// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2020, Linaro Limited
 */

#include <dt-bindings/interconnect/qcom,sm8350.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,dispcc-sm8350.h>
#include <dt-bindings/clock/qcom,gcc-sm8350.h>
#include <dt-bindings/clock/qcom,gpucc-sm8350.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/firmware/qcom,scm.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interconnect/qcom,sm8350.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/phy/phy-qcom-qmp.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/power/qcom,rpmhpd.h>
#include <dt-bindings/soc/qcom,apr.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include <dt-bindings/sound/qcom,q6afe.h>
#include <dt-bindings/thermal/thermal.h>
#include <dt-bindings/interconnect/qcom,sm8350.h>

/ {
	interrupt-parent = <&intc>;

	#address-cells = <2>;
	#size-cells = <2>;

	chosen { };

	clocks {
		xo_board: xo-board {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <38400000>;
			clock-output-names = "xo_board";
		};

		sleep_clk: sleep-clk {
			compatible = "fixed-clock";
			clock-frequency = <32000>;
			#clock-cells = <0>;
		};
	};

	cpus {
		#address-cells = <2>;
		#size-cells = <0>;

		CPU0: cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-a55";
			reg = <0x0 0x0>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			next-level-cache = <&L2_0>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			power-domains = <&CPU_PD0>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			L2_0: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
				L3_0: l3-cache {
					compatible = "cache";
					cache-level = <3>;
					cache-unified;
				};
			};
		};

		CPU1: cpu@100 {
			device_type = "cpu";
			compatible = "arm,cortex-a55";
			reg = <0x0 0x100>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			next-level-cache = <&L2_100>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			power-domains = <&CPU_PD1>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			L2_100: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU2: cpu@200 {
			device_type = "cpu";
			compatible = "arm,cortex-a55";
			reg = <0x0 0x200>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			next-level-cache = <&L2_200>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			power-domains = <&CPU_PD2>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			L2_200: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU3: cpu@300 {
			device_type = "cpu";
			compatible = "arm,cortex-a55";
			reg = <0x0 0x300>;
			clocks = <&cpufreq_hw 0>;
			enable-method = "psci";
			next-level-cache = <&L2_300>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			power-domains = <&CPU_PD3>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			L2_300: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU4: cpu@400 {
			device_type = "cpu";
			compatible = "arm,cortex-a78";
			reg = <0x0 0x400>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			next-level-cache = <&L2_400>;
			qcom,freq-domain = <&cpufreq_hw 1>;
			power-domains = <&CPU_PD4>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			L2_400: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU5: cpu@500 {
			device_type = "cpu";
			compatible = "arm,cortex-a78";
			reg = <0x0 0x500>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			next-level-cache = <&L2_500>;
			qcom,freq-domain = <&cpufreq_hw 1>;
			power-domains = <&CPU_PD5>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			L2_500: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU6: cpu@600 {
			device_type = "cpu";
			compatible = "arm,cortex-a78";
			reg = <0x0 0x600>;
			clocks = <&cpufreq_hw 1>;
			enable-method = "psci";
			next-level-cache = <&L2_600>;
			qcom,freq-domain = <&cpufreq_hw 1>;
			power-domains = <&CPU_PD6>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			L2_600: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU7: cpu@700 {
			device_type = "cpu";
			compatible = "arm,cortex-x1";
			reg = <0x0 0x700>;
			clocks = <&cpufreq_hw 2>;
			enable-method = "psci";
			next-level-cache = <&L2_700>;
			qcom,freq-domain = <&cpufreq_hw 2>;
			power-domains = <&CPU_PD7>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			L2_700: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		cpu-map {
			cluster0 {
				core0 {
					cpu = <&CPU0>;
				};

				core1 {
					cpu = <&CPU1>;
				};

				core2 {
					cpu = <&CPU2>;
				};

				core3 {
					cpu = <&CPU3>;
				};

				core4 {
					cpu = <&CPU4>;
				};

				core5 {
					cpu = <&CPU5>;
				};

				core6 {
					cpu = <&CPU6>;
				};

				core7 {
					cpu = <&CPU7>;
				};
			};
		};

		idle-states {
			entry-method = "psci";

			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
				compatible = "arm,idle-state";
				idle-state-name = "silver-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <360>;
				exit-latency-us = <531>;
				min-residency-us = <3934>;
				local-timer-stop;
			};

			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
				compatible = "arm,idle-state";
				idle-state-name = "gold-rail-power-collapse";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <702>;
				exit-latency-us = <1061>;
				min-residency-us = <4488>;
				local-timer-stop;
			};
		};

		domain-idle-states {
			CLUSTER_SLEEP_APSS_OFF: cluster-sleep-0 {
				compatible = "domain-idle-state";
				arm,psci-suspend-param = <0x41000044>;
				entry-latency-us = <2752>;
				exit-latency-us = <3048>;
				min-residency-us = <6118>;
			};

			CLUSTER_SLEEP_AOSS_SLEEP: cluster-sleep-1 {
				compatible = "domain-idle-state";
				arm,psci-suspend-param = <0x4100c344>;
				entry-latency-us = <3263>;
				exit-latency-us = <6562>;
				min-residency-us = <9987>;
			};
		};
	};

	firmware {
		scm: scm {
			compatible = "qcom,scm-sm8350", "qcom,scm";
			#reset-cells = <1>;
		};
	};

	memory@80000000 {
		device_type = "memory";
		/* We expect the bootloader to fill in the size */
		reg = <0x0 0x80000000 0x0 0x0>;
	};

	pmu {
		compatible = "arm,armv8-pmuv3";
		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>;
	};

	psci {
		compatible = "arm,psci-1.0";
		method = "smc";

		CPU_PD0: power-domain-cpu0 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD1: power-domain-cpu1 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD2: power-domain-cpu2 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD3: power-domain-cpu3 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD4: power-domain-cpu4 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD5: power-domain-cpu5 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD6: power-domain-cpu6 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD7: power-domain-cpu7 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CLUSTER_PD: power-domain-cpu-cluster0 {
			#power-domain-cells = <0>;
			domain-idle-states = <&CLUSTER_SLEEP_APSS_OFF &CLUSTER_SLEEP_AOSS_SLEEP>;
		};
	};

	qup_opp_table_100mhz: opp-table-qup100mhz {
		compatible = "operating-points-v2";

		opp-50000000 {
			opp-hz = /bits/ 64 <50000000>;
			required-opps = <&rpmhpd_opp_min_svs>;
		};

		opp-75000000 {
			opp-hz = /bits/ 64 <75000000>;
			required-opps = <&rpmhpd_opp_low_svs>;
		};

		opp-100000000 {
			opp-hz = /bits/ 64 <100000000>;
			required-opps = <&rpmhpd_opp_svs>;
		};
	};

	qup_opp_table_120mhz: opp-table-qup120mhz {
		compatible = "operating-points-v2";

		opp-50000000 {
			opp-hz = /bits/ 64 <50000000>;
			required-opps = <&rpmhpd_opp_min_svs>;
		};

		opp-75000000 {
			opp-hz = /bits/ 64 <75000000>;
			required-opps = <&rpmhpd_opp_low_svs>;
		};

		opp-120000000 {
			opp-hz = /bits/ 64 <120000000>;
			required-opps = <&rpmhpd_opp_svs>;
		};
	};

	reserved_memory: reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		hyp_mem: memory@80000000 {
			reg = <0x0 0x80000000 0x0 0x600000>;
			no-map;
		};

		xbl_aop_mem: memory@80700000 {
			no-map;
			reg = <0x0 0x80700000 0x0 0x160000>;
		};

		cmd_db: memory@80860000 {
			compatible = "qcom,cmd-db";
			reg = <0x0 0x80860000 0x0 0x20000>;
			no-map;
		};

		reserved_xbl_uefi_log: memory@80880000 {
			reg = <0x0 0x80880000 0x0 0x14000>;
			no-map;
		};

		smem@80900000 {
			compatible = "qcom,smem";
			reg = <0x0 0x80900000 0x0 0x200000>;
			hwlocks = <&tcsr_mutex 3>;
			no-map;
		};

		cpucp_fw_mem: memory@80b00000 {
			reg = <0x0 0x80b00000 0x0 0x100000>;
			no-map;
		};

		cdsp_secure_heap: memory@80c00000 {
			reg = <0x0 0x80c00000 0x0 0x4600000>;
			no-map;
		};

		pil_camera_mem: mmeory@85200000 {
			reg = <0x0 0x85200000 0x0 0x500000>;
			no-map;
		};

