# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/remoteproc/qcom,qcs404-cdsp-pil.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Qualcomm QCS404 CDSP Peripheral Image Loader

maintainers:
  - Bjorn Andersson <bjorn.andersson@linaro.org>

description:
  This document defines the binding for a component that loads and boots firmware
  on the Qualcomm Technology Inc. CDSP (Compute DSP).

properties:
  compatible:
    enum:
      - qcom,qcs404-cdsp-pil

  reg:
    maxItems: 1
    description:
      The base address and size of the qdsp6ss register

  interrupts:
    items:
      - description: Watchdog interrupt
      - description: Fatal interrupt
      - description: Ready interrupt
      - description: Handover interrupt
      - description: Stop acknowledge interrupt

  interrupt-names:
    items:
      - const: wdog
      - const: fatal
      - const: ready
      - const: handover
      - const: stop-ack

  clocks:
    items:
      - description: XO clock
      - description: SWAY clock
      - description: TBU clock
      - description: BIMC clock
      - description: AHB AON clock
      - description: Q6SS SLAVE clock
      - description: Q6SS MASTER clock
      - description: Q6 AXIM clock

  clock-names:
    items:
      - const: xo
      - const: sway
      - const: tbu
      - const: bimc
      - const: ahb_aon
      - const: q6ss_slave
      - const: q6ss_master
      - const: q6_axim

  power-domains:
    items:
      - description: CX power domain

  resets:
    items:
      - description: AOSS restart

  reset-names:
    items:
      - const: restart

  memory-region:
    maxItems: 1
    description: Reference to the reserved-memory for the Hexagon core

  qcom,halt-regs:
    $ref: /schemas/types.yaml#/definitions/phandle-array
    description:
      Phandle reference to a syscon representing TCSR followed by the
      three offsets within syscon for q6, modem and nc halt registers.

  qcom,smem-states:
    $ref: /schemas/types.yaml#/definitions/phandle-array
    description: States used by the AP to signal the Hexagon core
    items:
      - description: Stop the modem

  qcom,smem-state-names:
    description: The names of the state bits used for SMP2P output
    items:
      - const: stop

required:
  - compatible
  - reg
  - interrupts
  - interrupt-names
  - clocks
  - clock-names
  - power-domains
  - resets
  - reset-names
  - qcom,halt-regs
  - memory-region
  - qcom,smem-states
  - qcom,smem-state-names

additionalProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/arm-gic.h>
    #include <dt-bindings/clock/qcom,gcc-qcs404.h>
    #include <dt-bindings/power/qcom-rpmpd.h>
    #include <dt-bindings/clock/qcom,turingcc-qcs404.h>
    remoteproc@b00000 {
        compatible = "qcom,qcs404-cdsp-pil";
        reg = <0x00b00000 0x4040>;

        interrupts-extended = <&intc GIC_SPI 229 IRQ_TYPE_EDGE_RISING>,
                              <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
                              <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
                              <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
                              <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
        interrupt-names = "wdog", "fatal", "ready",
                          "handover", "stop-ack";

        clocks = <&xo_board>,
                 <&gcc GCC_CDSP_CFG_AHB_CLK>,
                 <&gcc GCC_CDSP_TBU_CLK>,
                 <&gcc GCC_BIMC_CDSP_CLK>,
                 <&turingcc TURING_WRAPPER_AON_CLK>,
                 <&turingcc TURING_Q6SS_AHBS_AON_CLK>,
                 <&turingcc TURING_Q6SS_AHBM_AON_CLK>,
                 <&turingcc TURING_Q6SS_Q6_AXIM_CLK>;
        clock-names = "xo",
                      "sway",
                      "tbu",
                      "bimc",
                      "ahb_aon",
                      "q6ss_slave",
                      "q6ss_master",
                      "q6_axim";

        power-domains = <&rpmhpd SDM845_CX>;

        resets = <&gcc GCC_CDSP_RESTART>;
        reset-names = "restart";

        qcom,halt-regs = <&tcsr 0x19004>;

        memory-region = <&cdsp_fw_mem>;

        qcom,smem-states = <&cdsp_smp2p_out 0>;
        qcom,smem-state-names = "stop";
    };