| /* | |
| * MFD driver for TWL6040 audio device | |
| * | |
| * Authors: Misael Lopez Cruz <misael.lopez@ti.com> | |
| * Jorge Eduardo Candelaria <jorge.candelaria@ti.com> | |
| * Peter Ujfalusi <peter.ujfalusi@ti.com> | |
| * | |
| * Copyright: (C) 2011 Texas Instruments, Inc. | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 as | |
| * published by the Free Software Foundation. | |
| * | |
| * This program is distributed in the hope that it will be useful, but | |
| * WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU | |
| * General Public License for more details. | |
| * | |
| * You should have received a copy of the GNU General Public License | |
| * along with this program; if not, write to the Free Software | |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA | |
| * 02110-1301 USA | |
| * | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/types.h> | |
| #include <linux/slab.h> | |
| #include <linux/kernel.h> | |
| #include <linux/err.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/of.h> | |
| #include <linux/of_irq.h> | |
| #include <linux/of_gpio.h> | |
| #include <linux/of_platform.h> | |
| #include <linux/gpio.h> | |
| #include <linux/delay.h> | |
| #include <linux/i2c.h> | |
| #include <linux/regmap.h> | |
| #include <linux/mfd/core.h> | |
| #include <linux/mfd/twl6040.h> | |
| #include <linux/regulator/consumer.h> | |
| #define VIBRACTRL_MEMBER(reg) ((reg == TWL6040_REG_VIBCTLL) ? 0 : 1) | |
| #define TWL6040_NUM_SUPPLIES (2) | |
| static const struct reg_default twl6040_defaults[] = { | |
| { 0x01, 0x4B }, /* REG_ASICID (ro) */ | |
| { 0x02, 0x00 }, /* REG_ASICREV (ro) */ | |
| { 0x03, 0x00 }, /* REG_INTID */ | |
| { 0x04, 0x00 }, /* REG_INTMR */ | |
| { 0x05, 0x00 }, /* REG_NCPCTRL */ | |
| { 0x06, 0x00 }, /* REG_LDOCTL */ | |
| { 0x07, 0x60 }, /* REG_HPPLLCTL */ | |
| { 0x08, 0x00 }, /* REG_LPPLLCTL */ | |
| { 0x09, 0x4A }, /* REG_LPPLLDIV */ | |
| { 0x0A, 0x00 }, /* REG_AMICBCTL */ | |
| { 0x0B, 0x00 }, /* REG_DMICBCTL */ | |
| { 0x0C, 0x00 }, /* REG_MICLCTL */ | |
| { 0x0D, 0x00 }, /* REG_MICRCTL */ | |
| { 0x0E, 0x00 }, /* REG_MICGAIN */ | |
| { 0x0F, 0x1B }, /* REG_LINEGAIN */ | |
| { 0x10, 0x00 }, /* REG_HSLCTL */ | |
| { 0x11, 0x00 }, /* REG_HSRCTL */ | |
| { 0x12, 0x00 }, /* REG_HSGAIN */ | |
| { 0x13, 0x00 }, /* REG_EARCTL */ | |
| { 0x14, 0x00 }, /* REG_HFLCTL */ | |
| { 0x15, 0x00 }, /* REG_HFLGAIN */ | |
| { 0x16, 0x00 }, /* REG_HFRCTL */ | |
| { 0x17, 0x00 }, /* REG_HFRGAIN */ | |
| { 0x18, 0x00 }, /* REG_VIBCTLL */ | |
| { 0x19, 0x00 }, /* REG_VIBDATL */ | |
| { 0x1A, 0x00 }, /* REG_VIBCTLR */ | |
| { 0x1B, 0x00 }, /* REG_VIBDATR */ | |
| { 0x1C, 0x00 }, /* REG_HKCTL1 */ | |
| { 0x1D, 0x00 }, /* REG_HKCTL2 */ | |
| { 0x1E, 0x00 }, /* REG_GPOCTL */ | |
| { 0x1F, 0x00 }, /* REG_ALB */ | |
| { 0x20, 0x00 }, /* REG_DLB */ | |
| /* 0x28, REG_TRIM1 */ | |
| /* 0x29, REG_TRIM2 */ | |
| /* 0x2A, REG_TRIM3 */ | |
| /* 0x2B, REG_HSOTRIM */ | |
| /* 0x2C, REG_HFOTRIM */ | |
| { 0x2D, 0x08 }, /* REG_ACCCTL */ | |
| { 0x2E, 0x00 }, /* REG_STATUS (ro) */ | |
