| /* SPDX-License-Identifier: GPL-2.0 */ |
| /****************************************************************************** |
| * |
| * Copyright(c) 2016 Realtek Corporation. |
| * |
| * Contact Information: |
| * wlanfae <wlanfae@realtek.com> |
| * Realtek Corporation, No. 2, Innovation Road II, Hsinchu Science Park, |
| * Hsinchu 300, Taiwan. |
| * |
| * Larry Finger <Larry.Finger@lwfinger.net> |
| * |
| *****************************************************************************/ |
| #ifndef HALMAC_POWER_SEQUENCE_CMD |
| #define HALMAC_POWER_SEQUENCE_CMD |
| |
| #include "halmac_2_platform.h" |
| #include "halmac_type.h" |
| |
| #define HALMAC_POLLING_READY_TIMEOUT_COUNT 20000 |
| |
| /* The value of cmd : 4 bits */ |
| |
| /* offset : the read register offset |
| * msk : the mask of the read value |
| * value : N/A, left by 0 |
| * Note : dirver shall implement this function by read & msk |
| */ |
| #define HALMAC_PWR_CMD_READ 0x00 |
| /* |
| * offset: the read register offset |
| * msk: the mask of the write bits |
| * value: write value |
| * Note: driver shall implement this cmd by read & msk after write |
| */ |
| #define HALMAC_PWR_CMD_WRITE 0x01 |
| /* offset: the read register offset |
| * msk: the mask of the polled value |
| * value: the value to be polled, masked by the msd field. |
| * Note: driver shall implement this cmd by |
| * do{ |
| * if( (Read(offset) & msk) == (value & msk) ) |
| * break; |
| * } while(not timeout); |
| */ |
| #define HALMAC_PWR_CMD_POLLING 0x02 |
| /* offset: the value to delay |
| * msk: N/A |
| * value: the unit of delay, 0: us, 1: ms |
| */ |
| #define HALMAC_PWR_CMD_DELAY 0x03 |
| /* offset: N/A |
| * msk: N/A |
| * value: N/A |
| */ |
| #define HALMAC_PWR_CMD_END 0x04 |
| |
| /* The value of base : 4 bits */ |
| |
| /* define the base address of each block */ |
| #define HALMAC_PWR_BASEADDR_MAC 0x00 |
| #define HALMAC_PWR_BASEADDR_USB 0x01 |
| #define HALMAC_PWR_BASEADDR_PCIE 0x02 |
| #define HALMAC_PWR_BASEADDR_SDIO 0x03 |
| |
| /* The value of interface_msk : 4 bits */ |
| #define HALMAC_PWR_INTF_SDIO_MSK BIT(0) |
| #define HALMAC_PWR_INTF_USB_MSK BIT(1) |
| #define HALMAC_PWR_INTF_PCI_MSK BIT(2) |
| #define HALMAC_PWR_INTF_ALL_MSK (BIT(0) | BIT(1) | BIT(2) | BIT(3)) |
| |
| /* The value of fab_msk : 4 bits */ |
| #define HALMAC_PWR_FAB_TSMC_MSK BIT(0) |
| #define HALMAC_PWR_FAB_UMC_MSK BIT(1) |
| #define HALMAC_PWR_FAB_ALL_MSK (BIT(0) | BIT(1) | BIT(2) | BIT(3)) |
| |
| /* The value of cut_msk : 8 bits */ |
| #define HALMAC_PWR_CUT_TESTCHIP_MSK BIT(0) |
| #define HALMAC_PWR_CUT_A_MSK BIT(1) |
| #define HALMAC_PWR_CUT_B_MSK BIT(2) |
| #define HALMAC_PWR_CUT_C_MSK BIT(3) |
| #define HALMAC_PWR_CUT_D_MSK BIT(4) |
| #define HALMAC_PWR_CUT_E_MSK BIT(5) |
| #define HALMAC_PWR_CUT_F_MSK BIT(6) |
| #define HALMAC_PWR_CUT_G_MSK BIT(7) |
| #define HALMAC_PWR_CUT_ALL_MSK 0xFF |
| |
| enum halmac_pwrseq_cmd_delay_unit_ { |
| HALMAC_PWRSEQ_DELAY_US, |
| HALMAC_PWRSEQ_DELAY_MS, |
| }; |
| |
| /*Don't care endian issue, because element of pwer seq vector is fixed address*/ |
| struct halmac_wl_pwr_cfg_ { |
| u16 offset; |
| u8 cut_msk; |
| u8 fab_msk : 4; |
| u8 interface_msk : 4; |
| u8 base : 4; |
| u8 cmd : 4; |
| u8 msk; |
| u8 value; |
| }; |
| |
| #endif |