| /* |
| * arch/ppc/platforms/ebony.h |
| * |
| * Ebony board definitions |
| * |
| * Matt Porter <mporter@mvista.com> |
| * |
| * Copyright 2002 MontaVista Software Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| */ |
| |
| #ifdef __KERNEL__ |
| #ifndef __ASM_EBONY_H__ |
| #define __ASM_EBONY_H__ |
| |
| #include <linux/config.h> |
| #include <platforms/4xx/ibm440gp.h> |
| |
| /* F/W TLB mapping used in bootloader glue to reset EMAC */ |
| #define PPC44x_EMAC0_MR0 0xE0000800 |
| |
| /* Where to find the MAC info */ |
| #define EBONY_OPENBIOS_MAC_BASE 0xfffffe0c |
| #define EBONY_OPENBIOS_MAC_OFFSET 0x0c |
| |
| /* Default clock rates for Rev. B and Rev. C silicon */ |
| #define EBONY_440GP_RB_SYSCLK 33000000 |
| #define EBONY_440GP_RC_SYSCLK 400000000 |
| |
| /* RTC/NVRAM location */ |
| #define EBONY_RTC_ADDR 0x0000000148000000ULL |
| #define EBONY_RTC_SIZE 0x2000 |
| |
| /* Flash */ |
| #define EBONY_FPGA_ADDR 0x0000000148300000ULL |
| #define EBONY_BOOT_SMALL_FLASH(x) (x & 0x20) |
| #define EBONY_ONBRD_FLASH_EN(x) (x & 0x02) |
| #define EBONY_FLASH_SEL(x) (x & 0x01) |
| #define EBONY_SMALL_FLASH_LOW1 0x00000001ff800000ULL |
| #define EBONY_SMALL_FLASH_LOW2 0x00000001ff880000ULL |
| #define EBONY_SMALL_FLASH_HIGH1 0x00000001fff00000ULL |
| #define EBONY_SMALL_FLASH_HIGH2 0x00000001fff80000ULL |
| #define EBONY_SMALL_FLASH_SIZE 0x80000 |
| #define EBONY_LARGE_FLASH_LOW 0x00000001ff800000ULL |
| #define EBONY_LARGE_FLASH_HIGH 0x00000001ffc00000ULL |
| #define EBONY_LARGE_FLASH_SIZE 0x400000 |
| |
| #define EBONY_SMALL_FLASH_BASE 0x00000001fff80000ULL |
| #define EBONY_LARGE_FLASH_BASE 0x00000001ff800000ULL |
| |
| /* |
| * Serial port defines |
| */ |
| |
| /* OpenBIOS defined UART mappings, used before early_serial_setup */ |
| #define UART0_IO_BASE 0xE0000200 |
| #define UART1_IO_BASE 0xE0000300 |
| |
| /* external Epson SG-615P */ |
| #define BASE_BAUD 691200 |
| |
| #define STD_UART_OP(num) \ |
| { 0, BASE_BAUD, 0, UART##num##_INT, \ |
| (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST), \ |
| iomem_base: UART##num##_IO_BASE, \ |
| io_type: SERIAL_IO_MEM}, |
| |
| #define SERIAL_PORT_DFNS \ |
| STD_UART_OP(0) \ |
| STD_UART_OP(1) |
| |
| /* PCI support */ |
| #define EBONY_PCI_LOWER_IO 0x00000000 |
| #define EBONY_PCI_UPPER_IO 0x0000ffff |
| #define EBONY_PCI_LOWER_MEM 0x80002000 |
| #define EBONY_PCI_UPPER_MEM 0xffffefff |
| |
| #define EBONY_PCI_CFGREGS_BASE 0x000000020ec00000 |
| #define EBONY_PCI_CFGA_PLB32 0x0ec00000 |
| #define EBONY_PCI_CFGD_PLB32 0x0ec00004 |
| |
| #define EBONY_PCI_IO_BASE 0x0000000208000000ULL |
| #define EBONY_PCI_IO_SIZE 0x00010000 |
| #define EBONY_PCI_MEM_OFFSET 0x00000000 |
| |
| #endif /* __ASM_EBONY_H__ */ |
| #endif /* __KERNEL__ */ |
