| // SPDX-License-Identifier: GPL-2.0 |
| // |
| // Copyright 2018 SiFive, Inc. |
| // |
| // SiFive SPI controller driver (master mode only) |
| // |
| // Author: SiFive, Inc. |
| // sifive@sifive.com |
| |
| #include <linux/clk.h> |
| #include <linux/module.h> |
| #include <linux/interrupt.h> |
| #include <linux/of.h> |
| #include <linux/platform_device.h> |
| #include <linux/spi/spi.h> |
| #include <linux/io.h> |
| #include <linux/log2.h> |
| |
| #define SIFIVE_SPI_DRIVER_NAME "sifive_spi" |
| |
| #define SIFIVE_SPI_MAX_CS 32 |
| #define SIFIVE_SPI_DEFAULT_DEPTH 8 |
| #define SIFIVE_SPI_DEFAULT_MAX_BITS 8 |
| |
| /* register offsets */ |
| #define SIFIVE_SPI_REG_SCKDIV 0x00 /* Serial clock divisor */ |
| #define SIFIVE_SPI_REG_SCKMODE 0x04 /* Serial clock mode */ |
| #define SIFIVE_SPI_REG_CSID 0x10 /* Chip select ID */ |
| #define SIFIVE_SPI_REG_CSDEF 0x14 /* Chip select default */ |
| #define SIFIVE_SPI_REG_CSMODE 0x18 /* Chip select mode */ |
| #define SIFIVE_SPI_REG_DELAY0 0x28 /* Delay control 0 */ |
| #define SIFIVE_SPI_REG_DELAY1 0x2c /* Delay control 1 */ |
| #define SIFIVE_SPI_REG_FMT 0x40 /* Frame format */ |
| #define SIFIVE_SPI_REG_TXDATA 0x48 /* Tx FIFO data */ |
| #define SIFIVE_SPI_REG_RXDATA 0x4c /* Rx FIFO data */ |
| #define SIFIVE_SPI_REG_TXMARK 0x50 /* Tx FIFO watermark */ |
| #define SIFIVE_SPI_REG_RXMARK 0x54 /* Rx FIFO watermark */ |
| #define SIFIVE_SPI_REG_FCTRL 0x60 /* SPI flash interface control */ |
| #define SIFIVE_SPI_REG_FFMT 0x64 /* SPI flash instruction format */ |
| #define SIFIVE_SPI_REG_IE 0x70 /* Interrupt Enable Register */ |
| #define SIFIVE_SPI_REG_IP 0x74 /* Interrupt Pendings Register */ |
| |
| /* sckdiv bits */ |
| #define SIFIVE_SPI_SCKDIV_DIV_MASK 0xfffU |
| |
| /* sckmode bits */ |
| #define SIFIVE_SPI_SCKMODE_PHA BIT(0) |
| #define SIFIVE_SPI_SCKMODE_POL BIT(1) |
| #define SIFIVE_SPI_SCKMODE_MODE_MASK (SIFIVE_SPI_SCKMODE_PHA | \ |
| SIFIVE_SPI_SCKMODE_POL) |
| |
| /* csmode bits */ |
| #define SIFIVE_SPI_CSMODE_MODE_AUTO 0U |
| #define SIFIVE_SPI_CSMODE_MODE_HOLD 2U |
| #define SIFIVE_SPI_CSMODE_MODE_OFF 3U |
| |
| /* delay0 bits */ |
| #define SIFIVE_SPI_DELAY0_CSSCK(x) ((u32)(x)) |
| #define SIFIVE_SPI_DELAY0_CSSCK_MASK 0xffU |
| #define SIFIVE_SPI_DELAY0_SCKCS(x) ((u32)(x) << 16) |
| #define SIFIVE_SPI_DELAY0_SCKCS_MASK (0xffU << 16) |
| |
| /* delay1 bits */ |
| #define SIFIVE_SPI_DELAY1_INTERCS(x) ((u32)(x)) |
| #define SIFIVE_SPI_DELAY1_INTERCS_MASK 0xffU |
| #define SIFIVE_SPI_DELAY1_INTERXFR(x) ((u32)(x) << 16) |
| #define SIFIVE_SPI_DELAY1_INTERXFR_MASK (0xffU << 16) |
| |
| /* fmt bits */ |
| #define SIFIVE_SPI_FMT_PROTO_SINGLE 0U |
| #define SIFIVE_SPI_FMT_PROTO_DUAL 1U |
| #define SIFIVE_SPI_FMT_PROTO_QUAD 2U |
| #define SIFIVE_SPI_FMT_PROTO_MASK 3U |
| #define SIFIVE_SPI_FMT_ENDIAN BIT(2) |