| }; | |
| static struct reg_sequence twl6040_patch[] = { | |
| /* | |
| * Select I2C bus access to dual access registers | |
| * Interrupt register is cleared on read | |
| * Select fast mode for i2c (400KHz) | |
| */ | |
| { TWL6040_REG_ACCCTL, | |
| TWL6040_I2CSEL | TWL6040_INTCLRMODE | TWL6040_I2CMODE(1) }, | |
| }; | |
| static bool twl6040_has_vibra(struct device_node *parent) | |
| { | |
| struct device_node *node; | |
| node = of_get_child_by_name(parent, "vibra"); | |
| if (node) { | |
| of_node_put(node); | |
| return true; | |
| } | |
| return false; | |
| } | |
| int twl6040_reg_read(struct twl6040 *twl6040, unsigned int reg) | |
| { | |
| int ret; | |
| unsigned int val; | |
| ret = regmap_read(twl6040->regmap, reg, &val); | |
| if (ret < 0) | |
| return ret; | |
| return val; | |
| } | |
| EXPORT_SYMBOL(twl6040_reg_read); | |
| int twl6040_reg_write(struct twl6040 *twl6040, unsigned int reg, u8 val) | |
| { | |
| int ret; | |
| ret = regmap_write(twl6040->regmap, reg, val); | |
| return ret; | |
| } | |
| EXPORT_SYMBOL(twl6040_reg_write); | |
| int twl6040_set_bits(struct twl6040 *twl6040, unsigned int reg, u8 mask) | |
| { | |
| return regmap_update_bits(twl6040->regmap, reg, mask, mask); | |
| } | |
| EXPORT_SYMBOL(twl6040_set_bits); | |
| int twl6040_clear_bits(struct twl6040 *twl6040, unsigned int reg, u8 mask) | |
| { | |
| return regmap_update_bits(twl6040->regmap, reg, mask, 0); | |
| } | |
| EXPORT_SYMBOL(twl6040_clear_bits); | |
| /* twl6040 codec manual power-up sequence */ | |
| static int twl6040_power_up_manual(struct twl6040 *twl6040) | |
| { | |
| u8 ldoctl, ncpctl, lppllctl; | |
| int ret; | |
| /* enable high-side LDO, reference system and internal oscillator */ | |
| ldoctl = TWL6040_HSLDOENA | TWL6040_REFENA | TWL6040_OSCENA; | |
| ret = twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); | |
| if (ret) | |
| return ret; | |
| usleep_range(10000, 10500); | |
| /* enable negative charge pump */ | |
| ncpctl = TWL6040_NCPENA; | |
| ret = twl6040_reg_write(twl6040, TWL6040_REG_NCPCTL, ncpctl); | |
| if (ret) | |
| goto ncp_err; | |
| usleep_range(1000, 1500); | |
| /* enable low-side LDO */ | |
| ldoctl |= TWL6040_LSLDOENA; | |
| ret = twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); | |
| if (ret) | |
| goto lsldo_err; | |
| usleep_range(1000, 1500); | |
| /* enable low-power PLL */ | |
| lppllctl = TWL6040_LPLLENA; | |
| ret = twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl); | |
| if (ret) | |
| goto lppll_err; | |
| usleep_range(5000, 5500); | |
| /* disable internal oscillator */ | |
| ldoctl &= ~TWL6040_OSCENA; | |
| ret = twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); | |
| if (ret) | |
| goto osc_err; | |
| return 0; | |
| osc_err: | |
| lppllctl &= ~TWL6040_LPLLENA; | |
| twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl); | |
| lppll_err: | |
| ldoctl &= ~TWL6040_LSLDOENA; | |
| twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); | |
| lsldo_err: | |
| ncpctl &= ~TWL6040_NCPENA; | |
| twl6040_reg_write(twl6040, TWL6040_REG_NCPCTL, ncpctl); | |
