| /* |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| /dts-v1/; |
| |
| #include "dm814x.dtsi" |
| |
| / { |
| model = "HP t410 Smart Zero Client"; |
| compatible = "hp,t410", "ti,dm8148", "ti,dm814"; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x80000000 0x40000000>; /* 1 GB */ |
| }; |
| |
| /* gpio9 seems to control USB VBUS regulator and/or hub power */ |
| usb_power: regulator@9 { |
| compatible = "regulator-fixed"; |
| regulator-name = "usb_power"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| regulator-always-on; |
| }; |
| |
| vmmcsd_fixed: fixedregulator0 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vmmcsd_fixed"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| }; |
| |
| &cpsw_emac0 { |
| phy_id = <&davinci_mdio>, <0>; |
| phy-mode = "rgmii"; |
| }; |
| |
| &cpsw_emac1 { |
| phy_id = <&davinci_mdio>, <1>; |
| phy-mode = "rgmii"; |
| }; |
| |
| &mmc1 { |
| status = "disabled"; |
| }; |
| |
| &mmc2 { |
| status = "disabled"; |
| }; |
| |
| &mmc3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sd2_pins>; |
| vmmc-supply = <&vmmcsd_fixed>; |
| bus-width = <8>; |
| dmas = <&edma_xbar 8 0 1 /* use SDTXEVT1 instead of MCASP0TX */ |
| &edma_xbar 9 0 2>; /* use SDRXEVT1 instead of MCASP0RX */ |
| dma-names = "tx", "rx"; |
| non-removable; |
| }; |
| |
| &pincntl { |
| sd2_pins: pinmux_sd2_pins { |
| pinctrl-single,pins = < |
| DM814X_IOPAD(0x09c0, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[7] */ |
| DM814X_IOPAD(0x09c4, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[6] */ |
| DM814X_IOPAD(0x09c8, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[5] */ |
| DM814X_IOPAD(0x09cc, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[4] */ |
| DM814X_IOPAD(0x09d0, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[3] */ |
| DM814X_IOPAD(0x09d4, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[2] */ |
| DM814X_IOPAD(0x09d8, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[1] */ |
| DM814X_IOPAD(0x09dc, PIN_INPUT_PULLUP | 0x1) /* SD2_DAT[0] */ |
| DM814X_IOPAD(0x09e0, PIN_INPUT | 0x1) /* SD2_CLK */ |
| DM814X_IOPAD(0x09f4, PIN_INPUT_PULLUP | 0x2) /* SD2_CMD */ |
| DM814X_IOPAD(0x0920, PIN_INPUT | 0x40) /* SD2_SDCD */ |
| >; |
| }; |
| |
| usb0_pins: pinmux_usb0_pins { |
| pinctrl-single,pins = < |
| DM814X_IOPAD(0x0c34, PIN_OUTPUT | 0x1) /* USB0_DRVVBUS */ |
| >; |
| }; |
| |
| usb1_pins: pinmux_usb1_pins { |
| pinctrl-single,pins = < |
| DM814X_IOPAD(0x0834, PIN_OUTPUT | 0x80) /* USB1_DRVVBUS */ |
| >; |
| }; |
| }; |
| |
| &usb0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb0_pins>; |
| dr_mode = "host"; |
| }; |
| |
| &usb1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb1_pins>; |
| dr_mode = "host"; |
| }; |