| #define SIFIVE_SPI_FMT_DIR BIT(3) |
| #define SIFIVE_SPI_FMT_LEN(x) ((u32)(x) << 16) |
| #define SIFIVE_SPI_FMT_LEN_MASK (0xfU << 16) |
| |
| /* txdata bits */ |
| #define SIFIVE_SPI_TXDATA_DATA_MASK 0xffU |
| #define SIFIVE_SPI_TXDATA_FULL BIT(31) |
| |
| /* rxdata bits */ |
| #define SIFIVE_SPI_RXDATA_DATA_MASK 0xffU |
| #define SIFIVE_SPI_RXDATA_EMPTY BIT(31) |
| |
| /* ie and ip bits */ |
| #define SIFIVE_SPI_IP_TXWM BIT(0) |
| #define SIFIVE_SPI_IP_RXWM BIT(1) |
| |
| struct sifive_spi { |
| void __iomem *regs; /* virt. address of control registers */ |
| struct clk *clk; /* bus clock */ |
| unsigned int fifo_depth; /* fifo depth in words */ |
| u32 cs_inactive; /* level of the CS pins when inactive */ |
| struct completion done; /* wake-up from interrupt */ |
| }; |
| |
| static void sifive_spi_write(struct sifive_spi *spi, int offset, u32 value) |
| { |
| iowrite32(value, spi->regs + offset); |
| } |
| |
| static u32 sifive_spi_read(struct sifive_spi *spi, int offset) |
| { |
| return ioread32(spi->regs + offset); |
| } |
| |
| static void sifive_spi_init(struct sifive_spi *spi) |
| { |
| /* Watermark interrupts are disabled by default */ |
| sifive_spi_write(spi, SIFIVE_SPI_REG_IE, 0); |
| |
| /* Default watermark FIFO threshold values */ |
| sifive_spi_write(spi, SIFIVE_SPI_REG_TXMARK, 1); |
| sifive_spi_write(spi, SIFIVE_SPI_REG_RXMARK, 0); |
| |
| /* Set CS/SCK Delays and Inactive Time to defaults */ |
| sifive_spi_write(spi, SIFIVE_SPI_REG_DELAY0, |
| SIFIVE_SPI_DELAY0_CSSCK(1) | |
| SIFIVE_SPI_DELAY0_SCKCS(1)); |
| sifive_spi_write(spi, SIFIVE_SPI_REG_DELAY1, |
| SIFIVE_SPI_DELAY1_INTERCS(1) | |
| SIFIVE_SPI_DELAY1_INTERXFR(0)); |
| |
| /* Exit specialized memory-mapped SPI flash mode */ |
| sifive_spi_write(spi, SIFIVE_SPI_REG_FCTRL, 0); |
| } |
| |
| static int |
| sifive_spi_prepare_message(struct spi_master *master, struct spi_message *msg) |
| { |
| struct sifive_spi *spi = spi_master_get_devdata(master); |
| struct spi_device *device = msg->spi; |
| |
| /* Update the chip select polarity */ |
| if (device->mode & SPI_CS_HIGH) |
| spi->cs_inactive &= ~BIT(device->chip_select); |
| else |
| spi->cs_inactive |= BIT(device->chip_select); |
| sifive_spi_write(spi, SIFIVE_SPI_REG_CSDEF, spi->cs_inactive); |
| |
| /* Select the correct device */ |
| sifive_spi_write(spi, SIFIVE_SPI_REG_CSID, device->chip_select); |
| |
| /* Set clock mode */ |
| sifive_spi_write(spi, SIFIVE_SPI_REG_SCKMODE, |
| device->mode & SIFIVE_SPI_SCKMODE_MODE_MASK); |
| |
| return 0; |
| } |
| |
| static void sifive_spi_set_cs(struct spi_device *device, bool is_high) |
| { |
| struct sifive_spi *spi = spi_master_get_devdata(device->master); |
| |
| /* Reverse polarity is handled by SCMR/CPOL. Not inverted CS. */ |
| if (device->mode & SPI_CS_HIGH) |
