blob: 547859c388ce4bd6179659b7c2ca6572392292df [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
/*
* Device Tree Source for the RZ/{G2L,V2L} SMARC SOM common parts
*
* Copyright (C) 2021 Renesas Electronics Corp.
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irqc-rzg2l.h>
#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
/* SW1[2] should be at position 2/OFF to enable 64 GB eMMC */
#define EMMC 1
/*
* To enable uSD card on CN3,
* SW1[2] should be at position 3/ON.
* Disable eMMC by setting "#define EMMC 0" above.
*/
#define SDHI (!EMMC)
/ {
aliases {
ethernet0 = &eth0;
ethernet1 = &eth1;
};
chosen {
bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
};
memory@48000000 {
device_type = "memory";
/* first 128MB is reserved for secure area. */
reg = <0x0 0x48000000 0x0 0x78000000>;
};
reg_1p8v: regulator-1p8v {
compatible = "regulator-fixed";
regulator-name = "fixed-1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
regulator-always-on;
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
reg_1p1v: regulator-vdd-core {
compatible = "regulator-fixed";
regulator-name = "fixed-1.1V";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-boot-on;
regulator-always-on;
};
vccq_sdhi0: regulator-vccq-sdhi0 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
states = <3300000 1>, <1800000 0>;
regulator-boot-on;
gpios = <&pinctrl RZG2L_GPIO(39, 0) GPIO_ACTIVE_HIGH>;
regulator-always-on;
};
/* 32.768kHz crystal */
x2: x2-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
};
};
&adc {
pinctrl-0 = <&adc_pins>;
pinctrl-names = "default";
status = "okay";
/delete-node/ channel@6;
/delete-node/ channel@7;
};
&eth0 {
pinctrl-0 = <&eth0_pins>;
pinctrl-names = "default";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
status = "okay";
phy0: ethernet-phy@7 {
compatible = "ethernet-phy-id0022.1640",
"ethernet-phy-ieee802.3-c22";
reg = <7>;
interrupt-parent = <&irqc>;
interrupts = <RZG2L_IRQ2 IRQ_TYPE_LEVEL_LOW>;
rxc-skew-psec = <2400>;
txc-skew-psec = <2400>;
rxdv-skew-psec = <0>;
txen-skew-psec = <0>;
rxd0-skew-psec = <0>;
rxd1-skew-psec = <0>;
rxd2-skew-psec = <0>;
rxd3-skew-psec = <0>;
txd0-skew-psec = <0>;
txd1-skew-psec = <0>;
txd2-skew-psec = <0>;
txd3-skew-psec = <0>;
};
};
&eth1 {
pinctrl-0 = <&eth1_pins>;
pinctrl-names = "default";
phy-handle = <&phy1>;
phy-mode = "rgmii-id";
status = "okay";
phy1: ethernet-phy@7 {
compatible = "ethernet-phy-id0022.1640",
"ethernet-phy-ieee802.3-c22";
reg = <7>;
interrupt-parent = <&irqc>;
interrupts = <RZG2L_IRQ3 IRQ_TYPE_LEVEL_LOW>;
rxc-skew-psec = <2400>;
txc-skew-psec = <2400>;
rxdv-skew-psec = <0>;
txen-skew-psec = <0>;
rxd0-skew-psec = <0>;
rxd1-skew-psec = <0>;
rxd2-skew-psec = <0>;
rxd3-skew-psec = <0>;
txd0-skew-psec = <0>;
txd1-skew-psec = <0>;
txd2-skew-psec = <0>;
txd3-skew-psec = <0>;
};
};
&extal_clk {
clock-frequency = <24000000>;
};
&gpu {
mali-supply = <&reg_1p1v>;
};
&i2c3 {
raa215300: pmic@12 {
compatible = "renesas,raa215300";
reg = <0x12>, <0x6f>;
reg-names = "main", "rtc";
clocks = <&x2>;
clock-names = "xin";
};
};
&ostm1 {
status = "okay";
};
&ostm2 {
status = "okay";
};
&pinctrl {
adc_pins: adc {
pinmux = <RZG2L_PORT_PINMUX(9, 0, 2)>; /* ADC_TRG */
};
eth0_pins: eth0 {
pinmux = <RZG2L_PORT_PINMUX(28, 1, 1)>, /* ET0_LINKSTA */
<RZG2L_PORT_PINMUX(27, 1, 1)>, /* ET0_MDC */
<RZG2L_PORT_PINMUX(28, 0, 1)>, /* ET0_MDIO */
<RZG2L_PORT_PINMUX(20, 0, 1)>, /* ET0_TXC */
<RZG2L_PORT_PINMUX(20, 1, 1)>, /* ET0_TX_CTL */
<RZG2L_PORT_PINMUX(20, 2, 1)>, /* ET0_TXD0 */
<RZG2L_PORT_PINMUX(21, 0, 1)>, /* ET0_TXD1 */
<RZG2L_PORT_PINMUX(21, 1, 1)>, /* ET0_TXD2 */
<RZG2L_PORT_PINMUX(22, 0, 1)>, /* ET0_TXD3 */
<RZG2L_PORT_PINMUX(24, 0, 1)>, /* ET0_RXC */