| ncp_err: | |
| ldoctl &= ~(TWL6040_HSLDOENA | TWL6040_REFENA | TWL6040_OSCENA); | |
| twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); | |
| dev_err(twl6040->dev, "manual power-up failed\n"); | |
| return ret; | |
| } | |
| /* twl6040 manual power-down sequence */ | |
| static void twl6040_power_down_manual(struct twl6040 *twl6040) | |
| { | |
| u8 ncpctl, ldoctl, lppllctl; | |
| ncpctl = twl6040_reg_read(twl6040, TWL6040_REG_NCPCTL); | |
| ldoctl = twl6040_reg_read(twl6040, TWL6040_REG_LDOCTL); | |
| lppllctl = twl6040_reg_read(twl6040, TWL6040_REG_LPPLLCTL); | |
| /* enable internal oscillator */ | |
| ldoctl |= TWL6040_OSCENA; | |
| twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); | |
| usleep_range(1000, 1500); | |
| /* disable low-power PLL */ | |
| lppllctl &= ~TWL6040_LPLLENA; | |
| twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, lppllctl); | |
| /* disable low-side LDO */ | |
| ldoctl &= ~TWL6040_LSLDOENA; | |
| twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); | |
| /* disable negative charge pump */ | |
| ncpctl &= ~TWL6040_NCPENA; | |
| twl6040_reg_write(twl6040, TWL6040_REG_NCPCTL, ncpctl); | |
| /* disable high-side LDO, reference system and internal oscillator */ | |
| ldoctl &= ~(TWL6040_HSLDOENA | TWL6040_REFENA | TWL6040_OSCENA); | |
| twl6040_reg_write(twl6040, TWL6040_REG_LDOCTL, ldoctl); | |
| } | |
| static irqreturn_t twl6040_readyint_handler(int irq, void *data) | |
| { | |
| struct twl6040 *twl6040 = data; | |
| complete(&twl6040->ready); | |
| return IRQ_HANDLED; | |
| } | |
| static irqreturn_t twl6040_thint_handler(int irq, void *data) | |
| { | |
| struct twl6040 *twl6040 = data; | |
| u8 status; | |
| status = twl6040_reg_read(twl6040, TWL6040_REG_STATUS); | |
| if (status & TWL6040_TSHUTDET) { | |
| dev_warn(twl6040->dev, "Thermal shutdown, powering-off"); | |
| twl6040_power(twl6040, 0); | |
| } else { | |
| dev_warn(twl6040->dev, "Leaving thermal shutdown, powering-on"); | |
| twl6040_power(twl6040, 1); | |
| } | |
| return IRQ_HANDLED; | |
| } | |
| static int twl6040_power_up_automatic(struct twl6040 *twl6040) | |
| { | |
| int time_left; | |
| gpio_set_value(twl6040->audpwron, 1); | |
| time_left = wait_for_completion_timeout(&twl6040->ready, | |
| msecs_to_jiffies(144)); | |
| if (!time_left) { | |
| u8 intid; | |
| dev_warn(twl6040->dev, "timeout waiting for READYINT\n"); | |
| intid = twl6040_reg_read(twl6040, TWL6040_REG_INTID); | |
| if (!(intid & TWL6040_READYINT)) { | |
| dev_err(twl6040->dev, "automatic power-up failed\n"); | |
| gpio_set_value(twl6040->audpwron, 0); | |
| return -ETIMEDOUT; | |
| } | |
| } | |
| return 0; | |
| } | |
| int twl6040_power(struct twl6040 *twl6040, int on) | |
| { | |
| int ret = 0; | |
| mutex_lock(&twl6040->mutex); | |
| if (on) { | |
| /* already powered-up */ | |
| if (twl6040->power_count++) | |
| goto out; | |
| ret = clk_prepare_enable(twl6040->clk32k); | |
| if (ret) { | |
| twl6040->power_count = 0; | |
| goto out; | |
| } | |
| /* Allow writes to the chip */ | |