| is_high = !is_high; |
| |
| sifive_spi_write(spi, SIFIVE_SPI_REG_CSMODE, is_high ? |
| SIFIVE_SPI_CSMODE_MODE_AUTO : |
| SIFIVE_SPI_CSMODE_MODE_HOLD); |
| } |
| |
| static int |
| sifive_spi_prep_transfer(struct sifive_spi *spi, struct spi_device *device, |
| struct spi_transfer *t) |
| { |
| u32 cr; |
| unsigned int mode; |
| |
| /* Calculate and program the clock rate */ |
| cr = DIV_ROUND_UP(clk_get_rate(spi->clk) >> 1, t->speed_hz) - 1; |
| cr &= SIFIVE_SPI_SCKDIV_DIV_MASK; |
| sifive_spi_write(spi, SIFIVE_SPI_REG_SCKDIV, cr); |
| |
| mode = max_t(unsigned int, t->rx_nbits, t->tx_nbits); |
| |
| /* Set frame format */ |
| cr = SIFIVE_SPI_FMT_LEN(t->bits_per_word); |
| switch (mode) { |
| case SPI_NBITS_QUAD: |
| cr |= SIFIVE_SPI_FMT_PROTO_QUAD; |
| break; |
| case SPI_NBITS_DUAL: |
| cr |= SIFIVE_SPI_FMT_PROTO_DUAL; |
| break; |
| default: |
| cr |= SIFIVE_SPI_FMT_PROTO_SINGLE; |
| break; |
| } |
| if (device->mode & SPI_LSB_FIRST) |
| cr |= SIFIVE_SPI_FMT_ENDIAN; |
| if (!t->rx_buf) |
| cr |= SIFIVE_SPI_FMT_DIR; |
| sifive_spi_write(spi, SIFIVE_SPI_REG_FMT, cr); |
| |
| /* We will want to poll if the time we need to wait is |
| * less than the context switching time. |
| * Let's call that threshold 5us. The operation will take: |
| * (8/mode) * fifo_depth / hz <= 5 * 10^-6 |
| * 1600000 * fifo_depth <= hz * mode |
| */ |
| return 1600000 * spi->fifo_depth <= t->speed_hz * mode; |
| } |
| |
| static irqreturn_t sifive_spi_irq(int irq, void *dev_id) |
| { |
| struct sifive_spi *spi = dev_id; |
| u32 ip = sifive_spi_read(spi, SIFIVE_SPI_REG_IP); |
| |
| if (ip & (SIFIVE_SPI_IP_TXWM | SIFIVE_SPI_IP_RXWM)) { |
| /* Disable interrupts until next transfer */ |
| sifive_spi_write(spi, SIFIVE_SPI_REG_IE, 0); |
| complete(&spi->done); |
| return IRQ_HANDLED; |
| } |
| |
| return IRQ_NONE; |
| } |
| |
| static void sifive_spi_wait(struct sifive_spi *spi, u32 bit, int poll) |
| { |
| if (poll) { |
| u32 cr; |
| |
| do { |
| cr = sifive_spi_read(spi, SIFIVE_SPI_REG_IP); |
| } while (!(cr & bit)); |
| } else { |
| reinit_completion(&spi->done); |
| sifive_spi_write(spi, SIFIVE_SPI_REG_IE, bit); |
| wait_for_completion(&spi->done); |
| } |
| } |
| |
| static void sifive_spi_tx(struct sifive_spi *spi, const u8 *tx_ptr) |
| { |
| WARN_ON_ONCE((sifive_spi_read(spi, SIFIVE_SPI_REG_TXDATA) |
| & SIFIVE_SPI_TXDATA_FULL) != 0); |
| sifive_spi_write(spi, SIFIVE_SPI_REG_TXDATA, |
| *tx_ptr & SIFIVE_SPI_TXDATA_DATA_MASK); |
| } |
| |
| static void sifive_spi_rx(struct sifive_spi *spi, u8 *rx_ptr) |
| { |
| u32 data = sifive_spi_read(spi, SIFIVE_SPI_REG_RXDATA); |
| |
| WARN_ON_ONCE((data & SIFIVE_SPI_RXDATA_EMPTY) != 0); |
| *rx_ptr = data & SIFIVE_SPI_RXDATA_DATA_MASK; |
| } |
| |
| static int |
| sifive_spi_transfer_one(struct spi_master *master, struct spi_device *device, |