<RZG2L_PORT_PINMUX(24, 1, 1)>, /* ET0_RX_CTL */
<RZG2L_PORT_PINMUX(25, 0, 1)>, /* ET0_RXD0 */
<RZG2L_PORT_PINMUX(25, 1, 1)>, /* ET0_RXD1 */
<RZG2L_PORT_PINMUX(26, 0, 1)>, /* ET0_RXD2 */
<RZG2L_PORT_PINMUX(26, 1, 1)>, /* ET0_RXD3 */
<RZG2L_PORT_PINMUX(1, 0, 1)>; /* IRQ2 */
};
eth1_pins: eth1 {
pinmux = <RZG2L_PORT_PINMUX(37, 2, 1)>, /* ET1_LINKSTA */
<RZG2L_PORT_PINMUX(37, 0, 1)>, /* ET1_MDC */
<RZG2L_PORT_PINMUX(37, 1, 1)>, /* ET1_MDIO */
<RZG2L_PORT_PINMUX(29, 0, 1)>, /* ET1_TXC */
<RZG2L_PORT_PINMUX(29, 1, 1)>, /* ET1_TX_CTL */
<RZG2L_PORT_PINMUX(30, 0, 1)>, /* ET1_TXD0 */
<RZG2L_PORT_PINMUX(30, 1, 1)>, /* ET1_TXD1 */
<RZG2L_PORT_PINMUX(31, 0, 1)>, /* ET1_TXD2 */
<RZG2L_PORT_PINMUX(31, 1, 1)>, /* ET1_TXD3 */
<RZG2L_PORT_PINMUX(33, 1, 1)>, /* ET1_RXC */
<RZG2L_PORT_PINMUX(34, 0, 1)>, /* ET1_RX_CTL */
<RZG2L_PORT_PINMUX(34, 1, 1)>, /* ET1_RXD0 */
<RZG2L_PORT_PINMUX(35, 0, 1)>, /* ET1_RXD1 */
<RZG2L_PORT_PINMUX(35, 1, 1)>, /* ET1_RXD2 */
<RZG2L_PORT_PINMUX(36, 0, 1)>, /* ET1_RXD3 */
<RZG2L_PORT_PINMUX(1, 1, 1)>; /* IRQ3 */
};
gpio-sd0-pwr-en-hog {
gpio-hog;
gpios = <RZG2L_GPIO(4, 1) GPIO_ACTIVE_HIGH>;
output-high;
line-name = "gpio_sd0_pwr_en";
};
qspi0_pins: qspi0 {
qspi0-data {
pins = "QSPI0_IO0", "QSPI0_IO1", "QSPI0_IO2", "QSPI0_IO3";
power-source = <1800>;
};
qspi0-ctrl {
pins = "QSPI0_SPCLK", "QSPI0_SSL", "QSPI_RESET#";
power-source = <1800>;
};
};
/*
* SD0 device selection is XOR between GPIO_SD0_DEV_SEL and SW1[2]
* The below switch logic can be used to select the device between
* eMMC and microSD, after setting GPIO_SD0_DEV_SEL to high in DT.
* SW1[2] should be at position 2/OFF to enable 64 GB eMMC
* SW1[2] should be at position 3/ON to enable uSD card CN3
*/
sd0-dev-sel-hog {
gpio-hog;
gpios = <RZG2L_GPIO(41, 1) GPIO_ACTIVE_HIGH>;
output-high;
line-name = "sd0_dev_sel";
};
sdhi0_emmc_pins: sd0emmc {
sd0_emmc_data {
pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
"SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7";
power-source = <1800>;
};
sd0_emmc_ctrl {
pins = "SD0_CLK", "SD0_CMD";
power-source = <1800>;
};
sd0_emmc_rst {
pins = "SD0_RST#";
power-source = <1800>;
};
};
sdhi0_pins: sd0 {
sd0_data {
pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
power-source = <3300>;
};
sd0_ctrl {
pins = "SD0_CLK", "SD0_CMD";
power-source = <3300>;
};
sd0_mux {
pinmux = <RZG2L_PORT_PINMUX(47, 0, 2)>; /* SD0_CD */
};
};
sdhi0_pins_uhs: sd0_uhs {
sd0_data_uhs {
pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
power-source = <1800>;
};
sd0_ctrl_uhs {
pins = "SD0_CLK", "SD0_CMD";
power-source = <1800>;
};
sd0_mux_uhs {
pinmux = <RZG2L_PORT_PINMUX(47, 0, 2)>; /* SD0_CD */
};
};
};
&sbc {
pinctrl-0 = <&qspi0_pins>;
pinctrl-names = "default";
status = "okay";
flash@0 {
compatible = "micron,mt25qu512a", "jedec,spi-nor";
reg = <0>;
m25p,fast-read;
spi-max-frequency = <50000000>;
spi-rx-bus-width = <4>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
boot@0 {
reg = <0x00000000 0x2000000>;
read-only;
};
user@2000000 {
reg = <0x2000000 0x2000000>;
};
};
};
};
#if SDHI
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
pinctrl-1 = <&sdhi0_pins_uhs>;
pinctrl-names = "default", "state_uhs";
vmmc-supply = <&reg_3p3v>;
vqmmc-supply = <&vccq_sdhi0>;
bus-width = <4>;
sd-uhs-sdr50;
sd-uhs-sdr104;
status = "okay";
};
#endif
#if EMMC
&sdhi0 {
pinctrl-0 = <&sdhi0_emmc_pins>;
pinctrl-1 = <&sdhi0_emmc_pins>;
pinctrl-names = "default", "state_uhs";
vmmc-supply = <&reg_3p3v>;
vqmmc-supply = <&reg_1p8v>;
bus-width = <8>;
mmc-hs200-1_8v;
non-removable;
fixed-emmc-driver-type = <1>;
status = "okay";
};
#endif
&wdt0 {
status = "okay";
timeout-sec = <60>;
};
&wdt1 {
status = "okay";
timeout-sec = <60>;
};