| regcache_cache_only(twl6040->regmap, false); | |
| if (gpio_is_valid(twl6040->audpwron)) { | |
| /* use automatic power-up sequence */ | |
| ret = twl6040_power_up_automatic(twl6040); | |
| if (ret) { | |
| clk_disable_unprepare(twl6040->clk32k); | |
| twl6040->power_count = 0; | |
| goto out; | |
| } | |
| } else { | |
| /* use manual power-up sequence */ | |
| ret = twl6040_power_up_manual(twl6040); | |
| if (ret) { | |
| clk_disable_unprepare(twl6040->clk32k); | |
| twl6040->power_count = 0; | |
| goto out; | |
| } | |
| } | |
| /* Sync with the HW */ | |
| regcache_sync(twl6040->regmap); | |
| /* Default PLL configuration after power up */ | |
| twl6040->pll = TWL6040_SYSCLK_SEL_LPPLL; | |
| twl6040->sysclk_rate = 19200000; | |
| } else { | |
| /* already powered-down */ | |
| if (!twl6040->power_count) { | |
| dev_err(twl6040->dev, | |
| "device is already powered-off\n"); | |
| ret = -EPERM; | |
| goto out; | |
| } | |
| if (--twl6040->power_count) | |
| goto out; | |
| if (gpio_is_valid(twl6040->audpwron)) { | |
| /* use AUDPWRON line */ | |
| gpio_set_value(twl6040->audpwron, 0); | |
| /* power-down sequence latency */ | |
| usleep_range(500, 700); | |
| } else { | |
| /* use manual power-down sequence */ | |
| twl6040_power_down_manual(twl6040); | |
| } | |
| /* Set regmap to cache only and mark it as dirty */ | |
| regcache_cache_only(twl6040->regmap, true); | |
| regcache_mark_dirty(twl6040->regmap); | |
| twl6040->sysclk_rate = 0; | |
| if (twl6040->pll == TWL6040_SYSCLK_SEL_HPPLL) { | |
| clk_disable_unprepare(twl6040->mclk); | |
| twl6040->mclk_rate = 0; | |
| } | |
| clk_disable_unprepare(twl6040->clk32k); | |
| } | |
| out: | |
| mutex_unlock(&twl6040->mutex); | |
| return ret; | |
| } | |
| EXPORT_SYMBOL(twl6040_power); | |
| int twl6040_set_pll(struct twl6040 *twl6040, int pll_id, | |
| unsigned int freq_in, unsigned int freq_out) | |
| { | |
| u8 hppllctl, lppllctl; | |
| int ret = 0; | |
| mutex_lock(&twl6040->mutex); | |
| hppllctl = twl6040_reg_read(twl6040, TWL6040_REG_HPPLLCTL); | |
| lppllctl = twl6040_reg_read(twl6040, TWL6040_REG_LPPLLCTL); | |
| /* Force full reconfiguration when switching between PLL */ | |
| if (pll_id != twl6040->pll) { | |
| twl6040->sysclk_rate = 0; | |
| twl6040->mclk_rate = 0; | |
| } | |
| switch (pll_id) { | |
| case TWL6040_SYSCLK_SEL_LPPLL: | |
| /* low-power PLL divider */ | |
| /* Change the sysclk configuration only if it has been canged */ | |
| if (twl6040->sysclk_rate != freq_out) { | |
| switch (freq_out) { | |
| case 17640000: | |
| lppllctl |= TWL6040_LPLLFIN; | |
| break; | |
| case 19200000: | |
| lppllctl &= ~TWL6040_LPLLFIN; | |
| break; | |
| default: | |
| dev_err(twl6040->dev, | |
| "freq_out %d not supported\n", | |
| freq_out); | |
| ret = -EINVAL; | |
| goto pll_out; | |
| } | |
| twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, | |
| lppllctl); | |
| } | |
| /* The PLL in use has not been change, we can exit */ | |
| if (twl6040->pll == pll_id) | |
| break; | |
| switch (freq_in) { | |
| case 32768: | |
