing[(int)(ctrl->v_level)][(int)(ctrl->p_level)]; | |
| /* Configure host and panel only if both values are allowed */ | |
| if (value0 != 0xFF && value1 != 0xFF) { | |
| msm_edp_phy_vm_pe_cfg(ctrl->phy, value0, value1); | |
| return edp_lane_set_write(ctrl, ctrl->v_level, ctrl->p_level); | |
| } | |
| return -EINVAL; | |
| } | |
| static int edp_start_link_train_1(struct edp_ctrl *ctrl) | |
| { | |
| u8 link_status[DP_LINK_STATUS_SIZE]; | |
| u8 old_v_level; | |
| int tries; | |
| int ret; | |
| int rlen; | |
| DBG(""); | |
| edp_host_train_set(ctrl, DP_TRAINING_PATTERN_1); | |
| ret = edp_voltage_pre_emphasise_set(ctrl); | |
| if (ret) | |
| return ret; | |
| ret = edp_train_pattern_set_write(ctrl, | |
| DP_TRAINING_PATTERN_1 | DP_RECOVERED_CLOCK_OUT_EN); | |
| if (ret) | |
| return ret; | |
| tries = 0; | |
| old_v_level = ctrl->v_level; | |
| while (1) { | |
| drm_dp_link_train_clock_recovery_delay(ctrl->dpcd); | |
| rlen = drm_dp_dpcd_read_link_status(ctrl->drm_aux, link_status); | |
| if (rlen < DP_LINK_STATUS_SIZE) { | |
| pr_err("%s: read link status failed\n", __func__); | |
| return -ENOLINK; | |
| } | |
| if (drm_dp_clock_recovery_ok(link_status, ctrl->lane_cnt)) { | |
| ret = 0; | |
| break; | |
| } | |
| if (ctrl->v_level == DPCD_LINK_VOLTAGE_MAX) { | |
| ret = -1; | |
| break; | |
| } | |
| if (old_v_level == ctrl->v_level) { | |
| tries++; | |
| if (tries >= 5) { | |
| ret = -1; | |
| break; | |
| } | |
| } else { | |
| tries = 0; | |
| old_v_level = ctrl->v_level; | |
| } | |
| edp_sink_train_set_adjust(ctrl, link_status); | |
| ret = edp_voltage_pre_emphasise_set(ctrl); | |
| if (ret) | |
| return ret; | |
| } | |
| return ret; | |
| } | |
| static int edp_start_link_train_2(struct edp_ctrl *ctrl) | |
| { | |
| u8 link_status[DP_LINK_STATUS_SIZE]; | |
| int tries = 0; | |
| int ret; | |
| int rlen; | |
| DBG(""); | |
| edp_host_train_set(ctrl, DP_TRAINING_PATTERN_2); | |
| ret = edp_voltage_pre_emphasise_set(ctrl); | |
| if (ret) | |
| return ret; | |
| ret = edp_train_pattern_set_write(ctrl, | |
| DP_TRAINING_PATTERN_2 | DP_RECOVERED_CLOCK_OUT_EN); | |
| if (ret) | |
| return ret; | |
| while (1) { | |
| drm_dp_link_train_channel_eq_delay(ctrl->dpcd); | |
| rlen = drm_dp_dpcd_read_link_status(ctrl->drm_aux, link_status); | |
| if (rlen < DP_LINK_STATUS_SIZE) { | |
| pr_err("%s: read link status failed\n", __func__); | |
| return -ENOLINK; | |
| } | |
| if (drm_dp_channel_eq_ok(link_status, ctrl->lane_cnt)) { | |
| ret = 0; | |
| break; | |
| } | |
| tries++; | |
| if (tries > 10) { | |
| ret = -1; | |
| break; | |
| } | |
| edp_sink_train_set_adjust(ctrl, link_status); | |
| ret = edp_voltage_pre_emphasise_set(ctrl); | |
| if (ret) | |
| return ret; | |
| } | |
| return ret; | |
| } | |
| static int edp_link_rate_down_shift(struct edp_ctrl *ctrl) | |
| { | |