		pil_video_mem: memory@85700000 {
			reg = <0x0 0x85700000 0x0 0x500000>;
			no-map;
		};

		pil_cvp_mem: memory@85c00000 {
			reg = <0x0 0x85c00000 0x0 0x500000>;
			no-map;
		};

		pil_adsp_mem: memory@86100000 {
			reg = <0x0 0x86100000 0x0 0x2100000>;
			no-map;
		};

		pil_slpi_mem: memory@88200000 {
			reg = <0x0 0x88200000 0x0 0x1500000>;
			no-map;
		};

		pil_cdsp_mem: memory@89700000 {
			reg = <0x0 0x89700000 0x0 0x1e00000>;
			no-map;
		};

		pil_ipa_fw_mem: memory@8b500000 {
			reg = <0x0 0x8b500000 0x0 0x10000>;
			no-map;
		};

		pil_ipa_gsi_mem: memory@8b510000 {
			reg = <0x0 0x8b510000 0x0 0xa000>;
			no-map;
		};

		pil_gpu_mem: memory@8b51a000 {
			reg = <0x0 0x8b51a000 0x0 0x2000>;
			no-map;
		};

		pil_spss_mem: memory@8b600000 {
			reg = <0x0 0x8b600000 0x0 0x100000>;
			no-map;
		};

		pil_modem_mem: memory@8b800000 {
			reg = <0x0 0x8b800000 0x0 0x10000000>;
			no-map;
		};

		rmtfs_mem: memory@9b800000 {
			compatible = "qcom,rmtfs-mem";
			reg = <0x0 0x9b800000 0x0 0x280000>;
			no-map;

			qcom,client-id = <1>;
			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
		};

		hyp_reserved_mem: memory@d0000000 {
			reg = <0x0 0xd0000000 0x0 0x800000>;
			no-map;
		};

		pil_trustedvm_mem: memory@d0800000 {
			reg = <0x0 0xd0800000 0x0 0x76f7000>;
			no-map;
		};

		qrtr_shbuf: memory@d7ef7000 {
			reg = <0x0 0xd7ef7000 0x0 0x9000>;
			no-map;
		};

		chan0_shbuf: memory@d7f00000 {
			reg = <0x0 0xd7f00000 0x0 0x80000>;
			no-map;
		};

		chan1_shbuf: memory@d7f80000 {
			reg = <0x0 0xd7f80000 0x0 0x80000>;
			no-map;
		};

		removed_mem: memory@d8800000 {
			reg = <0x0 0xd8800000 0x0 0x6800000>;
			no-map;
		};
	};

	smp2p-adsp {
		compatible = "qcom,smp2p";
		qcom,smem = <443>, <429>;
		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_LPASS
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <2>;

		smp2p_adsp_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_adsp_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-cdsp {
		compatible = "qcom,smp2p";
		qcom,smem = <94>, <432>;
		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_CDSP
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <5>;

		smp2p_cdsp_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_cdsp_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-modem {
		compatible = "qcom,smp2p";
		qcom,smem = <435>, <428>;
		interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_MPSS
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <1>;

		smp2p_modem_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_modem_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};

		ipa_smp2p_out: ipa-ap-to-modem {
			qcom,entry-name = "ipa";
			#qcom,smem-state-cells = <1>;
		};

		ipa_smp2p_in: ipa-modem-to-ap {
			qcom,entry-name = "ipa";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-slpi {
		compatible = "qcom,smp2p";
		qcom,smem = <481>, <430>;
		interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
					     IPCC_MPROC_SIGNAL_SMP2P
					     IRQ_TYPE_EDGE_RISING>;
		mboxes = <&ipcc IPCC_CLIENT_SLPI
				IPCC_MPROC_SIGNAL_SMP2P>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <3>;

		smp2p_slpi_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		smp2p_slpi_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	soc: soc@0 {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges = <0 0 0 0 0x10 0>;
		dma-ranges = <0 0 0 0 0x10 0>;
		compatible = "simple-bus";

		gcc: clock-controller@100000 {
			compatible = "qcom,gcc-sm8350";
			reg = <0x0 0x00100000 0x0 0x1f0000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			clock-names = "bi_tcxo",
				      "sleep_clk",
				      "pcie_0_pipe_clk",
				      "pcie_1_pipe_clk",
				      "ufs_card_rx_symbol_0_clk",
				      "ufs_card_rx_symbol_1_clk",
				      "ufs_card_tx_symbol_0_clk",
				      "ufs_phy_rx_symbol_0_clk",
				      "ufs_phy_rx_symbol_1_clk",
				      "ufs_phy_tx_symbol_0_clk",
				      "usb3_phy_wrapper_gcc_usb30_pipe_clk",
				      "usb3_uni_phy_sec_gcc_usb30_pipe_clk";
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&sleep_clk>,
				 <&pcie0_phy>,
				 <&pcie1_phy>,
				 <0>,
				 <0>,
				 <0>,
				 <&ufs_mem_phy_lanes 0>,
				 <&ufs_mem_phy_lanes 1>,
				 <&ufs_mem_phy_lanes 2>,
				 <&usb_1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
				 <0>;
		};

		ipcc: mailbox@408000 {
			compatible = "qcom,sm8350-ipcc", "qcom,ipcc";
			reg = <0 0x00408000 0 0x1000>;
			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-controller;
			#interrupt-cells = <3>;
			#mbox-cells = <2>;
		};

		gpi_dma2: dma-controller@800000 {
			compatible = "qcom,sm8350-gpi-dma", "qcom,sm6350-gpi-dma";
			reg = <0 0x00800000 0 0x60000>;
			interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 599 IRQ_TYPE_LEVEL_HIGH>;
			dma-channels = <12>;
			dma-channel-mask = <0xff>;
			iommus = <&apps_smmu 0x5f6 0x0>;
			#dma-cells = <3>;
			status = "disabled";
		};

		qupv3_id_2: geniqup@8c0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0x0 0x008c0000 0x0 0x6000>;
			clock-names = "m-ahb", "s-ahb";
			clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
			iommus = <&apps_smmu 0x5e3 0x0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			status = "disabled";

			i2c14: i2c@880000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00880000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c14_default>;
				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 0 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi14: spi@880000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00880000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_120mhz>;
				dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 0 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c15: i2c@884000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00884000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c15_default>;
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 1 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi15: spi@884000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00884000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_120mhz>;
				dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 1 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c16: i2c@888000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00888000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c16_default>;
				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 2 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi16: spi@888000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00888000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 2 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c17: i2c@88c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0088c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c17_default>;
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 3 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi17: spi@88c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0088c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma2 0 3 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 3 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			/* QUP no. 18 seems to be strictly SPI/UART-only */

			spi18: spi@890000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00890000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma2 0 4 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 4 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart18: serial@890000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00890000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart18_default>;
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				status = "disabled";
			};

			i2c19: i2c@894000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00894000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c19_default>;
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
				       <&gpi_dma2 1 5 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi19: spi@894000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00894000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
				       <&gpi_dma2 1 5 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};
		};

		gpi_dma0: dma-controller@9800000 {
			compatible = "qcom,sm8350-gpi-dma", "qcom,sm6350-gpi-dma";
			reg = <0 0x09800000 0 0x60000>;
			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
			dma-channels = <12>;
			dma-channel-mask = <0x7e>;
			iommus = <&apps_smmu 0x5b6 0x0>;
			#dma-cells = <3>;
			status = "disabled";
		};

		qupv3_id_0: geniqup@9c0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0x0 0x009c0000 0x0 0x6000>;
			clock-names = "m-ahb", "s-ahb";
			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
			iommus = <&apps_smmu 0x5a3 0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			status = "disabled";

			i2c0: i2c@980000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00980000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c0_default>;
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi0: spi@980000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00980000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c1: i2c@984000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00984000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c1_default>;
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi1: spi@984000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00984000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c2: i2c@988000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00988000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c2_default>;
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi2: spi@988000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00988000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart2: serial@98c000 {
				compatible = "qcom,geni-debug-uart";
				reg = <0 0x0098c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart3_default_state>;
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				status = "disabled";
			};