| lppllctl |= TWL6040_LPLLENA; | |
| twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, | |
| lppllctl); | |
| mdelay(5); | |
| lppllctl &= ~TWL6040_HPLLSEL; | |
| twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, | |
| lppllctl); | |
| hppllctl &= ~TWL6040_HPLLENA; | |
| twl6040_reg_write(twl6040, TWL6040_REG_HPPLLCTL, | |
| hppllctl); | |
| break; | |
| default: | |
| dev_err(twl6040->dev, | |
| "freq_in %d not supported\n", freq_in); | |
| ret = -EINVAL; | |
| goto pll_out; | |
| } | |
| clk_disable_unprepare(twl6040->mclk); | |
| break; | |
| case TWL6040_SYSCLK_SEL_HPPLL: | |
| /* high-performance PLL can provide only 19.2 MHz */ | |
| if (freq_out != 19200000) { | |
| dev_err(twl6040->dev, | |
| "freq_out %d not supported\n", freq_out); | |
| ret = -EINVAL; | |
| goto pll_out; | |
| } | |
| if (twl6040->mclk_rate != freq_in) { | |
| hppllctl &= ~TWL6040_MCLK_MSK; | |
| switch (freq_in) { | |
| case 12000000: | |
| /* PLL enabled, active mode */ | |
| hppllctl |= TWL6040_MCLK_12000KHZ | | |
| TWL6040_HPLLENA; | |
| break; | |
| case 19200000: | |
| /* PLL enabled, bypass mode */ | |
| hppllctl |= TWL6040_MCLK_19200KHZ | | |
| TWL6040_HPLLBP | TWL6040_HPLLENA; | |
| break; | |
| case 26000000: | |
| /* PLL enabled, active mode */ | |
| hppllctl |= TWL6040_MCLK_26000KHZ | | |
| TWL6040_HPLLENA; | |
| break; | |
| case 38400000: | |
| /* PLL enabled, bypass mode */ | |
| hppllctl |= TWL6040_MCLK_38400KHZ | | |
| TWL6040_HPLLBP | TWL6040_HPLLENA; | |
| break; | |
| default: | |
| dev_err(twl6040->dev, | |
| "freq_in %d not supported\n", freq_in); | |
| ret = -EINVAL; | |
| goto pll_out; | |
| } | |
| /* When switching to HPPLL, enable the mclk first */ | |
| if (pll_id != twl6040->pll) | |
| clk_prepare_enable(twl6040->mclk); | |
| /* | |
| * enable clock slicer to ensure input waveform is | |
| * square | |
| */ | |
| hppllctl |= TWL6040_HPLLSQRENA; | |
| twl6040_reg_write(twl6040, TWL6040_REG_HPPLLCTL, | |
| hppllctl); | |
| usleep_range(500, 700); | |
| lppllctl |= TWL6040_HPLLSEL; | |
| twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, | |
| lppllctl); | |
| lppllctl &= ~TWL6040_LPLLENA; | |
| twl6040_reg_write(twl6040, TWL6040_REG_LPPLLCTL, | |
| lppllctl); | |
| twl6040->mclk_rate = freq_in; | |
| } | |
| break; | |
| default: | |
| dev_err(twl6040->dev, "unknown pll id %d\n", pll_id); | |
| ret = -EINVAL; | |
| goto pll_out; | |
| } | |
| twl6040->sysclk_rate = freq_out; | |
| twl6040->pll = pll_id; | |
| pll_out: | |
| mutex_unlock(&twl6040->mutex); | |
| return ret; | |
| } | |
| EXPORT_SYMBOL(twl6040_set_pll); | |
| int twl6040_get_pll(struct twl6040 *twl6040) | |
| { | |
| if (twl6040->power_count) | |
| return twl6040->pll; | |
| else | |
| return -ENODEV; | |
| } | |
| EXPORT_SYMBOL(twl6040_get_pll); | |
| unsigned int twl6040_get_sysclk(struct twl6040 *twl6040) | |
| { | |
| return twl6040->sysclk_rate; | |
| } | |
| EXPORT_SYMBOL(twl6040_get_sysclk); | |
| /* Get the combined status of the vibra control register */ | |
| int twl6040_get_vibralr_status(struct twl6040 *twl6040) | |