| u32 prate, lrate, bpp; | |
| u8 rate, lane, max_lane; | |
| int changed = 0; | |
| rate = ctrl->link_rate; | |
| lane = ctrl->lane_cnt; | |
| max_lane = ctrl->dp_link.num_lanes; | |
| bpp = ctrl->color_depth * 3; | |
| prate = ctrl->pixel_rate; | |
| prate *= bpp; | |
| prate /= 8; /* in kByte */ | |
| if (rate > DP_LINK_BW_1_62 && rate <= EDP_LINK_BW_MAX) { | |
| rate -= 4; /* reduce rate */ | |
| changed++; | |
| } | |
| if (changed) { | |
| if (lane >= 1 && lane < max_lane) | |
| lane <<= 1; /* increase lane */ | |
| lrate = 270000; /* in kHz */ | |
| lrate *= rate; | |
| lrate /= 10; /* kByte, 10 bits --> 8 bits */ | |
| lrate *= lane; | |
| DBG("new lrate=%u prate=%u(kHz) rate=%d lane=%d p=%u b=%d", | |
| lrate, prate, rate, lane, | |
| ctrl->pixel_rate, | |
| bpp); | |
| if (lrate > prate) { | |
| ctrl->link_rate = rate; | |
| ctrl->lane_cnt = lane; | |
| DBG("new rate=%d %d", rate, lane); | |
| return 0; | |
| } | |
| } | |
| return -EINVAL; | |
| } | |
| static int edp_clear_training_pattern(struct edp_ctrl *ctrl) | |
| { | |
| int ret; | |
| ret = edp_train_pattern_set_write(ctrl, 0); | |
| drm_dp_link_train_channel_eq_delay(ctrl->dpcd); | |
| return ret; | |
| } | |
| static int edp_do_link_train(struct edp_ctrl *ctrl) | |
| { | |
| int ret; | |
| struct drm_dp_link dp_link; | |
| DBG(""); | |
| /* | |
| * Set the current link rate and lane cnt to panel. They may have been | |
| * adjusted and the values are different from them in DPCD CAP | |
| */ | |
| dp_link.num_lanes = ctrl->lane_cnt; | |
| dp_link.rate = drm_dp_bw_code_to_link_rate(ctrl->link_rate); | |
| dp_link.capabilities = ctrl->dp_link.capabilities; | |
| if (drm_dp_link_configure(ctrl->drm_aux, &dp_link) < 0) | |
| return EDP_TRAIN_FAIL; | |
| ctrl->v_level = 0; /* start from default level */ | |
| ctrl->p_level = 0; | |
| edp_state_ctrl(ctrl, 0); | |
| if (edp_clear_training_pattern(ctrl)) | |
| return EDP_TRAIN_FAIL; | |
| ret = edp_start_link_train_1(ctrl); | |
| if (ret < 0) { | |
| if (edp_link_rate_down_shift(ctrl) == 0) { | |
| DBG("link reconfig"); | |
| ret = EDP_TRAIN_RECONFIG; | |
| goto clear; | |
| } else { | |
| pr_err("%s: Training 1 failed", __func__); | |
| ret = EDP_TRAIN_FAIL; | |
| goto clear; | |
| } | |
| } | |
| DBG("Training 1 completed successfully"); | |
| edp_state_ctrl(ctrl, 0); | |
| if (edp_clear_training_pattern(ctrl)) | |
| return EDP_TRAIN_FAIL; | |
| ret = edp_start_link_train_2(ctrl); | |
| if (ret < 0) { | |
| if (edp_link_rate_down_shift(ctrl) == 0) { | |
| DBG("link reconfig"); | |
| ret = EDP_TRAIN_RECONFIG; | |
| goto clear; | |
| } else { | |
| pr_err("%s: Training 2 failed", __func__); | |
| ret = EDP_TRAIN_FAIL; | |
| goto clear; | |
| } | |
| } | |
| DBG("Training 2 completed successfully"); | |
| edp_state_ctrl(ctrl, EDP_STATE_CTRL_SEND_VIDEO); | |
| clear: | |
