# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/can/nxp,sja1000.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Memory mapped SJA1000 CAN controller from NXP (formerly Philips)

maintainers:
  - Wolfgang Grandegger <wg@grandegger.com>

properties:
  compatible:
    oneOf:
      - enum:
          - nxp,sja1000
          - technologic,sja1000
      - items:
          - enum:
              - renesas,r9a06g032-sja1000 # RZ/N1D
              - renesas,r9a06g033-sja1000 # RZ/N1S
          - const: renesas,rzn1-sja1000 # RZ/N1

  reg:
    maxItems: 1

  interrupts:
    maxItems: 1

  clocks:
    maxItems: 1

  reg-io-width:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: I/O register width (in bytes) implemented by this device
    default: 1
    enum: [ 1, 2, 4 ]

  nxp,external-clock-frequency:
    $ref: /schemas/types.yaml#/definitions/uint32
    default: 16000000
    description: |
      Frequency of the external oscillator clock in Hz.
      The internal clock frequency used by the SJA1000 is half of that value.

  nxp,tx-output-mode:
    $ref: /schemas/types.yaml#/definitions/uint32
    enum: [ 0, 1, 2, 3 ]
    default: 1
    description: |
      operation mode of the TX output control logic. Valid values are:
        <0> : bi-phase output mode
        <1> : normal output mode (default)
        <2> : test output mode
        <3> : clock output mode

  nxp,tx-output-config:
    $ref: /schemas/types.yaml#/definitions/uint32
    default: 0x02
    description: |
      TX output pin configuration. Valid values are any one of the below
      or combination of TX0 and TX1:
        <0x01> : TX0 invert
        <0x02> : TX0 pull-down (default)
        <0x04> : TX0 pull-up
        <0x06> : TX0 push-pull
        <0x08> : TX1 invert
        <0x10> : TX1 pull-down
        <0x20> : TX1 pull-up
        <0x30> : TX1 push-pull

  nxp,clock-out-frequency:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: |
      clock frequency in Hz on the CLKOUT pin.
      If not specified or if the specified value is 0, the CLKOUT pin
      will be disabled.

  nxp,no-comparator-bypass:
    type: boolean
    description: Allows to disable the CAN input comparator.

required:
  - compatible
  - reg
  - interrupts

allOf:
  - $ref: can-controller.yaml#
  - if:
      properties:
        compatible:
          contains:
            enum:
              - technologic,sja1000
              - renesas,rzn1-sja1000
    then:
      required:
        - reg-io-width
  - if:
      properties:
        compatible:
          contains:
            const: renesas,rzn1-sja1000
    then:
      required:
        - clocks

unevaluatedProperties: false

examples:
  - |
    can@1a000 {
        compatible = "technologic,sja1000";
        reg = <0x1a000 0x100>;
        interrupts = <1>;
        reg-io-width = <2>;
        nxp,tx-output-config = <0x06>;
        nxp,external-clock-frequency = <24000000>;
    };

  - |
    #include <dt-bindings/interrupt-controller/arm-gic.h>
    #include <dt-bindings/clock/r9a06g032-sysctrl.h>

    can@52104000 {
        compatible = "renesas,r9a06g032-sja1000", "renesas,rzn1-sja1000";
        reg = <0x52104000 0x800>;
        reg-io-width = <4>;
        interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
        clocks = <&sysctrl R9A06G032_HCLK_CAN0>;
    };