			/* QUP no. 3 seems to be strictly SPI-only */

			spi3: spi@98c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0098c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 3 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c4: i2c@990000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00990000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c4_default>;
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi4: spi@990000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00990000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 4 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c5: i2c@994000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00994000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c5_default>;
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi5: spi@994000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00994000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 5 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c6: i2c@998000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00998000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c6_default>;
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 6 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi6: spi@998000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00998000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 6 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart6: serial@998000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00998000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_uart6_default>;
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				status = "disabled";
			};

			i2c7: i2c@99c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0099c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c7_default>;
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>,
				       <&gpi_dma0 1 7 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi7: spi@99c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0099c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>,
				       <&gpi_dma0 1 7 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};
		};

		gpi_dma1: dma-controller@a00000 {
			compatible = "qcom,sm8350-gpi-dma", "qcom,sm6350-gpi-dma";
			reg = <0 0x00a00000 0 0x60000>;
			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
			dma-channels = <12>;
			dma-channel-mask = <0xff>;
			iommus = <&apps_smmu 0x56 0x0>;
			#dma-cells = <3>;
			status = "disabled";
		};

		qupv3_id_1: geniqup@ac0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0x0 0x00ac0000 0x0 0x6000>;
			clock-names = "m-ahb", "s-ahb";
			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
			iommus = <&apps_smmu 0x43 0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			status = "disabled";

			i2c8: i2c@a80000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a80000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c8_default>;
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi8: spi@a80000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a80000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_120mhz>;
				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c9: i2c@a84000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a84000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c9_default>;
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi9: spi@a84000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a84000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c10: i2c@a88000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a88000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c10_default>;
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi10: spi@a88000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a88000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c11: i2c@a8c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a8c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c11_default>;
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi11: spi@a8c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a8c000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c12: i2c@a90000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a90000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c12_default>;
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi12: spi@a90000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a90000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			i2c13: i2c@a94000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a94000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				pinctrl-names = "default";
				pinctrl-0 = <&qup_i2c13_default>;
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi13: spi@a94000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a94000 0 0x4000>;
				clock-names = "se";
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				power-domains = <&rpmhpd RPMHPD_CX>;
				operating-points-v2 = <&qup_opp_table_100mhz>;
				dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
				       <&gpi_dma1 1 5 QCOM_GPI_SPI>;
				dma-names = "tx", "rx";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};
		};

		rng: rng@10d3000 {
			compatible = "qcom,prng-ee";
			reg = <0 0x010d3000 0 0x1000>;
			clocks = <&rpmhcc RPMH_HWKM_CLK>;
			clock-names = "core";
		};

		config_noc: interconnect@1500000 {
			compatible = "qcom,sm8350-config-noc";
			reg = <0 0x01500000 0 0xa580>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		mc_virt: interconnect@1580000 {
			compatible = "qcom,sm8350-mc-virt";
			reg = <0 0x01580000 0 0x1000>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		system_noc: interconnect@1680000 {
			compatible = "qcom,sm8350-system-noc";
			reg = <0 0x01680000 0 0x1c200>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		aggre1_noc: interconnect@16e0000 {
			compatible = "qcom,sm8350-aggre1-noc";
			reg = <0 0x016e0000 0 0x1f180>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		aggre2_noc: interconnect@1700000 {
			compatible = "qcom,sm8350-aggre2-noc";
			reg = <0 0x01700000 0 0x33000>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		mmss_noc: interconnect@1740000 {
			compatible = "qcom,sm8350-mmss-noc";
			reg = <0 0x01740000 0 0x1f080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		pcie0: pci@1c00000 {
			compatible = "qcom,pcie-sm8350";
			reg = <0 0x01c00000 0 0x3000>,
			      <0 0x60000000 0 0xf1d>,
			      <0 0x60000f20 0 0xa8>,
			      <0 0x60001000 0 0x1000>,
			      <0 0x60100000 0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			device_type = "pci";
			linux,pci-domain = <0>;
			bus-range = <0x00 0xff>;
			num-lanes = <1>;

			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>,
				 <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>;

			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi0", "msi1", "msi2", "msi3",
					  "msi4", "msi5", "msi6", "msi7";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "tbu",
				      "ddrss_sf_tbu",
				      "aggre1",
				      "aggre0";

			iommu-map = <0x0   &apps_smmu 0x1c00 0x1>,
				    <0x100 &apps_smmu 0x1c01 0x1>;

			resets = <&gcc GCC_PCIE_0_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_0_GDSC>;

			phys = <&pcie0_phy>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie0_phy: phy@1c06000 {
			compatible = "qcom,sm8350-qmp-gen3x1-pcie-phy";
			reg = <0 0x01c06000 0 0x2000>;
			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_0_CLKREF_EN>,
				 <&gcc GCC_PCIE0_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_0_PIPE_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng", "pipe";

			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE0_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			#clock-cells = <0>;
			clock-output-names = "pcie_0_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		pcie1: pci@1c08000 {
			compatible = "qcom,pcie-sm8350";
			reg = <0 0x01c08000 0 0x3000>,
			      <0 0x40000000 0 0xf1d>,
			      <0 0x40000f20 0 0xa8>,
			      <0 0x40001000 0 0x1000>,
			      <0 0x40100000 0 0x100000>;
			reg-names = "parf", "dbi", "elbi", "atu", "config";
			device_type = "pci";
			linux,pci-domain = <1>;
			bus-range = <0x00 0xff>;
			num-lanes = <2>;

			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;

			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
			clock-names = "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "tbu",
				      "ddrss_sf_tbu",
				      "aggre1";

			iommu-map = <0x0   &apps_smmu 0x1c80 0x1>,
				    <0x100 &apps_smmu 0x1c81 0x1>;

			resets = <&gcc GCC_PCIE_1_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_1_GDSC>;

			phys = <&pcie1_phy>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie1_phy: phy@1c0e000 {
			compatible = "qcom,sm8350-qmp-gen3x2-pcie-phy";
			reg = <0 0x01c0e000 0 0x2000>;
			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_1_CLKREF_EN>,
				 <&gcc GCC_PCIE1_PHY_RCHNG_CLK>,
				 <&gcc GCC_PCIE_1_PIPE_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "rchng", "pipe";

			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
			assigned-clock-rates = <100000000>;

			#clock-cells = <0>;
			clock-output-names = "pcie_1_pipe_clk";

			#phy-cells = <0>;

			status = "disabled";
		};

		ufs_mem_hc: ufshc@1d84000 {
			compatible = "qcom,sm8350-ufshc", "qcom,ufshc",
				     "jedec,ufs-2.0";
			reg = <0 0x01d84000 0 0x3000>;
			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
			phys = <&ufs_mem_phy_lanes>;
			phy-names = "ufsphy";
			lanes-per-direction = <2>;
			#reset-cells = <1>;
			resets = <&gcc GCC_UFS_PHY_BCR>;
			reset-names = "rst";

			power-domains = <&gcc UFS_PHY_GDSC>;

			iommus = <&apps_smmu 0xe0 0x0>;
			dma-coherent;

			clock-names =
				"core_clk",
				"bus_aggr_clk",
				"iface_clk",
				"core_clk_unipro",
				"ref_clk",
				"tx_lane0_sync_clk",
				"rx_lane0_sync_clk",
				"rx_lane1_sync_clk";
			clocks =
				<&gcc GCC_UFS_PHY_AXI_CLK>,
				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
				<&gcc GCC_UFS_PHY_AHB_CLK>,
				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
				<&rpmhcc RPMH_CXO_CLK>,
				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
			freq-table-hz =
				<75000000 300000000>,
				<0 0>,
				<0 0>,
				<75000000 300000000>,
				<0 0>,
				<0 0>,
				<0 0>,
				<0 0>;
			status = "disabled";
		};

		ufs_mem_phy: phy@1d87000 {
			compatible = "qcom,sm8350-qmp-ufs-phy";
			reg = <0 0x01d87000 0 0x1c4>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			clock-names = "ref",
				      "ref_aux";
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;

			resets = <&ufs_mem_hc 0>;
			reset-names = "ufsphy";
			status = "disabled";

			ufs_mem_phy_lanes: phy@1d87400 {
				reg = <0 0x01d87400 0 0x188>,
				      <0 0x01d87600 0 0x200>,
				      <0 0x01d87c00 0 0x200>,
				      <0 0x01d87800 0 0x188>,
				      <0 0x01d87a00 0 0x200>;
				#clock-cells = <1>;
				#phy-cells = <0>;
			};
		};

		cryptobam: dma-controller@1dc4000 {
			compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0";
			reg = <0 0x01dc4000 0 0x24000>;
			interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
			#dma-cells = <1>;
			qcom,ee = <0>;
			qcom,controlled-remotely;
			iommus = <&apps_smmu 0x594 0x0011>,
				 <&apps_smmu 0x596 0x0011>;
			/* FIXME: Probing BAM DMA causes some abort and system hang */
			status = "fail";
		};