| { | |
| unsigned int reg; | |
| int ret; | |
| u8 status; | |
| ret = regmap_read(twl6040->regmap, TWL6040_REG_VIBCTLL, ®); | |
| if (ret != 0) | |
| return ret; | |
| status = reg; | |
| ret = regmap_read(twl6040->regmap, TWL6040_REG_VIBCTLR, ®); | |
| if (ret != 0) | |
| return ret; | |
| status |= reg; | |
| status &= (TWL6040_VIBENA | TWL6040_VIBSEL); | |
| return status; | |
| } | |
| EXPORT_SYMBOL(twl6040_get_vibralr_status); | |
| static struct resource twl6040_vibra_rsrc[] = { | |
| { | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| }; | |
| static struct resource twl6040_codec_rsrc[] = { | |
| { | |
| .flags = IORESOURCE_IRQ, | |
| }, | |
| }; | |
| static bool twl6040_readable_reg(struct device *dev, unsigned int reg) | |
| { | |
| /* Register 0 is not readable */ | |
| if (!reg) | |
| return false; | |
| return true; | |
| } | |
| static bool twl6040_volatile_reg(struct device *dev, unsigned int reg) | |
| { | |
| switch (reg) { | |
| case TWL6040_REG_ASICID: | |
| case TWL6040_REG_ASICREV: | |
| case TWL6040_REG_INTID: | |
| case TWL6040_REG_LPPLLCTL: | |
| case TWL6040_REG_HPPLLCTL: | |
| case TWL6040_REG_STATUS: | |
| return true; | |
| default: | |
| return false; | |
| } | |
| } | |
| static bool twl6040_writeable_reg(struct device *dev, unsigned int reg) | |
| { | |
| switch (reg) { | |
| case TWL6040_REG_ASICID: | |
| case TWL6040_REG_ASICREV: | |
| case TWL6040_REG_STATUS: | |
| return false; | |
| default: | |
| return true; | |
| } | |
| } | |
| static const struct regmap_config twl6040_regmap_config = { | |
| .reg_bits = 8, | |
| .val_bits = 8, | |
| .reg_defaults = twl6040_defaults, | |
| .num_reg_defaults = ARRAY_SIZE(twl6040_defaults), | |
| .max_register = TWL6040_REG_STATUS, /* 0x2e */ | |
| .readable_reg = twl6040_readable_reg, | |
| .volatile_reg = twl6040_volatile_reg, | |
| .writeable_reg = twl6040_writeable_reg, | |
| .cache_type = REGCACHE_RBTREE, | |
| .use_single_rw = true, | |
| }; | |
| static const struct regmap_irq twl6040_irqs[] = { | |
| { .reg_offset = 0, .mask = TWL6040_THINT, }, | |
| { .reg_offset = 0, .mask = TWL6040_PLUGINT | TWL6040_UNPLUGINT, }, | |
| { .reg_offset = 0, .mask = TWL6040_HOOKINT, }, | |
| { .reg_offset = 0, .mask = TWL6040_HFINT, }, | |
| { .reg_offset = 0, .mask = TWL6040_VIBINT, }, | |
| { .reg_offset = 0, .mask = TWL6040_READYINT, }, | |
| }; | |
| static struct regmap_irq_chip twl6040_irq_chip = { | |
| .name = "twl6040", | |
| .irqs = twl6040_irqs, | |
| .num_irqs = ARRAY_SIZE(twl6040_irqs), | |
| .num_regs = 1, | |
| .status_base = TWL6040_REG_INTID, | |
| .mask_base = TWL6040_REG_INTMR, | |
| }; | |
| static int twl6040_probe(struct i2c_client *client, | |
| const struct i2c_device_id *id) | |
| { | |
| struct device_node *node = client->dev.of_node; | |
| struct twl6040 *twl6040; | |
| struct mfd_cell *cell = NULL; | |
| int irq, ret, children = 0; | |
| if (!node) { | |
| dev_err(&client->dev, "of node is missing\n"); | |
| return -EINVAL; | |
| } | |
| /* In order to operate correctly we need valid interrupt config */ | |