| struct spi_transfer *t) |
| { |
| struct sifive_spi *spi = spi_master_get_devdata(master); |
| int poll = sifive_spi_prep_transfer(spi, device, t); |
| const u8 *tx_ptr = t->tx_buf; |
| u8 *rx_ptr = t->rx_buf; |
| unsigned int remaining_words = t->len; |
| |
| while (remaining_words) { |
| unsigned int n_words = min(remaining_words, spi->fifo_depth); |
| unsigned int i; |
| |
| /* Enqueue n_words for transmission */ |
| for (i = 0; i < n_words; i++) |
| sifive_spi_tx(spi, tx_ptr++); |
| |
| if (rx_ptr) { |
| /* Wait for transmission + reception to complete */ |
| sifive_spi_write(spi, SIFIVE_SPI_REG_RXMARK, |
| n_words - 1); |
| sifive_spi_wait(spi, SIFIVE_SPI_IP_RXWM, poll); |
| |
| /* Read out all the data from the RX FIFO */ |
| for (i = 0; i < n_words; i++) |
| sifive_spi_rx(spi, rx_ptr++); |
| } else { |
| /* Wait for transmission to complete */ |
| sifive_spi_wait(spi, SIFIVE_SPI_IP_TXWM, poll); |
| } |
| |
| remaining_words -= n_words; |
| } |
| |
| return 0; |
| } |
| |
| static int sifive_spi_probe(struct platform_device *pdev) |
| { |
| struct sifive_spi *spi; |
| int ret, irq, num_cs; |
| u32 cs_bits, max_bits_per_word; |
| struct spi_master *master; |
| |
| master = spi_alloc_master(&pdev->dev, sizeof(struct sifive_spi)); |
| if (!master) { |
| dev_err(&pdev->dev, "out of memory\n"); |
| return -ENOMEM; |
| } |
| |
| spi = spi_master_get_devdata(master); |
| init_completion(&spi->done); |
| platform_set_drvdata(pdev, master); |
| |
| spi->regs = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(spi->regs)) { |
| ret = PTR_ERR(spi->regs); |
| goto put_master; |
| } |
| |
| spi->clk = devm_clk_get(&pdev->dev, NULL); |
| if (IS_ERR(spi->clk)) { |
| dev_err(&pdev->dev, "Unable to find bus clock\n"); |
| ret = PTR_ERR(spi->clk); |
| goto put_master; |
| } |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) { |
| ret = irq; |
| goto put_master; |
| } |
| |
| /* Optional parameters */ |
| ret = |
| of_property_read_u32(pdev->dev.of_node, "sifive,fifo-depth", |
| &spi->fifo_depth); |
| if (ret < 0) |
| spi->fifo_depth = SIFIVE_SPI_DEFAULT_DEPTH; |
| |
| ret = |
| of_property_read_u32(pdev->dev.of_node, "sifive,max-bits-per-word", |
| &max_bits_per_word); |
| |
| if (!ret && max_bits_per_word < 8) { |
| dev_err(&pdev->dev, "Only 8bit SPI words supported by the driver\n"); |
| ret = -EINVAL; |
| goto put_master; |
| } |
| |
| /* Spin up the bus clock before hitting registers */ |
| ret = clk_prepare_enable(spi->clk); |
| if (ret) { |
| dev_err(&pdev->dev, "Unable to enable bus clock\n"); |
| goto put_master; |
| } |
| |
| /* probe the number of CS lines */ |
| spi->cs_inactive = sifive_spi_read(spi, SIFIVE_SPI_REG_CSDEF); |
| sifive_spi_write(spi, SIFIVE_SPI_REG_CSDEF, 0xffffffffU); |