		crypto: crypto@1dfa000 {
			compatible = "qcom,sm8350-qce", "qcom,sm8150-qce", "qcom,qce";
			reg = <0 0x01dfa000 0 0x6000>;
			dmas = <&cryptobam 4>, <&cryptobam 5>;
			dma-names = "rx", "tx";
			iommus = <&apps_smmu 0x594 0x0011>,
				 <&apps_smmu 0x596 0x0011>;
			interconnects = <&aggre2_noc MASTER_CRYPTO 0 &mc_virt SLAVE_EBI1 0>;
			interconnect-names = "memory";
			/* FIXME: dependency BAM DMA is disabled */
			status = "disabled";
		};

		ipa: ipa@1e40000 {
			compatible = "qcom,sm8350-ipa";

			iommus = <&apps_smmu 0x5c0 0x0>,
				 <&apps_smmu 0x5c2 0x0>;
			reg = <0 0x01e40000 0 0x8000>,
			      <0 0x01e50000 0 0x4b20>,
			      <0 0x01e04000 0 0x23000>;
			reg-names = "ipa-reg",
				    "ipa-shared",
				    "gsi";

			interrupts-extended = <&intc GIC_SPI 655 IRQ_TYPE_EDGE_RISING>,
					      <&intc GIC_SPI 432 IRQ_TYPE_LEVEL_HIGH>,
					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "ipa",
					  "gsi",
					  "ipa-clock-query",
					  "ipa-setup-ready";

			clocks = <&rpmhcc RPMH_IPA_CLK>;
			clock-names = "core";

			interconnects = <&aggre2_noc MASTER_IPA 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_IPA_CFG 0>;
			interconnect-names = "memory",
					     "config";

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&ipa_smp2p_out 0>,
					   <&ipa_smp2p_out 1>;
			qcom,smem-state-names = "ipa-clock-enabled-valid",
						"ipa-clock-enabled";

			status = "disabled";
		};

		tcsr_mutex: hwlock@1f40000 {
			compatible = "qcom,tcsr-mutex";
			reg = <0x0 0x01f40000 0x0 0x40000>;
			#hwlock-cells = <1>;
		};

		lpass_tlmm: pinctrl@33c0000 {
			compatible = "qcom,sm8350-lpass-lpi-pinctrl";
			reg = <0 0x033c0000 0 0x20000>,
			      <0 0x03550000 0 0x10000>;

			clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
				 <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
			clock-names = "core", "audio";

			gpio-controller;
			#gpio-cells = <2>;
			gpio-ranges = <&lpass_tlmm 0 0 15>;
		};

		gpu: gpu@3d00000 {
			compatible = "qcom,adreno-660.1", "qcom,adreno";

			reg = <0 0x03d00000 0 0x40000>,
			      <0 0x03d9e000 0 0x1000>,
			      <0 0x03d61000 0 0x800>;
			reg-names = "kgsl_3d0_reg_memory",
				    "cx_mem",
				    "cx_dbgc";

			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;

			iommus = <&adreno_smmu 0 0x400>, <&adreno_smmu 1 0x400>;

			operating-points-v2 = <&gpu_opp_table>;

			qcom,gmu = <&gmu>;

			status = "disabled";

			zap-shader {
				memory-region = <&pil_gpu_mem>;
			};

			/* note: downstream checks gpu binning for 670 Mhz */
			gpu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-840000000 {
					opp-hz = /bits/ 64 <840000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
				};

				opp-778000000 {
					opp-hz = /bits/ 64 <778000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
				};

				opp-738000000 {
					opp-hz = /bits/ 64 <738000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
				};

				opp-676000000 {
					opp-hz = /bits/ 64 <676000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
				};

				opp-608000000 {
					opp-hz = /bits/ 64 <608000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
				};

				opp-540000000 {
					opp-hz = /bits/ 64 <540000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
				};

				opp-491000000 {
					opp-hz = /bits/ 64 <491000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L0>;
				};

				opp-443000000 {
					opp-hz = /bits/ 64 <443000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
				};

				opp-379000000 {
					opp-hz = /bits/ 64 <379000000>;
					opp-level = <80 /* RPMH_REGULATOR_LEVEL_LOW_SVS_L1 */>;
				};

				opp-315000000 {
					opp-hz = /bits/ 64 <315000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
				};
			};
		};

		gmu: gmu@3d6a000 {
			compatible = "qcom,adreno-gmu-660.1", "qcom,adreno-gmu";

			reg = <0 0x03d6a000 0 0x34000>,
			      <0 0x03de0000 0 0x10000>,
			      <0 0x0b290000 0 0x10000>;
			reg-names = "gmu", "rscc", "gmu_pdc";

			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hfi", "gmu";

			clocks = <&gpucc GPU_CC_CX_GMU_CLK>,
				 <&gpucc GPU_CC_CXO_CLK>,
				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
				 <&gpucc GPU_CC_AHB_CLK>,
				 <&gpucc GPU_CC_HUB_CX_INT_CLK>,
				 <&gpucc GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK>;
			clock-names = "gmu",
				      "cxo",
				      "axi",
				      "memnoc",
				      "ahb",
				      "hub",
				      "smmu_vote";

			power-domains = <&gpucc GPU_CX_GDSC>,
					<&gpucc GPU_GX_GDSC>;
			power-domain-names = "cx",
					     "gx";

			iommus = <&adreno_smmu 5 0x400>;

			operating-points-v2 = <&gmu_opp_table>;

			gmu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-200000000 {
					opp-hz = /bits/ 64 <200000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
				};
			};
		};

		gpucc: clock-controller@3d90000 {
			compatible = "qcom,sm8350-gpucc";
			reg = <0 0x03d90000 0 0x9000>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
			clock-names = "bi_tcxo",
				      "gcc_gpu_gpll0_clk_src",
				      "gcc_gpu_gpll0_div_clk_src";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		adreno_smmu: iommu@3da0000 {
			compatible = "qcom,sm8350-smmu-500", "qcom,adreno-smmu",
				     "qcom,smmu-500", "arm,mmu-500";
			reg = <0 0x03da0000 0 0x20000>;
			#iommu-cells = <2>;
			#global-interrupts = <2>;
			interrupts = <GIC_SPI 672 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 673 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 678 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 679 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 680 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 686 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 687 IRQ_TYPE_LEVEL_HIGH>;

			clocks = <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
				 <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>,
				 <&gpucc GPU_CC_AHB_CLK>,
				 <&gpucc GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK>,
				 <&gpucc GPU_CC_CX_GMU_CLK>,
				 <&gpucc GPU_CC_HUB_CX_INT_CLK>,
				 <&gpucc GPU_CC_HUB_AON_CLK>;
			clock-names = "bus",
				      "iface",
				      "ahb",
				      "hlos1_vote_gpu_smmu",
				      "cx_gmu",
				      "hub_cx_int",
				      "hub_aon";

			power-domains = <&gpucc GPU_CX_GDSC>;
			dma-coherent;
		};

		lpass_ag_noc: interconnect@3c40000 {
			compatible = "qcom,sm8350-lpass-ag-noc";
			reg = <0 0x03c40000 0 0xf080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		mpss: remoteproc@4080000 {
			compatible = "qcom,sm8350-mpss-pas";
			reg = <0x0 0x04080000 0x0 0x4040>;

			interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>,
					      <&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_modem_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_modem_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_modem_in 3 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_modem_in 7 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready", "handover",
					  "stop-ack", "shutdown-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd RPMHPD_CX>,
					<&rpmhpd RPMHPD_MSS>;
			power-domain-names = "cx", "mss";

			interconnects = <&mc_virt MASTER_LLCC 0 &mc_virt SLAVE_EBI1 0>;

			memory-region = <&pil_modem_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_modem_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_MPSS
						IPCC_MPROC_SIGNAL_GLINK_QMP>;
				label = "modem";
				qcom,remote-pid = <1>;
			};
		};

		slpi: remoteproc@5c00000 {
			compatible = "qcom,sm8350-slpi-pas";
			reg = <0 0x05c00000 0 0x4000>;

			interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
					      <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd RPMHPD_LCX>,
					<&rpmhpd RPMHPD_LMX>;
			power-domain-names = "lcx", "lmx";

			memory-region = <&pil_slpi_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_slpi_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_SLPI
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "slpi";
				qcom,remote-pid = <3>;