| if (!client->irq) { | |
| dev_err(&client->dev, "Invalid IRQ configuration\n"); | |
| return -EINVAL; | |
| } | |
| twl6040 = devm_kzalloc(&client->dev, sizeof(struct twl6040), | |
| GFP_KERNEL); | |
| if (!twl6040) | |
| return -ENOMEM; | |
| twl6040->regmap = devm_regmap_init_i2c(client, &twl6040_regmap_config); | |
| if (IS_ERR(twl6040->regmap)) | |
| return PTR_ERR(twl6040->regmap); | |
| i2c_set_clientdata(client, twl6040); | |
| twl6040->clk32k = devm_clk_get(&client->dev, "clk32k"); | |
| if (IS_ERR(twl6040->clk32k)) { | |
| if (PTR_ERR(twl6040->clk32k) == -EPROBE_DEFER) | |
| return -EPROBE_DEFER; | |
| dev_dbg(&client->dev, "clk32k is not handled\n"); | |
| twl6040->clk32k = NULL; | |
| } | |
| twl6040->mclk = devm_clk_get(&client->dev, "mclk"); | |
| if (IS_ERR(twl6040->mclk)) { | |
| if (PTR_ERR(twl6040->mclk) == -EPROBE_DEFER) | |
| return -EPROBE_DEFER; | |
| dev_dbg(&client->dev, "mclk is not handled\n"); | |
| twl6040->mclk = NULL; | |
| } | |
| twl6040->supplies[0].supply = "vio"; | |
| twl6040->supplies[1].supply = "v2v1"; | |
| ret = devm_regulator_bulk_get(&client->dev, TWL6040_NUM_SUPPLIES, | |
| twl6040->supplies); | |
| if (ret != 0) { | |
| dev_err(&client->dev, "Failed to get supplies: %d\n", ret); | |
| return ret; | |
| } | |
| ret = regulator_bulk_enable(TWL6040_NUM_SUPPLIES, twl6040->supplies); | |
| if (ret != 0) { | |
| dev_err(&client->dev, "Failed to enable supplies: %d\n", ret); | |
| return ret; | |
| } | |
| twl6040->dev = &client->dev; | |
| twl6040->irq = client->irq; | |
| mutex_init(&twl6040->mutex); | |
| init_completion(&twl6040->ready); | |
| regmap_register_patch(twl6040->regmap, twl6040_patch, | |
| ARRAY_SIZE(twl6040_patch)); | |
| twl6040->rev = twl6040_reg_read(twl6040, TWL6040_REG_ASICREV); | |
| if (twl6040->rev < 0) { | |
| dev_err(&client->dev, "Failed to read revision register: %d\n", | |
| twl6040->rev); | |
| ret = twl6040->rev; | |
| goto gpio_err; | |
| } | |
| /* ERRATA: Automatic power-up is not possible in ES1.0 */ | |
| if (twl6040_get_revid(twl6040) > TWL6040_REV_ES1_0) | |
| twl6040->audpwron = of_get_named_gpio(node, | |
| "ti,audpwron-gpio", 0); | |
| else | |
| twl6040->audpwron = -EINVAL; | |
| if (gpio_is_valid(twl6040->audpwron)) { | |
| ret = devm_gpio_request_one(&client->dev, twl6040->audpwron, | |
| GPIOF_OUT_INIT_LOW, "audpwron"); | |
| if (ret) | |
| goto gpio_err; | |
| /* Clear any pending interrupt */ | |
| twl6040_reg_read(twl6040, TWL6040_REG_INTID); | |
| } | |
| ret = regmap_add_irq_chip(twl6040->regmap, twl6040->irq, IRQF_ONESHOT, | |
| 0, &twl6040_irq_chip, &twl6040->irq_data); | |
| if (ret < 0) | |
| goto gpio_err; | |
| twl6040->irq_ready = regmap_irq_get_virq(twl6040->irq_data, | |
| TWL6040_IRQ_READY); | |
| twl6040->irq_th = regmap_irq_get_virq(twl6040->irq_data, | |
| TWL6040_IRQ_TH); | |
| ret = devm_request_threaded_irq(twl6040->dev, twl6040->irq_ready, NULL, | |
| twl6040_readyint_handler, IRQF_ONESHOT, | |
| "twl6040_irq_ready", twl6040); | |
| if (ret) { | |
| dev_err(twl6040->dev, "READY IRQ request failed: %d\n", ret); | |