| edp_clear_training_pattern(ctrl); | |
| return ret; | |
| } | |
| static void edp_clock_synchrous(struct edp_ctrl *ctrl, int sync) | |
| { | |
| u32 data; | |
| enum edp_color_depth depth; | |
| data = edp_read(ctrl->base + REG_EDP_MISC1_MISC0); | |
| if (sync) | |
| data |= EDP_MISC1_MISC0_SYNC; | |
| else | |
| data &= ~EDP_MISC1_MISC0_SYNC; | |
| /* only legacy rgb mode supported */ | |
| depth = EDP_6BIT; /* Default */ | |
| if (ctrl->color_depth == 8) | |
| depth = EDP_8BIT; | |
| else if (ctrl->color_depth == 10) | |
| depth = EDP_10BIT; | |
| else if (ctrl->color_depth == 12) | |
| depth = EDP_12BIT; | |
| else if (ctrl->color_depth == 16) | |
| depth = EDP_16BIT; | |
| data |= EDP_MISC1_MISC0_COLOR(depth); | |
| edp_write(ctrl->base + REG_EDP_MISC1_MISC0, data); | |
| } | |
| static int edp_sw_mvid_nvid(struct edp_ctrl *ctrl, u32 m, u32 n) | |
| { | |
| u32 n_multi, m_multi = 5; | |
| if (ctrl->link_rate == DP_LINK_BW_1_62) { | |
| n_multi = 1; | |
| } else if (ctrl->link_rate == DP_LINK_BW_2_7) { | |
| n_multi = 2; | |
| } else { | |
| pr_err("%s: Invalid link rate, %d\n", __func__, | |
| ctrl->link_rate); | |
| return -EINVAL; | |
| } | |
| edp_write(ctrl->base + REG_EDP_SOFTWARE_MVID, m * m_multi); | |
| edp_write(ctrl->base + REG_EDP_SOFTWARE_NVID, n * n_multi); | |
| return 0; | |
| } | |
| static void edp_mainlink_ctrl(struct edp_ctrl *ctrl, int enable) | |
| { | |
| u32 data = 0; | |
| edp_write(ctrl->base + REG_EDP_MAINLINK_CTRL, EDP_MAINLINK_CTRL_RESET); | |
| /* Make sure fully reset */ | |
| wmb(); | |
| usleep_range(500, 1000); | |
| if (enable) | |
| data |= EDP_MAINLINK_CTRL_ENABLE; | |
| edp_write(ctrl->base + REG_EDP_MAINLINK_CTRL, data); | |
| } | |
| static void edp_ctrl_phy_aux_enable(struct edp_ctrl *ctrl, int enable) | |
| { | |
| if (enable) { | |
| edp_regulator_enable(ctrl); | |
| edp_clk_enable(ctrl, EDP_CLK_MASK_AUX_CHAN); | |
| msm_edp_phy_ctrl(ctrl->phy, 1); | |
| msm_edp_aux_ctrl(ctrl->aux, 1); | |
| gpiod_set_value(ctrl->panel_en_gpio, 1); | |
| } else { | |
| gpiod_set_value(ctrl->panel_en_gpio, 0); | |
| msm_edp_aux_ctrl(ctrl->aux, 0); | |
| msm_edp_phy_ctrl(ctrl->phy, 0); | |
| edp_clk_disable(ctrl, EDP_CLK_MASK_AUX_CHAN); | |
| edp_regulator_disable(ctrl); | |
| } | |
| } | |
| static void edp_ctrl_link_enable(struct edp_ctrl *ctrl, int enable) | |
| { | |
| u32 m, n; | |
| if (enable) { | |
| /* Enable link channel clocks */ | |
| edp_clk_enable(ctrl, EDP_CLK_MASK_LINK_CHAN); | |
| msm_edp_phy_lane_power_ctrl(ctrl->phy, true, ctrl->lane_cnt); | |
| msm_edp_phy_vm_pe_init(ctrl->phy); | |
| /* Make sure phy is programed */ | |
| wmb(); | |
| msm_edp_phy_ready(ctrl->phy); | |
| edp_config_ctrl(ctrl); | |
| msm_edp_ctrl_pixel_clock_valid(ctrl, ctrl->pixel_rate, &m, &n); | |
| edp_sw_mvid_nvid(ctrl, m, n); | |
| edp_mainlink_ctrl(ctrl, 1); | |