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,glink-channels = "fastrpcglink-apps-dsp";
					label = "sdsp";
					qcom,non-secure-domain;
					#address-cells = <1>;
					#size-cells = <0>;

					compute-cb@1 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <1>;
						iommus = <&apps_smmu 0x0541 0x0>;
					};

					compute-cb@2 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <2>;
						iommus = <&apps_smmu 0x0542 0x0>;
					};

					compute-cb@3 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <3>;
						iommus = <&apps_smmu 0x0543 0x0>;
						/* note: shared-cb = <4> in downstream */
					};
				};
			};
		};

		sdhc_2: mmc@8804000 {
			compatible = "qcom,sm8350-sdhci", "qcom,sdhci-msm-v5";
			reg = <0 0x08804000 0 0x1000>;

			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hc_irq", "pwr_irq";

			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
				 <&gcc GCC_SDCC2_APPS_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "iface", "core", "xo";
			resets = <&gcc GCC_SDCC2_BCR>;
			interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>;
			interconnect-names = "sdhc-ddr","cpu-sdhc";
			iommus = <&apps_smmu 0x4a0 0x0>;
			power-domains = <&rpmhpd RPMHPD_CX>;
			operating-points-v2 = <&sdhc2_opp_table>;
			bus-width = <4>;
			dma-coherent;

			status = "disabled";

			sdhc2_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-100000000 {
					opp-hz = /bits/ 64 <100000000>;
					required-opps = <&rpmhpd_opp_low_svs>;
				};

				opp-202000000 {
					opp-hz = /bits/ 64 <202000000>;
					required-opps = <&rpmhpd_opp_svs_l1>;
				};
			};
		};

		usb_1_hsphy: phy@88e3000 {
			compatible = "qcom,sm8350-usb-hs-phy",
				     "qcom,usb-snps-hs-7nm-phy";
			reg = <0 0x088e3000 0 0x400>;
			status = "disabled";
			#phy-cells = <0>;

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "ref";

			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
		};

		usb_2_hsphy: phy@88e4000 {
			compatible = "qcom,sm8250-usb-hs-phy",
				     "qcom,usb-snps-hs-7nm-phy";
			reg = <0 0x088e4000 0 0x400>;
			status = "disabled";
			#phy-cells = <0>;

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "ref";

			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
		};

		usb_1_qmpphy: phy@88e8000 {
			compatible = "qcom,sm8350-qmp-usb3-dp-phy";
			reg = <0 0x088e8000 0 0x3000>;

			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
			clock-names = "aux", "ref", "com_aux", "usb3_pipe";

			resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
			reset-names = "phy", "common";

			#clock-cells = <1>;
			#phy-cells = <1>;

			status = "disabled";

			ports {
				#address-cells = <1>;
				#size-cells = <0>;

				port@0 {
					reg = <0>;

					usb_1_qmpphy_out: endpoint {
					};
				};

				port@1 {
					reg = <1>;

					usb_1_qmpphy_usb_ss_in: endpoint {
					};
				};

				port@2 {
					reg = <2>;

					usb_1_qmpphy_dp_in: endpoint {
					};
				};
			};
		};

		usb_2_qmpphy: phy-wrapper@88eb000 {
			compatible = "qcom,sm8350-qmp-usb3-uni-phy";
			reg = <0 0x088eb000 0 0x200>;
			status = "disabled";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_USB3_SEC_CLKREF_EN>,
				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
			clock-names = "aux", "ref_clk_src", "ref", "com_aux";

			resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
				 <&gcc GCC_USB3_PHY_SEC_BCR>;
			reset-names = "phy", "common";

			usb_2_ssphy: phy@88ebe00 {
				reg = <0 0x088ebe00 0 0x200>,
				      <0 0x088ec000 0 0x200>,
				      <0 0x088eb200 0 0x1100>;
				#phy-cells = <0>;
				#clock-cells = <0>;
				clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
				clock-names = "pipe0";
				clock-output-names = "usb3_uni_phy_pipe_clk_src";
			};
		};

		dc_noc: interconnect@90c0000 {
			compatible = "qcom,sm8350-dc-noc";
			reg = <0 0x090c0000 0 0x4200>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		gem_noc: interconnect@9100000 {
			compatible = "qcom,sm8350-gem-noc";
			reg = <0 0x09100000 0 0xb4000>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		system-cache-controller@9200000 {
			compatible = "qcom,sm8350-llcc";
			reg = <0 0x09200000 0 0x58000>, <0 0x09280000 0 0x58000>,
			      <0 0x09300000 0 0x58000>, <0 0x09380000 0 0x58000>,
			      <0 0x09600000 0 0x58000>;
			reg-names = "llcc0_base", "llcc1_base", "llcc2_base",
				    "llcc3_base", "llcc_broadcast_base";
		};

		compute_noc: interconnect@a0c0000 {
			compatible = "qcom,sm8350-compute-noc";
			reg = <0 0x0a0c0000 0 0xa180>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		usb_1: usb@a6f8800 {
			compatible = "qcom,sm8350-dwc3", "qcom,dwc3";
			reg = <0 0x0a6f8800 0 0x400>;
			status = "disabled";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
			clock-names = "cfg_noc",
				      "core",
				      "iface",
				      "sleep",
				      "mock_utmi";

			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>;
			interrupt-names = "hs_phy_irq",
					  "ss_phy_irq",
					  "dm_hs_phy_irq",
					  "dp_hs_phy_irq";

			power-domains = <&gcc USB30_PRIM_GDSC>;

			resets = <&gcc GCC_USB30_PRIM_BCR>;

			interconnects = <&aggre1_noc MASTER_USB3_0 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_0 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			usb_1_dwc3: usb@a600000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a600000 0 0xcd00>;
				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x0 0x0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_enblslpm_quirk;
				phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
				phy-names = "usb2-phy", "usb3-phy";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;

						usb_1_dwc3_hs: endpoint {
						};
					};

					port@1 {
						reg = <1>;

						usb_1_dwc3_ss: endpoint {
						};
					};
				};
			};
		};

		usb_2: usb@a8f8800 {
			compatible = "qcom,sm8350-dwc3", "qcom,dwc3";
			reg = <0 0x0a8f8800 0 0x400>;
			status = "disabled";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
				 <&gcc GCC_USB3_SEC_CLKREF_EN>;
			clock-names = "cfg_noc",
				      "core",
				      "iface",
				      "sleep",
				      "mock_utmi",
				      "xo";

			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 16 IRQ_TYPE_LEVEL_HIGH>,
					      <&pdc 13 IRQ_TYPE_EDGE_BOTH>,
					      <&pdc 12 IRQ_TYPE_EDGE_BOTH>;
			interrupt-names = "hs_phy_irq",
					  "ss_phy_irq",
					  "dm_hs_phy_irq",
					  "dp_hs_phy_irq";

			power-domains = <&gcc USB30_SEC_GDSC>;

			resets = <&gcc GCC_USB30_SEC_BCR>;

			interconnects = <&aggre1_noc MASTER_USB3_1 0 &mc_virt SLAVE_EBI1 0>,
					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_1 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			usb_2_dwc3: usb@a800000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a800000 0 0xcd00>;
				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x20 0x0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_enblslpm_quirk;
				phys = <&usb_2_hsphy>, <&usb_2_ssphy>;
				phy-names = "usb2-phy", "usb3-phy";
			};
		};

		mdss: display-subsystem@ae00000 {
			compatible = "qcom,sm8350-mdss";
			reg = <0 0x0ae00000 0 0x1000>;
			reg-names = "mdss";

			interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
					<&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
			interconnect-names = "mdp0-mem", "mdp1-mem";

			power-domains = <&dispcc MDSS_GDSC>;
			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;

			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
				 <&gcc GCC_DISP_HF_AXI_CLK>,
				 <&gcc GCC_DISP_SF_AXI_CLK>,
				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
			clock-names = "iface", "bus", "nrt_bus", "core";

			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-controller;
			#interrupt-cells = <1>;

			iommus = <&apps_smmu 0x820 0x402>;

			status = "disabled";

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			dpu_opp_table: opp-table {
				compatible = "operating-points-v2";