| cs_bits = sifive_spi_read(spi, SIFIVE_SPI_REG_CSDEF); |
| sifive_spi_write(spi, SIFIVE_SPI_REG_CSDEF, spi->cs_inactive); |
| if (!cs_bits) { |
| dev_err(&pdev->dev, "Could not auto probe CS lines\n"); |
| ret = -EINVAL; |
| goto disable_clk; |
| } |
| |
| num_cs = ilog2(cs_bits) + 1; |
| if (num_cs > SIFIVE_SPI_MAX_CS) { |
| dev_err(&pdev->dev, "Invalid number of spi slaves\n"); |
| ret = -EINVAL; |
| goto disable_clk; |
| } |
| |
| /* Define our master */ |
| master->dev.of_node = pdev->dev.of_node; |
| master->bus_num = pdev->id; |
| master->num_chipselect = num_cs; |
| master->mode_bits = SPI_CPHA | SPI_CPOL |
| | SPI_CS_HIGH | SPI_LSB_FIRST |
| | SPI_TX_DUAL | SPI_TX_QUAD |
| | SPI_RX_DUAL | SPI_RX_QUAD; |
| /* TODO: add driver support for bits_per_word < 8 |
| * we need to "left-align" the bits (unless SPI_LSB_FIRST) |
| */ |
| master->bits_per_word_mask = SPI_BPW_MASK(8); |
| master->flags = SPI_CONTROLLER_MUST_TX | SPI_MASTER_GPIO_SS; |
| master->prepare_message = sifive_spi_prepare_message; |
| master->set_cs = sifive_spi_set_cs; |
| master->transfer_one = sifive_spi_transfer_one; |
| |
| pdev->dev.dma_mask = NULL; |
| /* Configure the SPI master hardware */ |
| sifive_spi_init(spi); |
| |
| /* Register for SPI Interrupt */ |
| ret = devm_request_irq(&pdev->dev, irq, sifive_spi_irq, 0, |
| dev_name(&pdev->dev), spi); |
| if (ret) { |
| dev_err(&pdev->dev, "Unable to bind to interrupt\n"); |
| goto disable_clk; |
| } |
| |
| dev_info(&pdev->dev, "mapped; irq=%d, cs=%d\n", |
| irq, master->num_chipselect); |
| |
| ret = devm_spi_register_master(&pdev->dev, master); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "spi_register_master failed\n"); |
| goto disable_clk; |
| } |
| |
| return 0; |
| |
| disable_clk: |
| clk_disable_unprepare(spi->clk); |
| put_master: |
| spi_master_put(master); |
| |
| return ret; |
| } |
| |
| static int sifive_spi_remove(struct platform_device *pdev) |
| { |
| struct spi_master *master = platform_get_drvdata(pdev); |
| struct sifive_spi *spi = spi_master_get_devdata(master); |
| |
| /* Disable all the interrupts just in case */ |
| sifive_spi_write(spi, SIFIVE_SPI_REG_IE, 0); |
| clk_disable_unprepare(spi->clk); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id sifive_spi_of_match[] = { |
| { .compatible = "sifive,spi0", }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(of, sifive_spi_of_match); |
| |
| static struct platform_driver sifive_spi_driver = { |
| .probe = sifive_spi_probe, |
| .remove = sifive_spi_remove, |
| .driver = { |
| .name = SIFIVE_SPI_DRIVER_NAME, |
| .of_match_table = sifive_spi_of_match, |
| }, |
| }; |
| module_platform_driver(sifive_spi_driver); |
| |
| MODULE_AUTHOR("SiFive, Inc. <sifive@sifive.com>"); |
| MODULE_DESCRIPTION("SiFive SPI driver"); |
| MODULE_LICENSE("GPL"); |