| } else { | |
| edp_mainlink_ctrl(ctrl, 0); | |
| msm_edp_phy_lane_power_ctrl(ctrl->phy, false, 0); | |
| edp_clk_disable(ctrl, EDP_CLK_MASK_LINK_CHAN); | |
| } | |
| } | |
| static int edp_ctrl_training(struct edp_ctrl *ctrl) | |
| { | |
| int ret; | |
| /* Do link training only when power is on */ | |
| if (!ctrl->power_on) | |
| return -EINVAL; | |
| train_start: | |
| ret = edp_do_link_train(ctrl); | |
| if (ret == EDP_TRAIN_RECONFIG) { | |
| /* Re-configure main link */ | |
| edp_ctrl_irq_enable(ctrl, 0); | |
| edp_ctrl_link_enable(ctrl, 0); | |
| msm_edp_phy_ctrl(ctrl->phy, 0); | |
| /* Make sure link is fully disabled */ | |
| wmb(); | |
| usleep_range(500, 1000); | |
| msm_edp_phy_ctrl(ctrl->phy, 1); | |
| edp_ctrl_link_enable(ctrl, 1); | |
| edp_ctrl_irq_enable(ctrl, 1); | |
| goto train_start; | |
| } | |
| return ret; | |
| } | |
| static void edp_ctrl_on_worker(struct work_struct *work) | |
| { | |
| struct edp_ctrl *ctrl = container_of( | |
| work, struct edp_ctrl, on_work); | |
| int ret; | |
| mutex_lock(&ctrl->dev_mutex); | |
| if (ctrl->power_on) { | |
| DBG("already on"); | |
| goto unlock_ret; | |
| } | |
| edp_ctrl_phy_aux_enable(ctrl, 1); | |
| edp_ctrl_link_enable(ctrl, 1); | |
| edp_ctrl_irq_enable(ctrl, 1); | |
| ret = drm_dp_link_power_up(ctrl->drm_aux, &ctrl->dp_link); | |
| if (ret) | |
| goto fail; | |
| ctrl->power_on = true; | |
| /* Start link training */ | |
| ret = edp_ctrl_training(ctrl); | |
| if (ret != EDP_TRAIN_SUCCESS) | |
| goto fail; | |
| DBG("DONE"); | |
| goto unlock_ret; | |
| fail: | |
| edp_ctrl_irq_enable(ctrl, 0); | |
| edp_ctrl_link_enable(ctrl, 0); | |
| edp_ctrl_phy_aux_enable(ctrl, 0); | |
| ctrl->power_on = false; | |
| unlock_ret: | |
| mutex_unlock(&ctrl->dev_mutex); | |
| } | |
| static void edp_ctrl_off_worker(struct work_struct *work) | |
| { | |
| struct edp_ctrl *ctrl = container_of( | |
| work, struct edp_ctrl, off_work); | |
| unsigned long time_left; | |
| mutex_lock(&ctrl->dev_mutex); | |
| if (!ctrl->power_on) { | |
| DBG("already off"); | |
| goto unlock_ret; | |
| } | |
| reinit_completion(&ctrl->idle_comp); | |
| edp_state_ctrl(ctrl, EDP_STATE_CTRL_PUSH_IDLE); | |
| time_left = wait_for_completion_timeout(&ctrl->idle_comp, | |
| msecs_to_jiffies(500)); | |
| if (!time_left) | |
| DBG("%s: idle pattern timedout\n", __func__); | |
| edp_state_ctrl(ctrl, 0); | |
| drm_dp_link_power_down(ctrl->drm_aux, &ctrl->dp_link); | |
| edp_ctrl_irq_enable(ctrl, 0); | |
| edp_ctrl_link_enable(ctrl, 0); | |
| edp_ctrl_phy_aux_enable(ctrl, 0); | |
| ctrl->power_on = false; | |
| unlock_ret: | |
| mutex_unlock(&ctrl->dev_mutex); | |
| } | |
| irqreturn_t msm_edp_ctrl_irq(struct edp_ctrl *ctrl) | |
| { | |
| u32 isr1, isr2, mask1, mask2; | |
| u32 ack; | |
| DBG(""); | |
| spin_lock(&ctrl->irq_lock); | |