				/* TODO: opp-200000000 should work with
				 * &rpmhpd_opp_low_svs, but one some of
				 * sm8350_hdk boards reboot using this
				 * opp.
				 */
				opp-200000000 {
					opp-hz = /bits/ 64 <200000000>;
					required-opps = <&rpmhpd_opp_svs>;
				};

				opp-300000000 {
					opp-hz = /bits/ 64 <300000000>;
					required-opps = <&rpmhpd_opp_svs>;
				};

				opp-345000000 {
					opp-hz = /bits/ 64 <345000000>;
					required-opps = <&rpmhpd_opp_svs_l1>;
				};

				opp-460000000 {
					opp-hz = /bits/ 64 <460000000>;
					required-opps = <&rpmhpd_opp_nom>;
				};
			};

			mdss_mdp: display-controller@ae01000 {
				compatible = "qcom,sm8350-dpu";
				reg = <0 0x0ae01000 0 0x8f000>,
				      <0 0x0aeb0000 0 0x2008>;
				reg-names = "mdp", "vbif";

				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
					<&gcc GCC_DISP_SF_AXI_CLK>,
					<&dispcc DISP_CC_MDSS_AHB_CLK>,
					<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
					<&dispcc DISP_CC_MDSS_MDP_CLK>,
					<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
				clock-names = "bus",
					      "nrt_bus",
					      "iface",
					      "lut",
					      "core",
					      "vsync";

				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
				assigned-clock-rates = <19200000>;

				operating-points-v2 = <&dpu_opp_table>;
				power-domains = <&rpmhpd RPMHPD_MMCX>;

				interrupt-parent = <&mdss>;
				interrupts = <0>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						dpu_intf1_out: endpoint {
							remote-endpoint = <&mdss_dsi0_in>;
						};
					};

					port@1 {
						reg = <1>;
						dpu_intf2_out: endpoint {
							remote-endpoint = <&mdss_dsi1_in>;
						};
					};

					port@2 {
						reg = <2>;
						dpu_intf0_out: endpoint {
							remote-endpoint = <&mdss_dp_in>;
						};
					};
				};
			};

			mdss_dp: displayport-controller@ae90000 {
				compatible = "qcom,sm8350-dp";
				reg = <0 0xae90000 0 0x200>,
				      <0 0xae90200 0 0x200>,
				      <0 0xae90400 0 0x600>,
				      <0 0xae91000 0 0x400>,
				      <0 0xae91400 0 0x400>;
				interrupt-parent = <&mdss>;
				interrupts = <12>;
				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
				clock-names = "core_iface",
					      "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface",
					      "stream_pixel";

				assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
						  <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
				assigned-clock-parents = <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
							 <&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;

				phys = <&usb_1_qmpphy QMP_USB43DP_DP_PHY>;
				phy-names = "dp";

				#sound-dai-cells = <0>;

				operating-points-v2 = <&dp_opp_table>;
				power-domains = <&rpmhpd RPMHPD_MMCX>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dp_in: endpoint {
							remote-endpoint = <&dpu_intf0_out>;
						};
					};
				};

				dp_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss_dsi0: dsi@ae94000 {
				compatible = "qcom,sm8350-dsi-ctrl", "qcom,mdss-dsi-ctrl";
				reg = <0 0x0ae94000 0 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <4>;

				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&gcc GCC_DISP_HF_AXI_CLK>;
				clock-names = "byte",
					      "byte_intf",
					      "pixel",
					      "core",
					      "iface",
					      "bus";

				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
						  <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
				assigned-clock-parents = <&mdss_dsi0_phy 0>,
							 <&mdss_dsi0_phy 1>;

				operating-points-v2 = <&dsi0_opp_table>;
				power-domains = <&rpmhpd RPMHPD_MMCX>;

				phys = <&mdss_dsi0_phy>;

				#address-cells = <1>;
				#size-cells = <0>;

				status = "disabled";

				dsi0_opp_table: opp-table {
					compatible = "operating-points-v2";

					/* TODO: opp-187500000 should work with
					 * &rpmhpd_opp_low_svs, but one some of
					 * sm8350_hdk boards reboot using this
					 * opp.
					 */
					opp-187500000 {
						opp-hz = /bits/ 64 <187500000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-300000000 {
						opp-hz = /bits/ 64 <300000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-358000000 {
						opp-hz = /bits/ 64 <358000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};
				};

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dsi0_in: endpoint {
							remote-endpoint = <&dpu_intf1_out>;
						};
					};

					port@1 {
						reg = <1>;
						mdss_dsi0_out: endpoint {
						};
					};
				};
			};

			mdss_dsi0_phy: phy@ae94400 {
				compatible = "qcom,sm8350-dsi-phy-5nm";
				reg = <0 0x0ae94400 0 0x200>,
				      <0 0x0ae94600 0 0x280>,
				      <0 0x0ae94900 0 0x27c>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&rpmhcc RPMH_CXO_CLK>;
				clock-names = "iface", "ref";

				status = "disabled";
			};

			mdss_dsi1: dsi@ae96000 {
				compatible = "qcom,sm8350-dsi-ctrl", "qcom,mdss-dsi-ctrl";
				reg = <0 0x0ae96000 0 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <5>;

				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&gcc GCC_DISP_HF_AXI_CLK>;
				clock-names = "byte",
					      "byte_intf",
					      "pixel",
					      "core",
					      "iface",
					      "bus";

				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>,
						  <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
				assigned-clock-parents = <&mdss_dsi1_phy 0>,
							 <&mdss_dsi1_phy 1>;

				operating-points-v2 = <&dsi1_opp_table>;
				power-domains = <&rpmhpd RPMHPD_MMCX>;

				phys = <&mdss_dsi1_phy>;

				#address-cells = <1>;
				#size-cells = <0>;

				status = "disabled";

				dsi1_opp_table: opp-table {
					compatible = "operating-points-v2";

					/* TODO: opp-187500000 should work with
					 * &rpmhpd_opp_low_svs, but one some of
					 * sm8350_hdk boards reboot using this
					 * opp.
					 */
					opp-187500000 {
						opp-hz = /bits/ 64 <187500000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-300000000 {
						opp-hz = /bits/ 64 <300000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-358000000 {
						opp-hz = /bits/ 64 <358000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};
				};

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						mdss_dsi1_in: endpoint {
							remote-endpoint = <&dpu_intf2_out>;
						};
					};

					port@1 {
						reg = <1>;
						mdss_dsi1_out: endpoint {
						};
					};
				};
			};

			mdss_dsi1_phy: phy@ae96400 {
				compatible = "qcom,sm8350-dsi-phy-5nm";
				reg = <0 0x0ae96400 0 0x200>,
				      <0 0x0ae96600 0 0x280>,
				      <0 0x0ae96900 0 0x27c>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&rpmhcc RPMH_CXO_CLK>;
				clock-names = "iface", "ref";

				status = "disabled";
			};
		};

		dispcc: clock-controller@af00000 {
			compatible = "qcom,sm8350-dispcc";
			reg = <0 0x0af00000 0 0x10000>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>,
				 <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>,
				 <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
				 <&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
			clock-names = "bi_tcxo",
				      "dsi0_phy_pll_out_byteclk",
				      "dsi0_phy_pll_out_dsiclk",
				      "dsi1_phy_pll_out_byteclk",
				      "dsi1_phy_pll_out_dsiclk",
				      "dp_phy_pll_link_clk",
				      "dp_phy_pll_vco_div_clk";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;

			power-domains = <&rpmhpd RPMHPD_MMCX>;
		};

		pdc: interrupt-controller@b220000 {
			compatible = "qcom,sm8350-pdc", "qcom,pdc";
			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
			qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>,   <55 306 4>,
					  <59 312 3>, <62 374 2>,  <64 434 2>,   <66 438 3>,
					  <69 86 1>,  <70 520 54>, <124 609 31>, <155 63 1>,
					  <156 716 12>;
			#interrupt-cells = <2>;
			interrupt-parent = <&intc>;
			interrupt-controller;
		};

		tsens0: thermal-sensor@c263000 {
			compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
			reg = <0 0x0c263000 0 0x1ff>, /* TM */
			      <0 0x0c222000 0 0x8>; /* SROT */
			#qcom,sensors = <15>;
			interrupts-extended = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
				     <&pdc 28 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		tsens1: thermal-sensor@c265000 {
			compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
			reg = <0 0x0c265000 0 0x1ff>, /* TM */
			      <0 0x0c223000 0 0x8>; /* SROT */
			#qcom,sensors = <14>;
			interrupts-extended = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
				     <&pdc 29 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		aoss_qmp: power-management@c300000 {
			compatible = "qcom,sm8350-aoss-qmp", "qcom,aoss-qmp";
			reg = <0 0x0c300000 0 0x400>;
			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
						     IRQ_TYPE_EDGE_RISING>;
			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;