| goto readyirq_err; | |
| } | |
| ret = devm_request_threaded_irq(twl6040->dev, twl6040->irq_th, NULL, | |
| twl6040_thint_handler, IRQF_ONESHOT, | |
| "twl6040_irq_th", twl6040); | |
| if (ret) { | |
| dev_err(twl6040->dev, "Thermal IRQ request failed: %d\n", ret); | |
| goto readyirq_err; | |
| } | |
| /* | |
| * The main functionality of twl6040 to provide audio on OMAP4+ systems. | |
| * We can add the ASoC codec child whenever this driver has been loaded. | |
| */ | |
| irq = regmap_irq_get_virq(twl6040->irq_data, TWL6040_IRQ_PLUG); | |
| cell = &twl6040->cells[children]; | |
| cell->name = "twl6040-codec"; | |
| twl6040_codec_rsrc[0].start = irq; | |
| twl6040_codec_rsrc[0].end = irq; | |
| cell->resources = twl6040_codec_rsrc; | |
| cell->num_resources = ARRAY_SIZE(twl6040_codec_rsrc); | |
| children++; | |
| /* Vibra input driver support */ | |
| if (twl6040_has_vibra(node)) { | |
| irq = regmap_irq_get_virq(twl6040->irq_data, TWL6040_IRQ_VIB); | |
| cell = &twl6040->cells[children]; | |
| cell->name = "twl6040-vibra"; | |
| twl6040_vibra_rsrc[0].start = irq; | |
| twl6040_vibra_rsrc[0].end = irq; | |
| cell->resources = twl6040_vibra_rsrc; | |
| cell->num_resources = ARRAY_SIZE(twl6040_vibra_rsrc); | |
| children++; | |
| } | |
| /* GPO support */ | |
| cell = &twl6040->cells[children]; | |
| cell->name = "twl6040-gpo"; | |
| children++; | |
| /* PDM clock support */ | |
| cell = &twl6040->cells[children]; | |
| cell->name = "twl6040-pdmclk"; | |
| children++; | |
| /* The chip is powered down so mark regmap to cache only and dirty */ | |
| regcache_cache_only(twl6040->regmap, true); | |
| regcache_mark_dirty(twl6040->regmap); | |
| ret = mfd_add_devices(&client->dev, -1, twl6040->cells, children, | |
| NULL, 0, NULL); | |
| if (ret) | |
| goto readyirq_err; | |
| return 0; | |
| readyirq_err: | |
| regmap_del_irq_chip(twl6040->irq, twl6040->irq_data); | |
| gpio_err: | |
| regulator_bulk_disable(TWL6040_NUM_SUPPLIES, twl6040->supplies); | |
| return ret; | |
| } | |
| static int twl6040_remove(struct i2c_client *client) | |
| { | |
| struct twl6040 *twl6040 = i2c_get_clientdata(client); | |
| if (twl6040->power_count) | |
| twl6040_power(twl6040, 0); | |
| regmap_del_irq_chip(twl6040->irq, twl6040->irq_data); | |
| mfd_remove_devices(&client->dev); | |
| regulator_bulk_disable(TWL6040_NUM_SUPPLIES, twl6040->supplies); | |
| return 0; | |
| } | |
| static const struct i2c_device_id twl6040_i2c_id[] = { | |
| { "twl6040", 0, }, | |
| { "twl6041", 0, }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, twl6040_i2c_id); | |
| static struct i2c_driver twl6040_driver = { | |
| .driver = { | |
| .name = "twl6040", | |
| }, | |
| .probe = twl6040_probe, | |
| .remove = twl6040_remove, | |
| .id_table = twl6040_i2c_id, | |
| }; | |
| module_i2c_driver(twl6040_driver); | |
| MODULE_DESCRIPTION("TWL6040 MFD"); | |
| MODULE_AUTHOR("Misael Lopez Cruz <misael.lopez@ti.com>"); | |
| MODULE_AUTHOR("Jorge Eduardo Candelaria <jorge.candelaria@ti.com>"); | |
| MODULE_LICENSE("GPL"); |