| isr1 = edp_read(ctrl->base + REG_EDP_INTERRUPT_REG_1); | |
| isr2 = edp_read(ctrl->base + REG_EDP_INTERRUPT_REG_2); | |
| mask1 = isr1 & EDP_INTR_MASK1; | |
| mask2 = isr2 & EDP_INTR_MASK2; | |
| isr1 &= ~mask1; /* remove masks bit */ | |
| isr2 &= ~mask2; | |
| DBG("isr=%x mask=%x isr2=%x mask2=%x", | |
| isr1, mask1, isr2, mask2); | |
| ack = isr1 & EDP_INTR_STATUS1; | |
| ack <<= 1; /* ack bits */ | |
| ack |= mask1; | |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_1, ack); | |
| ack = isr2 & EDP_INTR_STATUS2; | |
| ack <<= 1; /* ack bits */ | |
| ack |= mask2; | |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_2, ack); | |
| spin_unlock(&ctrl->irq_lock); | |
| if (isr1 & EDP_INTERRUPT_REG_1_HPD) | |
| DBG("edp_hpd"); | |
| if (isr2 & EDP_INTERRUPT_REG_2_READY_FOR_VIDEO) | |
| DBG("edp_video_ready"); | |
| if (isr2 & EDP_INTERRUPT_REG_2_IDLE_PATTERNs_SENT) { | |
| DBG("idle_patterns_sent"); | |
| complete(&ctrl->idle_comp); | |
| } | |
| msm_edp_aux_irq(ctrl->aux, isr1); | |
| return IRQ_HANDLED; | |
| } | |
| void msm_edp_ctrl_power(struct edp_ctrl *ctrl, bool on) | |
| { | |
| if (on) | |
| queue_work(ctrl->workqueue, &ctrl->on_work); | |
| else | |
| queue_work(ctrl->workqueue, &ctrl->off_work); | |
| } | |
| int msm_edp_ctrl_init(struct msm_edp *edp) | |
| { | |
| struct edp_ctrl *ctrl = NULL; | |
| struct device *dev = &edp->pdev->dev; | |
| int ret; | |
| if (!edp) { | |
| pr_err("%s: edp is NULL!\n", __func__); | |
| return -EINVAL; | |
| } | |
| ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL); | |
| if (!ctrl) | |
| return -ENOMEM; | |
| edp->ctrl = ctrl; | |
| ctrl->pdev = edp->pdev; | |
| ctrl->base = msm_ioremap(ctrl->pdev, "edp", "eDP"); | |
| if (IS_ERR(ctrl->base)) | |
| return PTR_ERR(ctrl->base); | |
| /* Get regulator, clock, gpio, pwm */ | |
| ret = edp_regulator_init(ctrl); | |
| if (ret) { | |
| pr_err("%s:regulator init fail\n", __func__); | |
| return ret; | |
| } | |
| ret = edp_clk_init(ctrl); | |
| if (ret) { | |
| pr_err("%s:clk init fail\n", __func__); | |
| return ret; | |
| } | |
| ret = edp_gpio_config(ctrl); | |
| if (ret) { | |
| pr_err("%s:failed to configure GPIOs: %d", __func__, ret); | |
| return ret; | |
| } | |
| /* Init aux and phy */ | |
| ctrl->aux = msm_edp_aux_init(dev, ctrl->base, &ctrl->drm_aux); | |
| if (!ctrl->aux || !ctrl->drm_aux) { | |
| pr_err("%s:failed to init aux\n", __func__); | |
| return -ENOMEM; | |
| } | |
| ctrl->phy = msm_edp_phy_init(dev, ctrl->base); | |
| if (!ctrl->phy) { | |
| pr_err("%s:failed to init phy\n", __func__); | |
| ret = -ENOMEM; | |
| goto err_destory_aux; | |
| } | |
| spin_lock_init(&ctrl->irq_lock); | |
| mutex_init(&ctrl->dev_mutex); | |
| init_completion(&ctrl->idle_comp); | |
| /* setup workqueue */ | |
| ctrl->workqueue = alloc_ordered_workqueue("edp_drm_work", 0); | |