			#clock-cells = <0>;
		};

		sram@c3f0000 {
			compatible = "qcom,rpmh-stats";
			reg = <0 0x0c3f0000 0 0x400>;
		};

		spmi_bus: spmi@c440000 {
			compatible = "qcom,spmi-pmic-arb";
			reg = <0x0 0x0c440000 0x0 0x1100>,
			      <0x0 0x0c600000 0x0 0x2000000>,
			      <0x0 0x0e600000 0x0 0x100000>,
			      <0x0 0x0e700000 0x0 0xa0000>,
			      <0x0 0x0c40a000 0x0 0x26000>;
			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
			interrupt-names = "periph_irq";
			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
			qcom,ee = <0>;
			qcom,channel = <0>;
			#address-cells = <2>;
			#size-cells = <0>;
			interrupt-controller;
			#interrupt-cells = <4>;
		};

		tlmm: pinctrl@f100000 {
			compatible = "qcom,sm8350-tlmm";
			reg = <0 0x0f100000 0 0x300000>;
			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			gpio-ranges = <&tlmm 0 0 204>;
			wakeup-parent = <&pdc>;

			sdc2_default_state: sdc2-default-state {
				clk-pins {
					pins = "sdc2_clk";
					drive-strength = <16>;
					bias-disable;
				};

				cmd-pins {
					pins = "sdc2_cmd";
					drive-strength = <16>;
					bias-pull-up;
				};

				data-pins {
					pins = "sdc2_data";
					drive-strength = <16>;
					bias-pull-up;
				};
			};

			sdc2_sleep_state: sdc2-sleep-state {
				clk-pins {
					pins = "sdc2_clk";
					drive-strength = <2>;
					bias-disable;
				};

				cmd-pins {
					pins = "sdc2_cmd";
					drive-strength = <2>;
					bias-pull-up;
				};

				data-pins {
					pins = "sdc2_data";
					drive-strength = <2>;
					bias-pull-up;
				};
			};

			qup_uart3_default_state: qup-uart3-default-state {
				rx-pins {
					pins = "gpio18";
					function = "qup3";
				};
				tx-pins {
					pins = "gpio19";
					function = "qup3";
				};
			};

			qup_uart6_default: qup-uart6-default-state {
				pins = "gpio30", "gpio31";
				function = "qup6";
				drive-strength = <2>;
				bias-disable;
			};

			qup_uart18_default: qup-uart18-default-state {
				pins = "gpio68", "gpio69";
				function = "qup18";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c0_default: qup-i2c0-default-state {
				pins = "gpio4", "gpio5";
				function = "qup0";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c1_default: qup-i2c1-default-state {
				pins = "gpio8", "gpio9";
				function = "qup1";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c2_default: qup-i2c2-default-state {
				pins = "gpio12", "gpio13";
				function = "qup2";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c4_default: qup-i2c4-default-state {
				pins = "gpio20", "gpio21";
				function = "qup4";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c5_default: qup-i2c5-default-state {
				pins = "gpio24", "gpio25";
				function = "qup5";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c6_default: qup-i2c6-default-state {
				pins = "gpio28", "gpio29";
				function = "qup6";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c7_default: qup-i2c7-default-state {
				pins = "gpio32", "gpio33";
				function = "qup7";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c8_default: qup-i2c8-default-state {
				pins = "gpio36", "gpio37";
				function = "qup8";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c9_default: qup-i2c9-default-state {
				pins = "gpio40", "gpio41";
				function = "qup9";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c10_default: qup-i2c10-default-state {
				pins = "gpio44", "gpio45";
				function = "qup10";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c11_default: qup-i2c11-default-state {
				pins = "gpio48", "gpio49";
				function = "qup11";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c12_default: qup-i2c12-default-state {
				pins = "gpio52", "gpio53";
				function = "qup12";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c13_default: qup-i2c13-default-state {
				pins = "gpio0", "gpio1";
				function = "qup13";
				drive-strength = <2>;
				bias-pull-up;
			};

			qup_i2c14_default: qup-i2c14-default-state {
				pins = "gpio56", "gpio57";
				function = "qup14";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c15_default: qup-i2c15-default-state {
				pins = "gpio60", "gpio61";
				function = "qup15";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c16_default: qup-i2c16-default-state {
				pins = "gpio64", "gpio65";
				function = "qup16";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c17_default: qup-i2c17-default-state {
				pins = "gpio72", "gpio73";
				function = "qup17";
				drive-strength = <2>;
				bias-disable;
			};

			qup_i2c19_default: qup-i2c19-default-state {
				pins = "gpio76", "gpio77";
				function = "qup19";
				drive-strength = <2>;
				bias-disable;
			};
		};

		apps_smmu: iommu@15000000 {
			compatible = "qcom,sm8350-smmu-500", "arm,mmu-500";
			reg = <0 0x15000000 0 0x100000>;
			#iommu-cells = <2>;
			#global-interrupts = <2>;
			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>;
		};

		adsp: remoteproc@17300000 {
			compatible = "qcom,sm8350-adsp-pas";
			reg = <0 0x17300000 0 0x100>;

			interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd RPMHPD_LCX>,
					<&rpmhpd RPMHPD_LMX>;
			power-domain-names = "lcx", "lmx";

			memory-region = <&pil_adsp_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_adsp_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_LPASS
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "lpass";
				qcom,remote-pid = <2>;

				apr {
					compatible = "qcom,apr-v2";
					qcom,glink-channels = "apr_audio_svc";
					qcom,domain = <APR_DOMAIN_ADSP>;
					#address-cells = <1>;
					#size-cells = <0>;

					service@3 {
						reg = <APR_SVC_ADSP_CORE>;
						compatible = "qcom,q6core";
						qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";
					};

					q6afe: service@4 {
						compatible = "qcom,q6afe";
						reg = <APR_SVC_AFE>;
						qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";

						q6afedai: dais {
							compatible = "qcom,q6afe-dais";
							#address-cells = <1>;
							#size-cells = <0>;
							#sound-dai-cells = <1>;
						};

						q6afecc: clock-controller {
							compatible = "qcom,q6afe-clocks";
							#clock-cells = <2>;
						};
					};

					q6asm: service@7 {
						compatible = "qcom,q6asm";
						reg = <APR_SVC_ASM>;
						qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";

						q6asmdai: dais {
							compatible = "qcom,q6asm-dais";
							#address-cells = <1>;
							#size-cells = <0>;
							#sound-dai-cells = <1>;
							iommus = <&apps_smmu 0x1801 0x0>;

							dai@0 {
								reg = <0>;
							};

							dai@1 {
								reg = <1>;
							};

							dai@2 {
								reg = <2>;
							};
						};
					};

					q6adm: service@8 {
						compatible = "qcom,q6adm";
						reg = <APR_SVC_ADM>;
						qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd";

						q6routing: routing {
							compatible = "qcom,q6adm-routing";
							#sound-dai-cells = <0>;
						};
					};
				};

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,glink-channels = "fastrpcglink-apps-dsp";
					label = "adsp";
					qcom,non-secure-domain;
					#address-cells = <1>;
					#size-cells = <0>;

					compute-cb@3 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <3>;
						iommus = <&apps_smmu 0x1803 0x0>;
					};

					compute-cb@4 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <4>;
						iommus = <&apps_smmu 0x1804 0x0>;
					};

					compute-cb@5 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <5>;
						iommus = <&apps_smmu 0x1805 0x0>;
					};
				};
			};
		};

		intc: interrupt-controller@17a00000 {
			compatible = "arm,gic-v3";
			#interrupt-cells = <3>;
			interrupt-controller;
			#redistributor-regions = <1>;
			redistributor-stride = <0 0x20000>;
			reg = <0x0 0x17a00000 0x0 0x10000>,     /* GICD */
			      <0x0 0x17a60000 0x0 0x100000>;    /* GICR * 8 */
			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
		};

		timer@17c20000 {
			compatible = "arm,armv7-timer-mem";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0 0 0 0x20000000>;
			reg = <0x0 0x17c20000 0x0 0x1000>;
			clock-frequency = <19200000>;

			frame@17c21000 {
				frame-number = <0>;
				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c21000 0x1000>,
				      <0x17c22000 0x1000>;
			};

			frame@17c23000 {
				frame-number = <1>;
				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c23000 0x1000>;
				status = "disabled";
			};

			frame@17c25000 {
				frame-number = <2>;
				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c25000 0x1000>;
				status = "disabled";
			};

			frame@17c27000 {
				frame-number = <3>;
				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c27000 0x1000>;
				status = "disabled";
			};

			frame@17c29000 {
				frame-number = <4>;
				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c29000 0x1000>;
				status = "disabled";
			};

			frame@17c2b000 {
				frame-number = <5>;
				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c2b000 0x1000>;
				status = "disabled";
			};

			frame@17c2d000 {
				frame-number = <6>;
				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x17c2d000 0x1000>;
				status = "disabled";
			};
		};

		apps_rsc: rsc@18200000 {
			label = "apps_rsc";
			compatible = "qcom,rpmh-rsc";
			reg = <0x0 0x18200000 0x0 0x10000>,
				<0x0 0x18210000 0x0 0x10000>,
				<0x0 0x18220000 0x0 0x10000>;
			reg-names = "drv-0", "drv-1", "drv-2";
			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
			qcom,tcs-offset = <0xd00>;
			qcom,drv-id = <2>;
			qcom,tcs-config = <ACTIVE_TCS  2>, <SLEEP_TCS   3>,
					  <WAKE_TCS    3>, <CONTROL_TCS 0>;
			power-domains = <&CLUSTER_PD>;

			rpmhcc: clock-controller {
				compatible = "qcom,sm8350-rpmh-clk";
				#clock-cells = <1>;
				clock-names = "xo";
				clocks = <&xo_board>;
			};

			rpmhpd: power-controller {
				compatible = "qcom,sm8350-rpmhpd";
				#power-domain-cells = <1>;
				operating-points-v2 = <&rpmhpd_opp_table>;

				rpmhpd_opp_table: opp-table {
					compatible = "operating-points-v2";

					rpmhpd_opp_ret: opp1 {
						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
					};

					rpmhpd_opp_min_svs: opp2 {
						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
					};

					rpmhpd_opp_low_svs: opp3 {
						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
					};

					rpmhpd_opp_svs: opp4 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
					};

					rpmhpd_opp_svs_l1: opp5 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
					};

					rpmhpd_opp_nom: opp6 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
					};

					rpmhpd_opp_nom_l1: opp7 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
					};

					rpmhpd_opp_nom_l2: opp8 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
					};

					rpmhpd_opp_turbo: opp9 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
					};

					rpmhpd_opp_turbo_l1: opp10 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
					};
				};
			};

			apps_bcm_voter: bcm-voter {
				compatible = "qcom,bcm-voter";
			};
		};

		cpufreq_hw: cpufreq@18591000 {
			compatible = "qcom,sm8350-cpufreq-epss", "qcom,cpufreq-epss";
			reg = <0 0x18591000 0 0x1000>,
			      <0 0x18592000 0 0x1000>,
			      <0 0x18593000 0 0x1000>;
			reg-names = "freq-domain0", "freq-domain1", "freq-domain2";

			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "dcvsh-irq-0",
					  "dcvsh-irq-1",
					  "dcvsh-irq-2";

			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
			clock-names = "xo", "alternate";

			#freq-domain-cells = <1>;
			#clock-cells = <1>;
		};

		cdsp: remoteproc@98900000 {
			compatible = "qcom,sm8350-cdsp-pas";
			reg = <0 0x98900000 0 0x1400000>;

			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
					      <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd RPMHPD_CX>,
					<&rpmhpd RPMHPD_MXC>;
			power-domain-names = "cx", "mxc";

			interconnects = <&compute_noc MASTER_CDSP_PROC 0 &mc_virt SLAVE_EBI1 0>;

			memory-region = <&pil_cdsp_mem>;

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&smp2p_cdsp_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			glink-edge {
				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
							     IPCC_MPROC_SIGNAL_GLINK_QMP
							     IRQ_TYPE_EDGE_RISING>;
				mboxes = <&ipcc IPCC_CLIENT_CDSP
						IPCC_MPROC_SIGNAL_GLINK_QMP>;

				label = "cdsp";
				qcom,remote-pid = <5>;

				fastrpc {
					compatible = "qcom,fastrpc";
					qcom,glink-channels = "fastrpcglink-apps-dsp";
					label = "cdsp";
					qcom,non-secure-domain;
					#address-cells = <1>;
					#size-cells = <0>;

					compute-cb@1 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <1>;
						iommus = <&apps_smmu 0x2161 0x0400>,
							 <&apps_smmu 0x1181 0x0420>;
					};

					compute-cb@2 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <2>;
						iommus = <&apps_smmu 0x2162 0x0400>,
							 <&apps_smmu 0x1182 0x0420>;
					};

					compute-cb@3 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <3>;
						iommus = <&apps_smmu 0x2163 0x0400>,
							 <&apps_smmu 0x1183 0x0420>;
					};

					compute-cb@4 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <4>;
						iommus = <&apps_smmu 0x2164 0x0400>,
							 <&apps_smmu 0x1184 0x0420>;
					};

					compute-cb@5 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <5>;
						iommus = <&apps_smmu 0x2165 0x0400>,
							 <&apps_smmu 0x1185 0x0420>;
					};

					compute-cb@6 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <6>;
						iommus = <&apps_smmu 0x2166 0x0400>,
							 <&apps_smmu 0x1186 0x0420>;
					};

					compute-cb@7 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <7>;
						iommus = <&apps_smmu 0x2167 0x0400>,
							 <&apps_smmu 0x1187 0x0420>;
					};

					compute-cb@8 {
						compatible = "qcom,fastrpc-compute-cb";
						reg = <8>;
						iommus = <&apps_smmu 0x2168 0x0400>,
							 <&apps_smmu 0x1188 0x0420>;
					};

					/* note: secure cb9 in downstream */
				};
			};
		};
	};

	thermal_zones: thermal-zones {
		cpu0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 1>;

			trips {
				cpu0_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu0_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu0_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu0_alert0>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu0_alert1>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 2>;

			trips {
				cpu1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu1_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu1_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu1_alert0>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu1_alert1>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu2-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 3>;

			trips {
				cpu2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu2_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu2_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu2_alert0>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu2_alert1>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu3-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 4>;

			trips {
				cpu3_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu3_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu3_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu3_alert0>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu3_alert1>;
					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu4-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 7>;

			trips {
				cpu4_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_top_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu4_top_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu4_top_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu5-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 8>;

			trips {
				cpu5_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_top_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu5_top_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu5_top_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu6-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 9>;

			trips {
				cpu6_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_top_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu6_top_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu6_top_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu7-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 10>;

			trips {
				cpu7_top_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_top_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_top_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu7_top_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu7_top_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu4-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 11>;

			trips {
				cpu4_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu4_bottom_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu4_bottom_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu4_bottom_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu5-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 12>;

			trips {
				cpu5_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu5_bottom_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu5_bottom_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu5_bottom_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu6-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 13>;

			trips {
				cpu6_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu6_bottom_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu6_bottom_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu6_bottom_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		cpu7-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 14>;

			trips {
				cpu7_bottom_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_bottom_alert1: trip-point1 {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "passive";
				};

				cpu7_bottom_crit: cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu7_bottom_alert0>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
				map1 {
					trip = <&cpu7_bottom_alert1>;
					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		aoss0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 0>;

			trips {
				aoss0_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		cluster0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 5>;

			trips {
				cluster0_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
				cluster0_crit: cluster0_crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cluster1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 6>;

			trips {
				cluster1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
				cluster1_crit: cluster1_crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		aoss1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 0>;

			trips {
				aoss1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		gpu-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 1>;

			trips {
				gpu1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <1000>;
					type = "hot";
				};
			};
		};

		gpu-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 2>;

			trips {
				gpu2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <1000>;
					type = "hot";
				};
			};
		};

		nspss1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 3>;

			trips {
				nspss1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <1000>;
					type = "hot";
				};
			};
		};

		nspss2-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 4>;

			trips {
				nspss2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <1000>;
					type = "hot";
				};
			};
		};

		nspss3-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 5>;

			trips {
				nspss3_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <1000>;
					type = "hot";
				};
			};
		};

		video-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 6>;

			trips {
				video_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		mem-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 7>;

			trips {
				mem_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		modem1-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 8>;

			trips {
				modem1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		modem2-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 9>;

			trips {
				modem2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		modem3-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 10>;

			trips {
				modem3_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		modem4-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 11>;

			trips {
				modem4_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		camera-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 12>;

			trips {
				camera1_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		cam-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 13>;

			trips {
				camera2_alert0: trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
	};
};