| INIT_WORK(&ctrl->on_work, edp_ctrl_on_worker); | |
| INIT_WORK(&ctrl->off_work, edp_ctrl_off_worker); | |
| return 0; | |
| err_destory_aux: | |
| msm_edp_aux_destroy(dev, ctrl->aux); | |
| ctrl->aux = NULL; | |
| return ret; | |
| } | |
| void msm_edp_ctrl_destroy(struct edp_ctrl *ctrl) | |
| { | |
| if (!ctrl) | |
| return; | |
| if (ctrl->workqueue) { | |
| flush_workqueue(ctrl->workqueue); | |
| destroy_workqueue(ctrl->workqueue); | |
| ctrl->workqueue = NULL; | |
| } | |
| if (ctrl->aux) { | |
| msm_edp_aux_destroy(&ctrl->pdev->dev, ctrl->aux); | |
| ctrl->aux = NULL; | |
| } | |
| kfree(ctrl->edid); | |
| ctrl->edid = NULL; | |
| mutex_destroy(&ctrl->dev_mutex); | |
| } | |
| bool msm_edp_ctrl_panel_connected(struct edp_ctrl *ctrl) | |
| { | |
| mutex_lock(&ctrl->dev_mutex); | |
| DBG("connect status = %d", ctrl->edp_connected); | |
| if (ctrl->edp_connected) { | |
| mutex_unlock(&ctrl->dev_mutex); | |
| return true; | |
| } | |
| if (!ctrl->power_on) { | |
| edp_ctrl_phy_aux_enable(ctrl, 1); | |
| edp_ctrl_irq_enable(ctrl, 1); | |
| } | |
| if (drm_dp_dpcd_read(ctrl->drm_aux, DP_DPCD_REV, ctrl->dpcd, | |
| DP_RECEIVER_CAP_SIZE) < DP_RECEIVER_CAP_SIZE) { | |
| pr_err("%s: AUX channel is NOT ready\n", __func__); | |
| memset(ctrl->dpcd, 0, DP_RECEIVER_CAP_SIZE); | |
| } else { | |
| ctrl->edp_connected = true; | |
| } | |
| if (!ctrl->power_on) { | |
| edp_ctrl_irq_enable(ctrl, 0); | |
| edp_ctrl_phy_aux_enable(ctrl, 0); | |
| } | |
| DBG("exit: connect status=%d", ctrl->edp_connected); | |
| mutex_unlock(&ctrl->dev_mutex); | |
| return ctrl->edp_connected; | |
| } | |
| int msm_edp_ctrl_get_panel_info(struct edp_ctrl *ctrl, | |
| struct drm_connector *connector, struct edid **edid) | |
| { | |
| int ret = 0; | |
| mutex_lock(&ctrl->dev_mutex); | |
| if (ctrl->edid) { | |
| if (edid) { | |
| DBG("Just return edid buffer"); | |
| *edid = ctrl->edid; | |
| } | |
| goto unlock_ret; | |
| } | |
| if (!ctrl->power_on) { | |
| edp_ctrl_phy_aux_enable(ctrl, 1); | |
| edp_ctrl_irq_enable(ctrl, 1); | |
| } | |
| ret = drm_dp_link_probe(ctrl->drm_aux, &ctrl->dp_link); | |
| if (ret) { | |
| pr_err("%s: read dpcd cap failed, %d\n", __func__, ret); | |
| goto disable_ret; | |
| } | |
| /* Initialize link rate as panel max link rate */ | |
| ctrl->link_rate = drm_dp_link_rate_to_bw_code(ctrl->dp_link.rate); | |
| ctrl->edid = drm_get_edid(connector, &ctrl->drm_aux->ddc); | |
| if (!ctrl->edid) { | |
| pr_err("%s: edid read fail\n", __func__); | |
| goto disable_ret; | |
| } | |
| if (edid) | |
| *edid = ctrl->edid; | |
| disable_ret: | |
| if (!ctrl->power_on) { | |
| edp_ctrl_irq_enable(ctrl, 0); | |
| edp_ctrl_phy_aux_enable(ctrl, 0); | |
| } | |
| unlock_ret: | |
| mutex_unlock(&ctrl->dev_mutex); | |
| return ret; | |
| } | |
| int msm_edp_ctrl_timing_cfg(struct edp_ctrl *ctrl, | |
| const struct drm_display_mode *mode, | |
| const struct drm_display_info *info) | |
| { | |
| u32 hstart_from_sync, vstart_from_sync; | |
| u32 data; | |
| int ret = 0; | |
| mutex_lock(&ctrl->dev_mutex); | |
| /* | |
| * Need to keep color depth, pixel rate and | |
| * interlaced information in ctrl context | |
| */ | |
| ctrl->color_depth = info->bpc; | |
| ctrl->pixel_rate = mode->clock; | |
| ctrl->interlaced = !!(mode->flags & DRM_MODE_FLAG_INTERLACE); | |
| /* Fill initial link config based on passed in timing */ | |
| edp_fill_link_cfg(ctrl); | |
| if (edp_clk_enable(ctrl, EDP_CLK_MASK_AHB)) { | |
| pr_err("%s, fail to prepare enable ahb clk\n", __func__); | |
| ret = -EINVAL; | |
| goto unlock_ret; | |
| } | |
| edp_clock_synchrous(ctrl, 1); | |
| /* Configure eDP timing to HW */ | |
| edp_write(ctrl->base + REG_EDP_TOTAL_HOR_VER, | |
| EDP_TOTAL_HOR_VER_HORIZ(mode->htotal) | | |
| EDP_TOTAL_HOR_VER_VERT(mode->vtotal)); | |
| vstart_from_sync = mode->vtotal - mode->vsync_start; | |
| hstart_from_sync = mode->htotal - mode->hsync_start; | |
| edp_write(ctrl->base + REG_EDP_START_HOR_VER_FROM_SYNC, | |
| EDP_START_HOR_VER_FROM_SYNC_HORIZ(hstart_from_sync) | | |
| EDP_START_HOR_VER_FROM_SYNC_VERT(vstart_from_sync)); | |
| data = EDP_HSYNC_VSYNC_WIDTH_POLARITY_VERT( | |
| mode->vsync_end - mode->vsync_start); | |
| data |= EDP_HSYNC_VSYNC_WIDTH_POLARITY_HORIZ( | |
| mode->hsync_end - mode->hsync_start); | |
| if (mode->flags & DRM_MODE_FLAG_NVSYNC) | |
| data |= EDP_HSYNC_VSYNC_WIDTH_POLARITY_NVSYNC; | |
| if (mode->flags & DRM_MODE_FLAG_NHSYNC) | |
| data |= EDP_HSYNC_VSYNC_WIDTH_POLARITY_NHSYNC; | |
| edp_write(ctrl->base + REG_EDP_HSYNC_VSYNC_WIDTH_POLARITY, data); | |
| edp_write(ctrl->base + REG_EDP_ACTIVE_HOR_VER, | |
| EDP_ACTIVE_HOR_VER_HORIZ(mode->hdisplay) | | |
| EDP_ACTIVE_HOR_VER_VERT(mode->vdisplay)); | |
| edp_clk_disable(ctrl, EDP_CLK_MASK_AHB); | |
| unlock_ret: | |
| mutex_unlock(&ctrl->dev_mutex); | |
| return ret; | |
| } | |
| bool msm_edp_ctrl_pixel_clock_valid(struct edp_ctrl *ctrl, | |
| u32 pixel_rate, u32 *pm, u32 *pn) | |
| { | |
| const struct edp_pixel_clk_div *divs; | |
| u32 err = 1; /* 1% error tolerance */ | |
| u32 clk_err; | |
| int i; | |
| if (ctrl->link_rate == DP_LINK_BW_1_62) { | |
| divs = clk_divs[0]; | |
| } else if (ctrl->link_rate == DP_LINK_BW_2_7) { | |
| divs = clk_divs[1]; | |
| } else { | |
| pr_err("%s: Invalid link rate,%d\n", __func__, ctrl->link_rate); | |
| return false; | |
| } | |
| for (i = 0; i < EDP_PIXEL_CLK_NUM; i++) { | |
| clk_err = abs(divs[i].rate - pixel_rate); | |
| if ((divs[i].rate * err / 100) >= clk_err) { | |
| if (pm) | |
| *pm = divs[i].m; | |
| if (pn) | |
| *pn = divs[i].n; | |
| return true; | |
| } | |
| } | |
| DBG("pixel clock %d(kHz) not supported", pixel_rate); | |
| return false; | |
| } | |